1、STD=BSI BS EN 1063-ENGL 2000 m Lb24669 0860404 TTL I BRITISH STANDARD Glass in building - Security glazing - Testing and classification of resistance against bullet attack The European Standard EN 1063:1999 has the status of a British Standard ICs 13.310; 81.040.20 NO COPYING WITHOUT BSI PERMISSION
2、EXCEPT AS PERMIITED BY COPYRIGHT LAW 5s EN .063:2000 STD=BSI BS EN LOb3-ENGL 2000 Lb24bb9 0860405 938 = been prepared under the direction of the Sector Committee for Building and Civil Engineering, was published under the authorily of the Standards Committee and comes into effect on 15 July Zoo0 Amd
3、. No. 0 BSI 07-2000 ISBN O 580 36105 5 BS EN 1063:2000 Date Comments National foreword This British Standard is the official Engiish language version of EN 1063.1999. The UK participation in its preparation was entrusted by Technical Committee B/520, Glass and glazing in building, to Subcommittee W5
4、20/3, Security glazing, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible European committee any enquiries on the - monitor related international and European developments and promuigate interpretation, or proposals for change, and keep the UK inte
5、ress informed; them in the UK A list of organizations represented on this subcommittee can be obtained on request to its secretary. This British Standard supersedes BS 5051-1: 1988 immediately for the testing and classification of glass and glasdplastics composites. BS 5051-1 wil however remain avai
6、lable for the testing and Classification of plastics glazing sheet materiais until a corresponding British Standard is published for these products. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Stan
7、dards Catalogue under the section entitled “International Standards Correspondence Index“, or by using the “Find“ facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a conkact. Users of British standards are responsible f
8、or their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN titie page, pages 2 to 9 and a back cover. The BSI copyright notice displayed in this docu
9、ment indicates when the document was last issued. STDWBSI BS EN LOb3-ENGL 2000 = Lb24bb9 08b040b 874 H EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1063 November 1999 ICs 13.310; 81.040.20 English version Glass in building - Security glazing - Testing and classification of resistance against
10、 bullet attack Verre dans la construction -Vitrage de scurite - Mise essai et classification de la rsistance lattaque par balle Glas im Bauwesen - Sicherheitssonderverglasung - Prfverfahren und Klasseneinteilung fr den Widerstand gegen Beschu This European Standard was approved by CEN on 16 April 19
11、99. CEN members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this Europmn Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning sich national standards may be obtained o
12、n application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by tmslation under the responsibility of a CEN member into its own language and notified to the Central Secretariat
13、has the same status as he official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMI
14、TTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Central Secretariat: rue de Stassart, 36 B-1050 Brussels O 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1063:1999 E STD-BSI BS EN LOb3-E
15、NGL 2000 m Lb24bb9 08b0407 700 m Page 2 EN 1063:1999 Content Page Foreword 3 1 2 3 4 5 6 7 7.1 7.2 8 9 Scope . 3 Normative references . _ . 3 Definitions . 4 Classification of the levels of bullet-resistance and test conditions 4 Test pieces for type testing 6 Performance requirements ._ . 6 Test me
16、thod . 7 Apparatus . 7 Test performance . 8 Report 9 Marking . 9 (o BSI 07-2000 STD-BSI BS EN 1063-ENGL 2000 1bZ4bb7 0860408 b43 Page 3 EN 1063:1999 Foreword This European Standard has been prepared by Technical Committee CENEC 129 “Glass in building“, the secretariat of which is held by IBN. This E
17、uropean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2000, and conflicting national standards shall be withdrawn at the latest by May 2000. According to the CENKENELEC Internal Regulations, the national
18、standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. The ma
19、in requirement for bullet-resistant glazing is to prevent the passage of projectiles from various types of weapon. The classification of bullet-resistance of glazing in this standard is a technical classification, based on common weapons and ammunition, in order of attacking power. As the variety of
