1、 EIA STANDARD Fixed Capacitors for Use in Electronic Equipment Part 4: Sectional Specification Aluminium Electrolytic Capacitors with Solid (MnO2) and Non-Solid Electrolyte EIA-60384-4 (IEC 60384-4:2007, IDT) October 2014 ANSI/EIA-60384-4-2014 Approved: October 6, 2014 EIA-60384-11 EIA-60384-4NOTICE
2、 EIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the
3、 proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications
4、 preclude their voluntary use by those other than ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not a
5、ssume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is identical (IDT) with the International Standard IEC Publication 60384-4:2007: Fixed Capacitors for Use in Electronic Equipment Part 4: Sectional S
6、pecification Aluminium Electrolytic Capacitors with Solid (MnO2) and Non-Solid Electrolyte. This document is the EIA Standard EIA-60384-4 2014: Fixed Capacitors for Use in Electronic Equipment Part 4: Sectional Specification Aluminium Electrolytic Capacitors with Solid (MnO2) and Non-Solid Electroly
7、te. The text, figures and tables of IEC 60384-4:2007 are used in this Standard with the consent of the IEC and the American National Standards Institute (ANSI). These materials are subject to copyright claims of IEC and ECIA. No part of this publication may be reproduced in any form, including an el
8、ectronic retrieval system, without the prior written permission of ECIA. All requests pertaining to EIA-60384-4 2014: Fixed Capacitors for Use in Electronic Equipment Part 4: Sectional Specification Aluminium Electrolytic Capacitors with Solid (MnO2) and Non-Solid Electrolyte should be submitted to
9、ECIA at the address below. The IEC copyrighted material has been reproduced with permission from ANSI. The IEC Foreword and Introduction are not part of the requirements of this standard but are included for information purposes only. This Standard does not purport to address all safety problems ass
10、ociated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5284, formulated under
11、the cognizance of the P-2.5 Committee on EIA Solid Electrolytic Capacitors Standards and given final approval by the Steering Committee for Passive Electronic Components Standards (S-1). Published by Electronic Components Industry Association 2014 Standards any IEC National Committee interested in t
12、he subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditi
13、ons determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC Nation
14、al Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way
15、in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC P
16、ublication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ens
17、ure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of
18、any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the re
19、ferenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. Int
20、ernational Standard IEC 60384-4 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. This fourth edition cancels and replaces the third edition published in 1998 and its amendment 1 (2000). This edition constitutes a minor revision related to tables, fi
21、gures and references. This bilingual version, published in 2008, corresponds to the English version. It includes Corrigendum 1 (2007). EIA-60384-4 Page 2 The text of this standard is based on the following documents: CDV Report on voting 40/1759/CDV 40/1819/RVCFull information on the voting for the
22、approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The French version of this standard has not been voted upon. The QC number that appears on the front cover of this publica
23、tion is the specification number in the IEC Quality Assessment System for Electronic Components (IECQ). The list of all parts of the IEC 60384 series, under the general title Fixed capacitors for use in electronic equipment, can be found on the IEC website. The committee has decided that the content
24、s of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. EIA-6038
25、4-4 Page 3 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 4: Sectional specification Aluminium electrolytic capacitors with solid (MnO2) and non-solid electrolyte 1 General 1.1 Scope This part of IEC 60384 applies to aluminium electrolytic capacitors with solid (MnO2) and non-solid electrolyt
26、e primarily intended for d.c. applications for use in electronic equipment. It covers capacitors for long-life applications and capacitors for general-purpose applications. Capacitors for special-purpose applications may need additional requirements. Capacitors for fixed surface mount aluminium elec
27、trolytic capacitors are not included but they are covered by IEC 60384-18. 1.2 Object The principal object of this standard is to prescribe preferred ratings and characteristics and to select from IEC 60384-1 the appropriate quality assessment procedures, tests and measuring methods and to give gene
28、ral performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring to this sectional specification shall be of equal or higher performance level, because lower performance levels are not permitted. 1.3 Normative references The foll
29、owing referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60063, Preferred number series for resistors and capa
30、citors IEC 60068-1, Environmental testing Part 1: General and guidance IEC 60068-2-17, Environmental testing Part 2-17: Tests Test Q: Sealing IEC 60068-2-54, Environmental testing Part 2-54: Tests Test Ta: Solderability testing of electronic components by the wetting balance method IEC 60384-1:1999,
31、 Fixed capacitors for use in electronic equipment Part 1: Generic specification EIA-60384-4 Page 4 IEC 60384-4-1, Fixed capacitors for use in electronic equipment Part 4-1: Blank detail specification Fixed aluminium electrolyte capacitors with non-solid electrolyte Assessment level EZ IEC 60384-4-2,
32、 Fixed capacitors for use in electronic equipment Part 4-2: Blank detail specification Fixed aluminium electrolyte capacitors with solid (MnO2) electrolyte Assessment level EZ IEC 60410:1973, Sampling plans and procedures for inspection by attributes ISO 3, Preferred numbers Series of preferred numb
33、ers 1.4 Information to be given in a detail specification Detail specifications shall be derived from the relevant blank detail specification. Detail specifications shall not specify requirements inferior to those of the generic, sectional or blank detail specification. When more severe requirements
34、 are included, they shall be listed in 1.9 of the detail specification and indicated in the test schedules, for example, by an asterisk. NOTE The information given in 1.4.1 may, for convenience, be presented in tabular form. The following information shall be given in each detail specification and t
35、he values quoted shall preferably be selected from those given in the appropriate clause of this sectional specification. 1.4.1 Outline drawing and dimensions There shall be an illustration of the capacitor as an aid to easy recognition and for comparison of the capacitor with others. Dimensions and
36、 their associated tolerances, which affect interchangeability and mounting, shall be given in the detail specification. All dimensions shall preferably be stated in millimeters; however, when the original dimensions are given in inches, the converted metric dimensions in millimetres shall be added.
