EN 10152-2017 en Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions《冷成型用电解镀锌扁平冷轧材-交货技术条件》.pdf

上传人:rimleave225 文档编号:705209 上传时间:2019-01-03 格式:PDF 页数:24 大小:1.83MB
下载 相关 举报
EN 10152-2017 en Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions《冷成型用电解镀锌扁平冷轧材-交货技术条件》.pdf_第1页
第1页 / 共24页
EN 10152-2017 en Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions《冷成型用电解镀锌扁平冷轧材-交货技术条件》.pdf_第2页
第2页 / 共24页
EN 10152-2017 en Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions《冷成型用电解镀锌扁平冷轧材-交货技术条件》.pdf_第3页
第3页 / 共24页
EN 10152-2017 en Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions《冷成型用电解镀锌扁平冷轧材-交货技术条件》.pdf_第4页
第4页 / 共24页
EN 10152-2017 en Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions《冷成型用电解镀锌扁平冷轧材-交货技术条件》.pdf_第5页
第5页 / 共24页
点击查看更多>>
资源描述

1、BS EN 10152:2017Electrolytically zinc coatedcold rolled steel flat productsfor cold forming Technicaldelivery conditionsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 10152:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of

2、 EN 10152:2017.It supersedes BS EN 10152:2009 which is withdrawn . The UK participation in its preparation was entrusted to Technic -al Committee ISE/109, Coated and Uncoated Flat Products to be Used for Cold Forming.A list of organizations represented on this committee can be obtained on request to

3、 its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017. Published by BSI Standards Limited 2017ISBN 978 0 580 91104 0 ICS 77.140.50 Compliance with a British Sta

4、ndard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 10152:2017EUROPEAN STANDARD NORME EUROPENNE EU

5、ROPISCHE NORM EN 10152 January 2017 ICS 77.140.50 Supersedes EN 10152:2009English Version Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions Produits plats en acier, lamins froid, revtus de zinc par voie lectrolytique pour formage froid - Co

6、nditions techniques de livraison Elektrolytisch verzinkte kaltgewalzte Flacherzeugnisse aus Stahl zum Kaltumformen - Technische Lieferbedingungen This European Standard was approved by CEN on 21 November 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate

7、the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standa

8、rd exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the natio

9、nal standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slov

10、akia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any mean

11、s reserved worldwide for CEN national Members. Ref. No. EN 10152:2017 EBS EN 10152:2017EN 10152:2017 (E) 2 Contents PageEuropean foreword . 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 6 4 Classification and designation 6 4.1 Classification . 6 4.2 Designation 6 5 Information to be

12、 supplied by the purchaser . 7 5.1 Mandatory information 7 5.2 Options 8 6 Requirements . 8 6.1 General 8 6.2 Steelmaking and manufacturing processes . 9 6.3 Deoxidation . 9 6.4 Chemical composition . 9 6.5 Delivery condition 9 6.6 Choice of properties . 9 6.7 Mechanical properties . 9 Table 1 Chemi

13、cal composition and mechanical properties of electrolytically zinc coated mild steel flat products a. 106.8 Stretcher strain marks . 12 6.9 Coatings . 12 Table 2 Electrolytic zinc coatings (see also 6.9.4 and 6.9.5) 13 6.10 Surface characteristics . 13 6.10.1 General . 13 6.10.2 Surface quality. 13

14、6.10.3 Surface finish . 13 6.11 Surface treatment (surface protection) . 14 Table 3 Surface treatment . 14 6.12 Applications . 15 6.12.1 Welding 15 6.12.2 Painting 15 6.12.3 Forming 15 6.13 Mass, tolerances on dimensions and shape 15 7 Inspection . 15 7.1 Types of inspection and inspection documents

15、 15 7.2 Test units . 16 7.3 Tests to be carried out 16 7.4 Sampling 16 7.5 Test methods . 16 7.5.1 Tensile test . 16 BS EN 10152:2017EN 10152:2017 (E) 3 7.5.2 Plastic strain ratio and hardening exponent 16 7.5.3 Coating mass . 16 7.6 Retests 17 8 Marking 17 9 Packing . 17 10 Storage and transportati

16、on . 17 Annex A (normative) Reference method for determination of the zinc coating mass . 18 A.1 Principle . 18 A.2 Reagent and preparation of the solution . 18 A.2.1 Reagent . 18 A.2.2 Preparation of the solution . 18 A.3 Apparatus 18 A.4 Procedure 18 Bibliography . 19 BS EN 10152:2017EN 10152:2017