20、 weapons and ammunition does not allow them all to be taken into account, a selection had to be made that covers most weapons and ammunition. The choice of bullet-resistant glazing is established by the user for each individual case. 1 Scope This standard specifies performance requirements and test
21、methods for the classification of the bullet- resistance of glass (consisting of one or more layers of glass) and glass/plastic composites. NOTE 1 : The term “bullet-resistant glazing“ applies to products that have the obvious characteristics of glass, but it is understood to include also laminated
22、products of glass and plastics. This standard applies to: -attack by handguns, rifles and shotguns; -glazing in buildings, for interior and exterior use; NOTE 2: For interior use at a temperature of (18 f 5) OC. For exterior use the influence of outside temperature and weathering should be considere
23、d. Any additional requirements should be agreed between the purchaser and the vendor. -the glazing product itself, assuming proper fixing. NOTE 3: The protection provided by bullet-resistant glazing depends not only on the product itself, but also upon the design and fixing of the glass. 2 Normative
24、 references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
25、of these publications apply to this European Standard only when incorporated in it amendment or revision. For undated references, the latest edition of the publication referred to applies. IS0 48 Vulcanized rubbers. Determination of hardness (Hardness between 30 and 85 IRHD) Q BSI 07-2000 STDmBSI BS
26、 EN LOb3-ENGL 2000 Lb24b69 08b0409 583 = Page 4 EN 1063:1999 3 Definitions For the purposes of this European Standard, the following definitions apply. 3.1 of specified weapons and ammunition. buliet-resistant glazing: A security glazing that affords a defined resistance against the firing NOTE: The
27、 glass or plastics component of an unitary bullet-resistant panel may be separated by airspace. 3.2 class. sample: A number of nominally identical glazing units offered for type-testing for a certain 3.3 test piece: One member of the sample prepared for testing. 3.4 detect splinters ejected from the
28、 rear face of the test piece by the impact of the bullet and to determine the risks of injury due to the ejection of these splinters. witness foil: Sheet of aluminium foil as specified in 7.1.3 behind the test piece in order to 3.5 that is designed to face the attack. attack face: The face of a bull
29、et-resistant glazing, marked by the manufacturer andor supplier 3.6 opening from the attack face to the rear face. perforation: Piercing of a test piece by a bullet or by bullet fragments, and/or creation of an 3.7 striking distance: The distance between the centres of two strikes on a test piece. 3
30、.8 the test piece. bullet velocity: The velocity of the bullet measured within 2,5 m in front of the attack face of 3.9 piece. test range: The distance between the muzzle of the firearm and the attack face of the test 4 Classification of the levels of bullet-resistance and test conditions The builet
31、-resistance glazing intended to withstand certain levels of attack shall be classified as BRl, BE, BR3, BR4, BR5, BR6, BR7 according to table 1 and SG1 and SG2 according to table 2. Q BSI 07-2000 STD-BSI BS EN LOb3-ENGL 2000 lb24669 0860430 2T5 I Test conditions I Page 5 EN 1063:1999 Class BRl Table
32、 1: Classification and test requirements for testing the bullet resistance of glazing: hand guns and rifles Type Calibre Type of weapon rifle 0,22 LR L/RN 2,6 *O,l 890 0,l 10,2 *O,l 15,6 *O,l 4,O *o,l 10,OO *0,5 5,OO *0,5 5,OO *0,5 5,OO *0,5 10,OO *0,5 BR6 1 rifle I 7,62 x 51 1 FJ“/PB/SC BR2 BR3 BR4
33、 BR5 handgun 9mmLuger FJ)/RN/SC handgun 0,357 FJ)/CB/SC Magnum handgun 0,44Rem. FJ*)/FN/SC Magnum rifle 5,56 x 45 * FJ)/PB/SCP 1 I I I 1) full steel jacket (plated) 2) full copper alloy jacket 400 *10 430 hl0 440 l0 95 O ?=lo * twist length (178 f 10) mm * twist length (254 * 10) mm 3 3 3 3 L CB FJ
34、FN HC 1 PB RN sc BR7 - lead - coned bullet - full metal jacket bullet - flat nose - steel hard core, mass (3,7 f 0,l) g, hardness more than 63 HRC - pointed bullet - round nose - soft core (lead) rifle 7,62 x 51 * FJ)/PB/HC Mass I t 10,oo 10,oo $i I 0,5 h0,l *0,5 velocity strikes .I) 360 1 3 *10 830
35、 13 *10 distance mm I 120 hl0 120 *IO 120 *10 120 *IO 120 kt10 120 *lo 120 *lo SCPi - soft core (leadj and steel penetrator (type SS109) O BSI 07-2000 STD*BSI BS EN LOb3-ENGL 2000 W Lb24669 08b04LL L3L M Class SG1 SG2 Page 6 EN 1063:1999 Table 2: Classification and test requirements for testing the
