1、 EIA STANDARD Fixed Capacitors for Use in Electronic Equipment Part 16: Sectional Specification Fixed Metallized Polypropylene Film Dielectric d.c. Capacitors EIA-60384-16 (IEC 60384-16:2005, IDT) October 2014 ANSI/EIA-60384-16-2014 Approved: October 10, 2014 EIA-60384-16 NOTICE EIA Engineering Stan
2、dards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facili-tating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for
3、his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conform-ing to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their vol
4、untary use by those other than ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not as-sume any liabilit
5、y to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is identical (IDT) with the International Standard IEC Publication 60384-16:2005: Fixed Capacitors for Use in Electronic Equipment Part 16: Section-al Specification Fi
6、xed Metallized Polypropylene Film Dielectric d.c. Capacitors. This document is the EIA Standard EIA-60384-16 2014 Edition 2: Fixed Capacitors for Use in Electronic Equipment Part 16: Sectional Specification Fixed Metallized Polypropylene Film Dielectric d.c. Capacitors. The text, figures and tables
7、of IEC 60384-16:2005 are used in this Standard with the consent of the IEC and the American National Standards Institute (ANSI). These ma-terials are subject to copyright claims of IEC and ECIA. No part of this publication may be reproduced in any form, including an electronic retrieval system, with
8、out the prior written permission of ECIA. All requests pertaining to EIA-60384-16 2014 Edi-tion 2: Fixed Capacitors for Use in Electronic Equipment Part 16: Sectional Specifi-cation Fixed Metallized Polypropylene Film Dielectric d.c. Capacitors should be submitted to ECIA at the address below. The I
9、EC copyrighted material has been re-produced with permission from ANSI. The IEC Foreword and Introduction are not part of the requirements of this standard but are included for information purposes only. This Standard does not purport to address all safety problems associated with its use or all app
10、licable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5277, formulated under the cognizance of the P-2.2 Com
11、mittee on EIA Paper, Film, Mica any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the Inter
12、-national Organization for Standardization (ISO) in accordance with conditions determined by agreement be-tween the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an internation-al consensus of opinion on the relevant subjects sin
13、ce each technical committee has representation from all in-terested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical conten
14、t of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misin-terpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possibl
15、e in their national and regional publications. Any divergence be-tween any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equip-m
16、ent declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC
17、 National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and ex-penses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publica-tions. 8) Atte
18、ntion is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. I
19、EC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60384-16 has been prepared by IEC technical committee 40: Ca-pacitors and resistors for electronic equipment. This second edition cancels and replaces the first edition published in 1982, amend
20、ment 1 (1987) and amendment 2 (1992) and constitutes minor revisions related to tables, figures and references. The text of this standard is based on the following documents: FDIS Report on voting 40/1595/FDIS 40/1628/RVD Full information on the voting for the approval of this standard can be found
21、in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. EIA-60384-16 Page 2 IEC 60384 consists of the following parts, under the (new) general title Fixed capacitors for use in electronic equipment: Part 1: Generic sp
22、ecification Part 2: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric d.c. capacitors Part 3: Sectional specification: Fixed tantalum chip capacitors Part 4: Sectional specification: Aluminium electrolytic capacitors with solid and non-solid electrolyte Part 5: Sec
23、tional specification: Fixed mica dielectric d.c. capacitors with a rated voltage not exceeding 3000 V Selection of methods of test and general requirements Part 6: Sectional specification: Fixed metallized polycarbonate film dielectric d.c. capaci-tors Part 7: Sectional specification: Fixed polystyr
24、ene film dielectric metal foil d.c. capacitors Part 8: Sectional specification: Fixed capacitors of ceramic dielectric, Class 1 Part 9: Sectional specification: Fixed capacitors of ceramic dielectric, Class 2 Part 11: Sectional specification: Fixed polyethylene-terephthalate film dielectric metal fo
25、il d.c. capacitors Part 12: Sectional specification: Fixed polycarbonate film dielectric metal foil d.c. capaci-tors Part 13: Sectional specification: Fixed polypropylene film dielectric metal foil d.c. capaci-tors Part 14: Sectional specification: Fixed capacitors for electromagnetic interference s
26、up-pression and connection to the supply mains Part 15: Sectional specification: Fixed tantalum capacitors with non-solid or solid electro-lyte Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c. capaci-tors Part 17: Sectional specification: Fixed metallized polypro
27、pylene film dielectric a.c. and pulse capacitors Part 18: Sectional specification: Fixed aluminium electrolytic chip capacitors with solid and non-solid electrolyte Part 19: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric chip d.c. capacitors Part 20: Sectional s
28、pecification: Fixed metallized polyphenylene sulfide film dielectric chip d.c. capacitors Part 21: Sectional specification: Fixed surface mount multilayer capacitors of ceramic die-lectric, Class 1 Part 22: Sectional specification: Fixed surface mount multilayer capacitors of ceramic die-lectric, Cl
