1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 10264-4:2012Steel wire and wire products Steel wire for ropesPart 4: Stainless steel wireBS EN 10264-4:2012 BRITISH STANDARDNational forewordThis British Standard is the UK
2、 implementation of EN 10264-4:2012. It supersedes BS EN 10264-4:2002, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e I S E / 1 0 6 , W i r e R o d a n d W i r e .A list of organizations represented on this committee can be obtained on
3、request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012 ISBN 978 0 580 62607 4 ICS 77.140.20; 77.140.65 Compliance with a British Standard cannot confer
4、 immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 10264-4:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10264-4 Jan
5、uary 2012 ICS 77.140.65; 77.140.20 Supersedes EN 10264-4:2002English Version Steel wire and wire products - Steel wire for ropes - Part 4: Stainless steel wire Fils et produits trfils en acier - Fils pour cbles - Partie 4: Fils trfils en acier inoxydable Stahldraht und Drahterzeugnisse - Stahldraht
6、fr Seile - Teil 4: Draht aus nichtrostendem Stahl This European Standard was approved by CEN on 19 November 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any a
7、lteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language
8、made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Es
9、tonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALIS
10、ATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10264-4:2012: EBS EN 10264-4:2012EN 10264-4:2012 (E) 2 Contents Page Foreword 31 Scope 4
11、2 Normative references 43 Designation of product .44 General conditions of manufacture .44.1 Main steel grades and characteristic applications .44.2 Chemical composition 54.3 Surface condition.55 Characteristics and requirements 65.1 Tensile strength .65.2 Diameter tolerances 65.3 Ductility .75.4 Ma
12、gnetic permeability .76 Test methods 76.1 General 76.2 Dimension of wire 76.3 Tensile test .76.4 Reverse bend test 76.5 Wrapping test .76.6 Tensile test on knotted wire .86.7 Magnetic permeability .8BS EN 10264-4:2012EN 10264-4:2012 (E) 3 Foreword This document (EN 10264-4:2012) has been prepared by
13、 Technical Committee ECISS/TC 106 “Wire rod and wires”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2012, and conflicting national standards sha
14、ll be withdrawn at the latest by July 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10264-4:2002.
15、This European Standard for wire for ropes is made up of the following parts: Part 1: General requirements Part 2: Cold drawn non alloy steel wire for ropes for general applications Part 3: Round and shaped non alloyed steel wire for high duty applications Part 4: Stainless steel wire This European S
16、tandard has been technically revised to incorporate the following changes: a) clarification has been given in Table 2 “Chemical analysis in % by mass“ because some values are ranges. A note has also been added in order to mention that other steel grades can be agreed between purchaser and supplier;
17、b) modification has been made on the maximum value for the tensile strength (see 5.1); c) the nominal diameter and the minimum tensile strength given in Table 3 “Tensile strength requirements“ have been changed; d) a note has been added to allow other diameters or tensile strength than those given i
18、n Table 3, subject to an agreement between purchaser and supplier; e) the ranges of nominal diameter given in Table 4 “Diameter tolerances“ have been clarified. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement t
19、his European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerla
20、nd, Turkey and the United Kingdom. BS EN 10264-4:2012EN 10264-4:2012 (E) 4 1 Scope This part of this European Standard specifies the characteristics of stainless steel wire for the manufacture of ropes that are exposed to corrosion and in some cases to a moderate temperature. This part of this Europ
21、ean Standard specifies the following for stainless steel wire for ropes: dimensional tolerances; mechanical characteristics; requirements relating to the chemical composition of the stainless steel wire; conditions to be satisfied by any coating. 2 Normative references The following referenced docum
22、ents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10088-3, Stainless steels Part 3: Technical delivery conditions for semi-fin
23、ished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes EN 10095, Heat resisting steels and nickel alloys EN 10218-1, Steel wire and wire products General Part 1: Test methods EN 10264-1, Steel wire and wire products Steel wire for ropes Part
24、 1: General requirements ASTM A342, Standard Test Methods for Permeability of Feebly Magnetic Materials 3 Designation of product The designation of the product is based on the nominal diameter, chemical composition and minimum tensile strength of the wire. EXAMPLE Stainless steel wire for rope, diam
25、eter 1,5 mm - grade X4CrNi18-12 - strength 1 450 MPa. Designation: Wire for rope EN 10264-41,5X4CrNi18-121 450. NOTE The grade of steel can be designated numerically, see Table 1. 4 General conditions of manufacture 4.1 Main steel grades and characteristic applications The grades given in Table 1 ar
26、e widely used mainly in accordance with EN 10088-3 and EN 10095 with requirements as specified in this part of EN 10264. However, for other specific applications other steel grades specified in EN 10088-3 or EN 10095 may be used with requirements to be agreed between the parties. Table 1 gives an in
27、formative indication of characteristic applications of the mentioned steel grades. BS EN 10264-4:2012EN 10264-4:2012 (E) 5 Table 1 Main steel grades and characteristic applications Grades of steel Application Steel number Steel name 1.4301 X5CrNi18-10 For general use in a corrosive environment 1.431
