1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 12561-1:2011Railway applications TankwagonsPart 1: Identification plates for tank wagonsfor the carriage of dangerous goodsBS EN 12561-1:2011 BRITISH STANDARDNational forew
2、ordThis British Standard is the UK implementation of EN 12561-1:2011.It supersedes BS EN 12561-1:1999 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee RAE/1/-/9, Railway Applications - Wagons (Tank/Freight).A list of organizations represented on this com
3、mittee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 72807 5ICS 13.300; 45.060.20Compliance with a British Standard cannot confer immunity fro
4、mlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2011.Amendments issued since publicationDate Text affectedBS EN 12561-1:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12561-1 June 2011 ICS 13.300; 45.060.20
5、 Supersedes EN 12561-1:1998English Version Railway applications - Tank wagons - Part 1: Identification plates for tank wagons for the carriage of dangerous goods Applications ferroviaires - Wagons citernes - Partie 1 : Plaques didentit des wagons citernes destins au transport des matires dangereuses
6、 Bahnanwendungen - Kesselwagen - Teil 1: Kennzeichnungsschilder von Kesselwagen fr die Befrderung von gefhrlichen Gtern This European Standard was approved by CEN on 3 June 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
7、European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official ver
8、sions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria
9、, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEA
10、N COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12561-1:2011: EBS EN 12561-1:20
11、11EN 12561-1:2011 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Identification plates for gases 54.1 General 54.2 Identification plate for gases liquefied under pressure .54.3 Identification plate for refrigerated liquefied gases .85 Identification plates
12、 for liquid and solid substances 105.1 General . 105.2 Identification plate for general purposes . 105.3 Identification plate for specific substances . 116 Common requirements 146.1 Manufacturing process and materials 146.2 Marking 146.3 Position and attachment of the identification plate 146.4 Lang
13、uage . 14Bibliography . 15Figures Figure 1 Identification plate for liquefied gases .6Figure 2 Identification plate for refrigerated liquefied gases 8Figure 3 Identification plate for general purposes 10Figure 4 Identification plate for specific substances 12Figure 5 Location of identification plate
14、 . 14Tables Table 1 Particulars to be indicated on the identification plate for liquefied gases .7Table 2 Particulars to be indicated on the identification plate for refrigerated liquefied gases 9Table 3 Particulars to be indicated on the identification plate for general purposes 11Table 4 Particula
15、rs to be indicated on the identification plate for specific substances 13BS EN 12561-1:2011EN 12561-1:2011 (E) 3 Foreword This document (EN 12561-1:2011) has been prepared by Technical Committee CEN/TC 256 “Railway applications”, the secretariat of which is held by DIN. This European Standard shall
16、be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2011, and conflicting national standards shall be withdrawn at the latest by December 2011. Attention is drawn to the possibility that some of the elements of this docu
17、ment may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12561-1:1998. This European Standard Railway applications Tank wagons consists of the following parts: Part 1: Identification plates f
18、or tank wagons for the carriage of dangerous goods; Part 2: Bottom emptying devices for liquid products including vapour return; Part 3: Bottom filling and emptying devices for gases liquefied under pressure; Part 4: Devices for top filling and emptying of liquid products; Part 5: Devices for vapour
19、 return while filling or emptying of liquid products; Part 6: Manholes; Part 7: Platforms and ladders; Part 8: Heating connections. The previous version of EN12561-1 set requirements for marking and identification plate for tank wagons. All the marking requirements for tank wagons are put in the prE
20、N 15877-1. The EN12561-1 describes only the identification plate. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Es
21、tonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 12561-1:2011EN 12561-1:2011 (E) 4 1 Scope This European Standa
22、rd lays down the identification plates for tank wagons used for the carriage of: liquefied gases of class 2 of RID, substances of classes 3, 4.1, 4.2, 4.3, 5.1, 5.2, 6.1, 6.2, 8 and 9 of RID. Compressed gases have not been considered in this European Standard. This European Standard also defines the
23、 dimensions and the fixing of identification plates and various particulars to be marked on them. The requirements of RID shall override conflicting requirements of this European Standard. This European Standard applies to new tank wagons built after the 1stJanuary 2010. 2 Normative references The f
24、ollowing referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10088-2, Stainless steels Part 2: Technical deliver
25、y conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 14564, Tanks for transport of dangerous goods- Terminology 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 14564 and the following apply. 3.1 capacity capacit
26、y of shell or shell compartment for tanks, i.e. the total inner volume of the shell or shell compartment expressed in litres or cubic metres. NOTE When it is impossible to completely fill the shell or the shell compartment because of its shape or construction, this reduced capacity shall be used for
27、 the determination of the degree of filling and for the marking of the tank 3.2 expert person who carries out tests on tanks and who is approved by a competent authority 3.3 gauge pressure pressure in excess of atmospheric pressure NOTE pressures are always indicated as gauge pressure in this docume
28、nt.“ BS EN 12561-1:2011EN 12561-1:2011 (E) 5 4 Identification plates for gases 4.1 General The identification plates shall be in accordance with and with EN 12561-1. NOTE See also the requirements of the current version of RID 2. mark of Figures 1 and 2 is given according the TPED directive 1. 4.2 I