29、ass 2 Part 23: Sectional specification: Fixed surface mount metallized polyethylene naphthalate film dielectric d.c. capacitors Part 24: Sectional specification Surface mount fixed tantalum electrolytic capacitors with conductive polymer solid electrolyte (under consideration) Part 25: Sectional spe
30、cification Surface mount fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte (under consideration) All sectional specifications mentioned above do have one or more blank detail specifications being a supplementary document, containing requirements for style, layout and
31、minimum content of detail specifications. EIA-60384-16 Page 3 The QC 301 200 number that appears on the front cover of this publication is the specifica-tion number in the IECQ Quality Assessment System for Electronic Components. The committee has decided that the contents of this publication will r
32、emain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. A bilingual version of this publicat
33、ion may be issued at a later date. EIA-60384-16 Page 4 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c. capacitors 1 General 1.1 Scope This part of IEC 60384 applies to fixed capacitors with metallized electrodes a
34、nd poly-propylene dielectric for use in electronic equipment. These capacitors may have “self-healing properties“ depending on conditions of use. They are mainly intended for use with direct voltage. Capacitors for alternating voltage and pulse applications are not included, but are covered by IEC 6
35、0384-17. The maximum power to be applied is 500 var at 50 Hz and the maximum peak voltage is 2 500 V. Two performance grades of capacitors are covered, Grade 1 for long-life application and Grade 2 for general application. Capacitors for electromagnetic interference suppression are not included, but
36、 are covered by IEC 60384-14. Capacitors for electrical shock hazard protection (covered by IEC 60065) and fluorescent lamp and motor capacitors (covered by IEC technical committee 33, and IEC technical com-mittee 34). 1.2 Object The object of this standard is to prescribe preferred ratings and char
37、acteristics and to select from IEC 60384-1 (1999) the appropriate quality assessment procedures, tests and measur-ing methods and to give general performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring to this sectional spec
38、-ification shall be of equal or higher performance level, because lower performance levels are not permitted. 1.3 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated referenc
39、es, the latest edition of the referenced document (including any amendments) applies. IEC 60063:1963, Preferred number series for resistors and capacitors Amendment 1 (1967) Amendment 2 (1977) IEC 60068-1, Environmental testing. Part 1: General and guidance IEC 60384-1, Fixed capacitors for use in e
40、lectronic equipment Part 1: Generic specification IEC 60384-16-1, Fixed capacitors for use in electronic equipment Part 16: Blank detail speci-fication: Fixed metallized polypropylene film dielectric d.c. capacitors Assessment level E IEC 60410, Sampling plans and procedures for inspection by attrib
41、utes ISO 3, Preferred numbers Series of preferred numbers EIA-60384-16 Page 5 1.4 Information to be given in a detail specification Detail specifications shall be derived from the relevant blank detail specification. Detail specifications shall not specify requirements inferior to those of the gener
42、ic, sectional or blank detail specification. When more severe requirements are included, they shall be listed in 1.9 of the detail specification and indicated in the test schedules, for example by an asterisk. NOTE The information given in 1.4.1 may for convenience, be presented in tabular form. The
43、 following information shall be given in each detail specification and the values quoted shall preferably be selected from those given in the appropriate clause of this sectional speci-fication. 1.4.1 Outline drawing and dimensions There shall be an illustration of the capacitor as an aid to easy re
44、cognition and for compari-son of the capacitor with others. Dimensions and their associated tolerances, which affect interchangeability and mounting, shall be given in the detail specification. All dimensions shall preferably be stated in millimetres. Normally, the numerical values shall be given fo
45、r the length of the body, the width and height of the body and the wire spacing, or for cylindrical types, the body diameter, and the length and diameter of the terminations. When necessary, for example when a number of items (ca-pacitance values/voltage ranges) are covered by a detail specification
46、, the dimensions and their associated tolerances shall be placed in a table below the drawing. When the configuration is other than described above, the detail specification shall state such dimensional information as will adequately describe the capacitor. When the capacitor is not designed for use
47、 on printed boards, this shall be clearly stated in the detail specification 1.4.2 Mounting The detail specification shall specify the method of mounting to be applied for normal use and for the application of the vibration and the bump or shock tests. The capacitors shall be mounted by their normal
48、 means. The design of the capacitor may be such that special mount-ing fixtures are required in its use. In this case, the detail specification shall describe the mounting fixtures and they shall be used in the application of the vibration and bump or shock tests. 1.4.3 Ratings and characteristics T
49、he ratings and characteristics shall be in accordance with the relevant clauses of this speci-fication, together with the following: 1.4.3.1 Rated capacitance range See 2.2.1. NOTE When products approved to the detail specification may have different ranges, the following statement should be added: “The range of values available in each voltage range is given in IEC QC 001005. 1.4.3.2 Particular characteristics Additional characteristics may be listed, when they are considered necessary to specify ade-quately the component for design and application p