37、Normally, the numerical values shall be given for the length of the body, the width and height of the body and the wire spacing, or for cylindrical types, the body diameter, and the length and diameter of the terminations. When necessary, for example, when a number of items (capacitance values/volta
38、ge ranges) are covered by a detail specification, the dimensions and their associated tolerances shall be placed in a table below the drawing. When the configuration is other than described above, the detail specification shall state such dimensional information as will adequately describe the capac
39、itor. When the capacitor is not designed for use on printed boards, this shall be clearly stated in the detail specification. 1.4.2 Mounting The detail specification shall specify the method of mounting to be applied for normal use and for the application of the vibration and the bump or shock tests
40、. The capacitors shall be mounted by their normal means. The design of the capacitor may be such that special mounting fixtures are required in its use. In this case, the detail specification shall describe the mounting fixtures and they shall be used in the application of the vibration and bump or
41、shock tests. 1.4.3 Ratings and characteristics The ratings and characteristics shall be in accordance with the relevant clauses of this specification, together with the following. EIA-60384-4 Page 5 1.4.3.1 Rated capacitance range See 2.2.1. NOTE When products approved to the detail specification ha
42、ve different ranges, the following statement should be added: “The range of values available in each voltage range is given in IEC QC 001005.“. EIA-60384-4 Page 6 1.4.3.2 Particular characteristics Additional characteristics may be listed when they are considered necessary to specify adequately the
43、component for design and application purposes. 1.4.3.3 Soldering The detail specification shall prescribe the test methods, severities and requirements applicable for the solderability and the resistance to soldering heat test. 1.4.4 Marking The detail specification shall specify the content of the
44、marking on the capacitor and on the package. Deviations in 1.6 of this sectional specification shall be specifically stated. 1.5 Terms and definitions For the purposes of this document, the following terms and definitions, in addition to the applicable terms and definitions of IEC 60384-1, apply. 1.
45、5.1 capacitance of an electrolytic capacitor capacitance of an equivalent circuit having capacitance and resistance in series measured with alternating current approximately sinusoidal waveform at a specified frequency 1.5.2 long-life grade capacitors capacitors intended for applications where a hig
46、h degree of stability of characteristics over a long life is essential. The materials are chosen and the manufacture carried out so that improved performance is obtained with consequent increase in life 1.5.3 general-purpose grade capacitors capacitors intended for applications where the high perfor
47、mance level of long-life grade capacitors is not required 1.5.4 reverse voltage (for polar capacitors only) voltage applied to the capacitor terminals in the reverse polarity direction 1.6 Marking According to 2.4 of IEC 60384-1, with the following details. 1.6.1 The information given in the marking
48、 is normally selected from the following list; the relative importance of each item is indicated by its position in the list: a) rated capacitance; b) rated voltage (d.c. voltage may be indicated by the symbol: or ); c) category voltage and category temperatures (for long-life grade capacitors only)
49、; d) polarity of the terminations: for multi-section capacitors, the rated capacitance and rated voltage of the sections connected to each termination shall be shown in an unambiguous way. The termination of a capacitor section which is intended for direct connection to the rectifier (so-called reservoir section) shall be marked with the number 1 or with the colour red; e) tolerance on rated capacitance; f) reference to the grade (for long-life grade capacitors only). The abbreviation LL may be used for marking purposes; EIA-60