17、 (E) 4 European foreword This document (EN 10152:2017) has been prepared by Technical Committee ECISS/TC 109 “Coated and uncoated flat products to be used for cold forming”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by

18、publication of an identical text or by endorsement, at the latest by July 2017, and conflicting national standards shall be withdrawn at the latest by July 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be hel

19、d responsible for identifying any or all such patent rights. This document supersedes EN 10152:2009. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,

20、Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the Un

21、ited Kingdom. BS EN 10152:2017EN 10152:2017 (E) 5 1 Scope This European Standard specifies requirements for continuously electrolytic (or produced with an alternative process on cold rolled finish substrate) zinc coated cold rolled flat products of low carbon steels suitable for cold forming accordi

22、ng to Table 1 in rolled widths 600 mm and thicknesses from 0,35 mm up to below and including 3 mm, delivered as strip (in coil form), sheet, slit strip or cut lengths obtained from slit strip or sheet. NOTE 1 This European Standard can also be applied to continuously electrolytic zinc coated flat pr

23、oducts of: a) steels according to EN 10139 (cold rolled strip in rolled widths 600 mm),b) steels normally characterized by minimum yield strength or minimum tensile strength values inaddition to formability parameters, e.g. 1) steels with high yield strength and improved formability according to EN

24、10268 (cold rolled flat products), 2) multiphase steels (cold rolled or hot rolled) according to EN 10338, 3) steels for construction according to national or regional standards (see e.g. DIN 1623). NOTE 2 By agreement at the time of enquiry and order this European Standard can be applied to continu

25、ously electrolytic zinc coated hot-rolled steel flat products (e.g. according to EN 100251 and 2, EN 10111, EN 101491 to EN 101493, etc.). NOTE 3 As the mass of the zinc coating applied is relatively small, the material is not intended to withstand outside exposure without further chemical treatment

26、 and painting. NOTE 4 The products covered by this European Standard can be used as substrates for organic coated flat products specified in EN 10169 for building and general engineering applications. 2 Normative references The following documents, in whole or in part, are normatively referenced in

27、this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10020:2000, Definition and classification of grades of steel EN 10021:2006, Gene

28、ral technical delivery conditions for steel products EN 10027-1, Designation systems for steels - Part 1: Steel names EN 10027-2, Designation systems for steels - Part 2: Numerical system EN 10051, Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tole

29、rances on dimensions and shape EN 10079:2007, Definition of steel products EN 10131, Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimensions and shape BS EN 10152:2017EN 10152:2017 (E) 6 E

30、N 10204:2004, Metallic products - Types of inspection documents ISO 10113, Metallic materials Sheet and strip Determination of plastic strain ratio ISO 10275, Metallic materials Sheet and strip Determination of tensile strain hardening exponent EN ISO 6892-1:2009, Metallic materials - Tensile testin

31、g - Part 1: Method of test at room temperature (ISO 6892-1:2009) 3 Terms and definitions For the purposes of this document the terms and definitions given in EN 10020:2000, EN 10021:2006, EN 10079:2007, EN 10204:2004 and the following apply. 3.1 electrolytic zinc coating (ZE) application of a zinc c

32、oating by electrolysis on a suitably prepared steel surface from an aqueous zinc salt solution by the use of an electric current Note 1 to entry Flat products can have a zinc coating on one or both surfaces. If both surfaces are zinc coated, a different coating thickness can be applied on each side

33、(this process being referred to as differential zinc coating). 4 Classification and designation 4.1 Classification The steel grades specified in this European Standard are classified in accordance with EN 10020:2000 as non-alloy quality steels (DC01, DC03, DC04, DC05) and alloy quality steels (DC06,

34、 DC07) and by their increasing suitability for cold forming as follows: DC01: drawing quality; DC03: deep drawing quality; DC04, DC05: special deep drawing quality; DC06: extra deep drawing quality; DC07: super deep drawing quality. 4.2 Designation 4.2.1 The steel names are allocated in accordance w

35、ith EN 10027-1. The steel numbers are allocated in accordance with EN 10027-2. 4.2.2 The products covered by this document shall be designated as follows in the given order: 1) Type of product (e.g. strip, sheet, cut length); 2) Number of this European Standard (EN 10152); 3) Steel name or steel num