36、bullet resistance of glazing: shot guns Type Calibre of weapon shotgun cal. 12/70 shotgun cal. 12/70 Type solid lead slug) slug solid lead Mass Test conditions g 31,O f0,5 31,O f0,5 test striking nr.of striking range velocity strikes distance m m/S mm 10,OO 420 1 f0,5 *20 10,OO 420 3 125 f0,5 *20 f1
37、0 NOTE 1: The classes BR1 BR7 are classified in order of the level of protection offered, e.g. a panel complying with the requirements specified for a certain class complies with those specified for the preceding classes. NOTE 2: Classes SG do not necessarily comply with the requirements specified i
38、n the classes BR, as the ammunition is different. 5 Test pieces for type testing The composition and materials of the test pieces shall comply with the specification of the manufacturer. The sample submitted for testing shall be representative of the normal production quality. The attack face shall
39、be marked by the supplier. Every test piece shall be clearly marked to identie the product. The sample submitted for type testing shall consist of 3 test pieces for each class for which testing is required. At least one extra test piece shall be taken as a reserve. The size of the test pieces shall
40、be (500 f 5) mm x (500 f 5) mm square. The edges of the test pieces shall be smooth for ease of handling. 6 Performance requirements Each of the three pieces of a sample shall comply with at least one of the following requirements, when subjected to the test in 7.2. 6.1 No perforation of the glazing
41、 by the bullet or parts of the bullet and no perforation of the witness foil by glass splinters from the rear face. This type of bullet-resistant glazing shall be classified in the appropriate class with the additional mark: “NS” (no splinters). 6.2 No perforation of the glazing by the bullet or par
42、ts of the bullet, but with perforation of the witness foil by glass splinters from the protected face. This type of bullet-resistant glazing shall be classified in the appropriate class with the additional mark: 66 , LL S ( splinters”). Q BSI 07-2000 Page 7 EN 1063:1999 7 Test method 7.1 Apparatus T
43、he testing device shall consist of: 7.1.1 Rigid frame The frame shall not move under the impact of the projectiles. The conditioned test piece shall be mounted in a rigid frame, in a vertical position and at the distance from the muzzle of the fire arm specified in table 1. The mounting of the test
44、piece in the frame shall meet the following requirements: - the test piece shall be mounted perpendicular to the firing line; - between the glass edges and the frame, neoprene rubber strips shall be applied, of hardness 40 IHRD to 60 IHRD according to IS0 48, thickness 4 mm, and width (30 i 5) mm; -
45、 at the bottom of the rebate, neoprene rubber strips shall be applied, of hardness 40 IHRD to 60 IHR according to IS0 48, thickness 4 mm, and width equal to the full thickness of the test piece; - all four glass edges shall be uniformly clamped over an area of (30 f 5) mm width, leaving a clear targ
46、et area of about 440 mm x 440 mm; - the clamping pressure shall be such that the glass edges remain in place during the test but such that no stresses are induced that might affect the result. NOTE: Clamping pressure is not always precisely defined, as the effect of clamping on the final result is r
47、elatively small. 7.1.2 Splinter collecting box The glass splinters released from the rear face of the test piece and bullet fragments passing through the test piece are gathered by a splinter collecting box that is positioned behind the test piece and is fixed to the rigid frame. The splinter collec
48、ting box shall have an opening at the front of at least 440 mm x 440 mm that matches the target area in the frame, and shall fully enclose the space between the test piece and the witness foil. A requirement for the splinter collecting box is that the witness foil shall be positioned according to 7.
49、1.3 and be easily accessible for examination and replacement. 7.1.3 Witness foil The wounding potential of the glass splinters released from the rear face shall be determined with a witness foil. The witness foil consists of an aluminium foil, thickness 0,02 mm and density 54 g/m2. The aluminium foil shall be mounted in the splinter collecting box in a vertical position at a distance of (500 f 1 O) mm behind the test piece and shall have a clear surface of at least 440 mm x 440 mm that matches the target area. The aluminium foil shall be mou