28、0 X10CrNi18-8 As 1.4301 for general use for greater mechanical strength 1.4401 X5CrNiMo17-12-2 For highly corrosive environment particularly in marine atmosphere 1.4303 X4CrNi18-12 For low permeability requirements 1.4841 X15CrNiSi25-21 For ropes also subjected to a moderate temperature 4.2 Chemical
29、 composition In accordance with EN 10088-3 and EN 10095, the chemical composition of the stainless steels shall comply with Table 2. Table 2 Chemical analysis in % by mass Grades of steel C Si max. Mn max. P max. S max. Cr Mo Ni N Steel numberSteel name 1.4301 X5CrNi18-10 0,07 1,00 2,00 0,045 0,015
30、17,00 to19,50 8,00 to10,50 0,11 1.4310 X10CrNi18-8 0,05 to0,15 2,00 2,00 0,045 0,015 16,00 to19,00 0,80 6,00 to 9,50 0,11 1.4401 X5CrNiMo17-12-2 0,07 1,00 2,00 0,045 0,015 16,50 to18,50 2,00 to 2,50 10,00 to 13,00 0,11 1.4303 X4CrNi18-12 0,06 1,00 2,00 0,045 0,015 17,00 to19,00 11,00 to 13,00 0,11 1
31、.4841 X15CrNiSi25-21 0,20 1,50 to 2,50 2,00 0,045 0,030 24,00 to 26,00 19,00 to 22,00 0,11 NOTE Other steel grades can be agreed between purchaser and supplier. 4.3 Surface condition Stainless steel wire for ropes shall be supplied either matt (dry drawn) or shiny (surface condition achieved either
32、by polishing or by wet drawing). If a particular appearance is required, it shall be stipulated at the time of enquiry and order. As an indication, wire of diameter lower than 0,50 mm is normally wet drawn and supplied shiny while wire with a diameter greater than 1,00 mm is commonly dry drawn and s
33、upplied matt. For intermediate sizes there is no preference and it will be pending of the manufacturer. BS EN 10264-4:2012EN 10264-4:2012 (E) 6 5 Characteristics and requirements 5.1 Tensile strength The wire is characterized by a minimum tensile strength. The minimum tensile strength depends on the
34、 steel grade and the diameter of the wire. Table 3 specifies the minimum tensile strength for each steel grade. The maximum value shall not exceed the minimum value plus 20 %. Table 3 Tensile strength requirements Nominal diameter d mm Minimum tensile strength a MPa b1.4301 1.4310 1.4303 1.4401 1.48
35、41 LT cNT dd 0,20 2 050 2 200 1 600 1 725 1 700 0,20 d 0,30 2 000 2 150 1 575 1 700 1 650 0,30 d 0,40 1 950 2 100 1 550 1 675 1 600 0,40 d 0,50 1 900 2 050 1 550 1 650 1 575 0,50 d 0,65 1 850 2 000 1 525 1 625 1 575 0,65 d 0,80 1 800 1 950 1 525 1 600 1 550 0,80 d 1,00 1 750 1 900 1 500 1 575 1 550
36、1,00 d 1,25 1 700 1 850 1 475 1 550 1 525 1,25 d 1,50 1 650 1 800 1 450 1 500 1 500 1,50 d 1,75 1 600 1 750 1 425 1 450 1 475 1,75 d 2,00 1 550 1 700 1 400 1 400 1 450 2,00 d 2,50 1 500 1 650 1 350 1 350 1 400 2,50 d 3,00 1 450 1 600 1 300 1 300 1 350 NOTEOther diameters or tensile strength can be a
37、greed between purchaser and supplier.a For ropes for specific applications, lower strengths may be requested. b1 MPa = 1 N/mm2. cLow level of tensile strength. dNormal level of tensile strength. 5.2 Diameter tolerances The diameter measured shall comply with the tolerances specified in Table 4. The
38、out of roundness shall not be greater than half the tolerance on diameter. BS EN 10264-4:2012EN 10264-4:2012 (E) 7 Table 4 Diameter tolerances Dimensions in millimetres Nominal diameter d Tolerance ()0,12 d 0,22 0,006 0,22 d 0,37 0,008 0,37 d 0,65 0,010 0,65 d 1,01 0,015 1,01 d 1,78 0,020 1,78 d 2,7
39、8 0,025 2,78 d 3,00 0,030 5.3 Ductility Because of the specific nature of this material and its deformation structure (by drawing), conventional ductility tests show a wide spread. When they are required, the following ductility tests shall be carried out: reverse bending test, tensile strength test
40、 on knotted wire or wrapping test. The parties shall agree upon the required ductility tests and on the minimum required results. 5.4 Magnetic permeability When the grade X4CrNi18-12 (1.4303) is required with a very low permeability (non-magnetic), the magnetic permeability shall be less than 1,05.
41、The grade X4CrNiMo17-12-2 (1.4401) may also be requested with low permeability. In this case, the requirements shall be agreed between the parties. 6 Test methods 6.1 General Tests shall be carried out in accordance with EN 10218-1 and EN 10264-1 with the following observations. 6.2 Dimension of wir
42、e The diameter of the wire shall be measured with a micrometer with an accuracy of at least 0,001 mm for dimensions below 0,65 mm. For larger wire, an accuracy of 0,01 mm is acceptable. 6.3 Tensile test The tensile test shall be carried out in accordance with EN 10264-1. 6.4 Reverse bend test The re
43、verse bend test shall be carried out in accordance with EN 10218-1. 6.5 Wrapping test When coiled for 8 turns around a mandrel of equal diameter to the wire, the wire shall show no signs of breaking; the test shall be carried out in accordance with EN 10218-1. BS EN 10264-4:2012EN 10264-4:2012 (E) 8
44、 6.6 Tensile test on knotted wire For diameters 0,50 mm, the tensile test on knotted wire shall be carried out in accordance with EN 10218-1. The strength is then measured on a wire in which 1 simple knot has been made. This strength is expressed as a percentage of the tensile strength of the unknot
45、ted wire. 6.7 Magnetic permeability Magnetic permeability shall be measured in accordance with ASTM A342 method 4 in a field of 500 to 1 000 Oersted. This page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publicat
46、ions, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldw
47、ideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to impr
48、ove the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please noti
49、fy BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of stan