36、ber and symbol for the type of electrolytic coating (see Table 1); BS EN 10152:2017EN 10152:2017 (E) 7 4) Numbers denoting the nominal coating thickness on each surface (e.g. 50/50 = nominal coating thickness of 5,0 m on each side, see Table 2 and 6.9.2); 5) Letters A or B indicating the surface qua

37、lity (see 6.10.2); 6) Letters denoting the surface treatment (see 6.11 and Table 3). EXAMPLE 1 Designation of strip made of steel DC03+ZE (1.0347+ZE), electrolytically zinc coated with a nominal thickness of 5,0 m on each surface (50/50), surface quality A, surface treatment phosphated (P): Strip EN

38、 10152 +ZE50 DC03/50-A-P or Strip EN 101521.0347+ZE50/50-A-P EXAMPLE 2 Designation of sheet made of steel DC05+ZE (1.0312+ZE), electrolytically zinc coated with a nominal thickness of 7,5 m on one surface and of 2,5 m on the other surface (75/25), surface quality B, surface treatment phosphated and

39、oiled (PO): Sheet EN 10152 +ZE75 DC05/25-B-PO or Sheet EN 101521.0312+ZE75/25-B-PO 4.2.3 Where appropriate, additional information to the designation as specified in 4.2.2 shall be given to describe clearly the delivery requirements (see Clause 5). 5 Information to be supplied by the purchaser 5.1 M

40、andatory information The following information shall be supplied by the purchaser at the time of enquiry and order: a) complete designation (see 4.2.2); b) nominal dimensions (thickness, width and, in the case of sheet and cut lengths, length); c) quantity; d) limiting mass and sizes of the coils an

41、d individual bundles of sheets; e) surface quality and surface finish (see 6.10); f) type of surface treatment (see 6.11 and Table 3). BS EN 10152:2017EN 10152:2017 (E) 8 5.2 Options A number of options are specified in this document and listed below; if the purchaser does not indicate a wish to imp

42、lement any of these options, the products shall be supplied in accordance with the basis specification of this document (see 5.1): 1) Delivery of hot rolled products (see NOTE 2 to Clause 1);2) Use of substrates not specified in Table 1 (see 6.1);3) Steelmaking and manufacturing processes (see 6.2);

43、4) Non-skin passed products (see 6.5);5) Products supplied suitable for the manufacture of a specific part (see 6.6);6) Delivery of several steel grades as alloy steels (see Table 1, footnote f);7) Differential coatings (see 6.9.4);8) One-side coated products (see 6.9.5);9) Maximum coating mass per

44、product surface (see 6.9.6);10) Quality of the uncoated surface for one-side coated products and/or testing of both surfaces (see6.10.2.1);11) Range for surface roughness Ra (see 6.10.3);12) Specification of dimensional tolerances different from those in EN 10131 or EN 10051, respectively(see 6.13.2

45、);13) Type of inspection and inspection document to be delivered (see 7.1.1 to 7.1.3);14) Certificate of compliance with order (see 7.1.2);15) determination of the tensile properties by calculation (see 7.1.2);16) Marking by branding (see 8.2);17) Requirements for packaging (see Clause 9).6 Requirem

46、ents 6.1 General The requirements according to 6.2 to 6.5 and 6.13 apply to products made of the steel grades given in Table 1. For other steels used as substrate for electrolytically deposited coatings of zinc the requirements shall be based on the appropriate quality standard for the non-coated st

47、eel product. BS EN 10152:2017EN 10152:2017 (E) 9 6.2 Steelmaking and manufacturing processes Unless otherwise agreed at the time of enquiry and order, the steelmaking and manufacturing processes are left to the discretion of the manufacturer. The purchaser shall be informed of these processes, if re

48、quired. 6.3 Deoxidation The method of deoxidation shall be in accordance with that specified in Table 1. 6.4 Chemical composition The chemical composition based on cast analysis shall be as given in Table 1. 6.5 Delivery condition The steel substrates are normally supplied in the skin-passed conditi

49、on. By agreement at the time of enquiry and order non skin-passed products may be supplied. 6.6 Choice of properties The products covered by this document shall comply with the requirements of Table 1. By agreement at the time of enquiry and order, they can be supplied with suitability for manufacturing a specific part. In this case a specific proportion exceeding the reject tolerances may be agreed and acceptance on the basis of mechanical properties is not applicable. 6.7 Mechanical properties 6.7.1 The mechanical properties are given

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1