29、dentification plate for gases liquefied under pressure The identification plate for the carriage of gases liquefied under pressure shall be in accordance with Figure 1. The particulars to be indicated on this plate in the numbered fields are contained in Table 1. BS EN 12561-1:2011EN 12561-1:2011 (E
30、) 6 Dimensions in millimetres Figure 1 Identification plate for liquefied gases BS EN 12561-1:2011EN 12561-1:2011 (E) 7 Table 1 Particulars to be indicated on the identification plate for liquefied gases No. Particulars to be indicated 1 Manufacturers name or mark 2 Approval number given by the comp
31、etent authority or a body designated by this authority. After the /, the 4 last digits shall be the numerical code of the notify body. 3 Manufacturers serial number 4 Year of manufacture 5 Test pressure in MPa 6 External design pressure in MPa 7 Capacity of the tank in litres (in the case of multipl
32、e-element shells, the capacity of each element) 8 Design temperature in C (only required if above +50 C or below -20 C) 9 Material of the shell (and of the ends if different) according to EN where available and where appropriate the protective lining 10 On shells equipped with thermal insulation, th
33、e expression ”thermally insulated” or “themally insulated by vacuum“, otherwise insert the expression ”NONE” 11 The names in full of the gases for the carriage of which the shell is approved and corresponding mass in kg. This mass is calculated by multiplying the capacity of the tank by the maximum
34、permissible mass of contents per litre of capacity. 12 Fields for marking of: date (month and year) of the initial test and of most recent test like: MM/YYP for periodic or initial test MM/YYL for intermediate test stamp of expert who carried out the test BS EN 12561-1:2011EN 12561-1:2011 (E) 8 4.3
35、Identification plate for refrigerated liquefied gases The identification plate for the carriage of refrigerated liquefied gases shall be in accordance with Figure 2. The particulars to be indicated on this plate in the numbered fields are contained in Table 2. Dimensions in millimetres Figure 2 Iden
36、tification plate for refrigerated liquefied gases BS EN 12561-1:2011EN 12561-1:2011 (E) 9 Table 2 Particulars to be indicated on the identification plate for refrigerated liquefied gases No. Particulars to be indicated 1 Manufacturers name or mark 2 Approval number given by the competent authority o
37、r a body designated by this authority. After the /, the 4 last digits shall be the numerical code of the notify body. 3 Manufacturers serial number 4 Year of manufacture 5 Test pressure in MPa 6 External design pressure in MPa 7 Capacity of the tank in litres (in the case of multiple-element shells,
38、 the capacity of each element) 8 Design temperature in C. This corresponds to the lowest permissible filling temperature 9 Material of the shell (and of the ends if different) according to EN where available and where appropriate, the protective lining 10 According to the type of insulation, the exp
39、ression ”thermally insulated” or ”thermally insulated by vacuum” 11 Maximum permissible working pressure in MPa 12 The names in full of the gases for the carriage of which the shell is approved and corresponding mass. This mass is calculated by taking into account the lowest filling temperature, the
40、 relevant density and the allowable filling factor 13 Fields for marking of: date (month and year) of the initial test and of most recent test like: MM/YYP for periodic or initial test MM/YYL for intermediate test stamp of expert who carried out the test BS EN 12561-1:2011EN 12561-1:2011 (E) 10 5 Id
41、entification plates for liquid and solid substances 5.1 General The identification plates shall be in accordance with the requirements of the current version of RID 2 and with EN 12561-1. 5.2 Identification plate for general purposes The identification plate for tank wagons for the carriage of subst
42、ances the name, approved concentration and/or maximum permissible load mass of which is not required to be specified shall be in accordance with Figure 3. The particulars to be indicated on this plate in the numbered fields are contained in Table 3. Dimensions in millimetres Figure 3 Identification
43、plate for general purposes BS EN 12561-1:2011EN 12561-1:2011 (E) 11 Table 3 Particulars to be indicated on the identification plate for general purposes No. Particulars to be indicated 1 Manufacturers name or mark 2 Approval number given by the competent authority or a body designated by this author
44、ity 3 Manufacturers serial number 4 Year of manufacture 5 Test pressure in MPa 6 External design pressure in MPa 7 Capacity of the tank in litres (in the case of multiple-element shells, the capacity of each element) 8 Design temperature in C (only required if above +50 C or below -20 C) 9 Material
45、of the shell (and of the ends if different) according to EN where available 10 Material of lining or coating where this is applied to protect the tank if applicable. Brand names may be used if they are in common use 11 Maximum permissible working pressure in MPa 12 RID calculation pressure in MPa 13
46、 Fields for marking of: date (month and year) of the initial test and of most recent test like: MM/YYP for periodic or initial test MM/YYL for intermediate test stamp of expert who carried out the test 5.3 Identification plate for specific substances The identification plate for tank wagons for the
47、carriage of substances the name, approved concentration and/or maximum permitted load mass of which are required to be specified shall be in accordance with Figure 4. The particulars to be indicated on this plate in the numbered fields are contained in Table 4. BS EN 12561-1:2011EN 12561-1:2011 (E)
48、12 Dimensions in millimetres Figure 4 Identification plate for specific substances BS EN 12561-1:2011EN 12561-1:2011 (E) 13 Table 4 Particulars to be indicated on the identification plate for specific substances No. Particulars to be indicated 1 Manufacturers name or mark 2 Approval number given by
49、the competent authority or a body designated by this authority 3 Manufacturers serial number 4 Year of manufacture 5 Test pressure in MPa 6 External design pressure in MPa 7 Capacity of the tank in litres (in the case of multiple-element shells, the capacity of each element) 8 Design temperature in C (only required if it is above +50 C or below -20 C) 9 Material of the shell (and of the ends if different) according to EN whe
