1、BRITISH STANDARDBS EN 12629-2:2002Machines for the manufacture of constructional products from concrete and calcium-silicate Safety Part 2: Block making machinesICS 91.220g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g
2、40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58+A1:2010National forewordThis British Standard is the UK implementation of EN 12629-2:2002+A1:2010. It supersedes BS EN 12629-2:2002 which is withdrawn.The start and finish of text introduced or altered by amendment is indicated
3、in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by !“.The UK participation in its preparation was entrusted to Technical Committee MCE/3/7, Machines for precast concrete and calcium silicate pr
4、oducts Safety.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer
5、immunity from legal obligations.BS EN 12629-2:2002+A1:2010This British Standard, was published under the authority of the Standards Policy and Strategy Committee on 16 July 2003 BSI 2010Amendments/corrigenda issued since publicationDate Comments 31 October 2010 Implementation of CEN amendment A1:201
6、0ISBN 978 0 580 63122 1EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12629-2:2002+A1 September 2010 ICS 91.220 Supersedes EN 12629-2:2002English Version Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 2: Block making machines Machines
7、 pour la fabrication de produits de construction en bton et silico-calcaire - Scurit - Partie 2: Machines blocs Maschinen fr die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 2: Steinformmaschinen This European Standard was approved by CEN on 1 November 2002 and
8、includes Amendment 1 approved by CEN on 5 August 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
9、concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into i
10、ts own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
11、Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Br
12、ussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12629-2:2002+A1:2010: EEN 12629-2:2002+A1:2010 (E) 2 Contents page Foreword 3Introduction . 41 Scope 42 Normative references 53 Terms and definitions . 54 List of signific
13、ant hazards 64.1 Mechanical hazards (see informative annex B) 64.2 Electrical hazards 84.3 Hazards generated by vibration . 85 !Safety requirements and/or protective measures“ . 86 !Verification of safety requirements and/or protective measures“ 97 Information for use 98 Marking . 10Annex A (informa
14、tive) Mechanical hazards zones for a common block making machine and requirements and measures . 11Annex B (informative) Terminology of a common block making machine . 12Annex ZA (informative) ! Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC“ .
15、13Bibliography 14BS EN 12629-2:2002+A1:2010EN 12629-2:2002+A1:2010 (E) 3 Foreword This document (EN 12629-2:2002+A1:2010) has been prepared by Technical Committee CEN /TC 151 “Construction equipment and building material machines - Safety“, the secretariat of which is held by DIN. This European Stan
16、dard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2011, and conflicting national standards shall be withdrawn at the latest by March 2011. Attention is drawn to the possibility that some of the elements of this
17、 document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document includes Amendment 1, approved by CEN on 2010-08-05. This document supersedes EN 12629-2:2002. The start and finish of text introduced or alter
18、ed by amendment is indicated in the text by tags ! “. !This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informat
19、ive Annex ZA, which is an integral part of this document.“ !The series “Machines for the manufacture of constructional products from concrete and calcium silicate Safety“ consists of the following parts: Part 1: Common requirements Part 2: Block making machines Part 3: Slide and turntable machines P
20、art 4: Concrete roof tile making machines Part 5.1: Pipe making machines manufacturing in the vertical axis Part 5.2: Pipe making machines manufacturing in the horizontal axis Part 5.3: Pipe prestressing machines Part 5.4: Concrete pipe coating machines Part 6: Stationary and mobile equipment for th
21、e manufacture of precast reinforced products Part 7: Stationary and mobile equipment for long line manufacture of prestressed products Part 8: Machines and equipment for the manufacture of constructional products from calcium silicate (and concrete)“ !deleted text“ According to the CEN/CENELEC Inter
22、nal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxemb
23、ourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 12629-2:2002+A1:2010EN 12629-2:2002+A1:2010 (E) 4 Introduction !This European Standard is a Type C-standard as stated in EN ISO 12100. The machinery concerned and the
24、 extent to which hazards, hazardous situation and events are covered are indicated in the scope of this document. When provisions of this type C document are different from those, which are stated in type A or B documents, the provisions of this type C document take precedence over the provisions of
25、 the other documents, for machines that have been designed and built according to the provisions of this type C document. This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific for the block making machines as described in 1.1. With the aim
26、 of clarifying the intentions of the document it should be noticed that the following assumptions were made when producing it: specific conditions of use or environmental conditions out of the scope of the document shall be the subject of negotiations between the manufacturer and the user/owner, the
27、 equipment will only be used by competent and designated persons, the place of use/installation is adequately lit, all operations are carried out by specially trained operators.“ 1 Scope 1.1 !This part of EN 12629, taken together with EN 12629-1:2000+A1:2010, applies to machines for the manufacture
28、of blocks, kerbs, paving stones and similar concrete products. EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calciumsilicate. This document specifies the additional requirements to and/or the deviations
29、from EN 12629-1:2000+A1:2010 specific to the machines it covers.“ 1.2 !This European Standard deals with all significant hazards pertinent to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This Europe
30、an Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards.“ 1.3 This European Standard applies to the machines from the point at which the mixture enters the machine (see point 1-2 of annex B) and the point where the pallet boards are
31、brought to the assembly (see point 3 of annex B) until the point where the green products are removed from the machine assembly to the curing system (see point 4 of annex B). !deleted text“ BS EN 12629-2:2002+A1:2010EN 12629-2:2002+A1:2010 (E) 5 !1.4“ This European Standard deals with the hazards !d
32、eleted text“ listed in clause 4 which can arise during the operation and maintenance, including the interfaces, of the block making machines, when carried out in accordance with the specifications given by the manufacturer or his authorised representative. NOTE 1 Amendment is under preparation to de
33、al with noise, in particular for measures to reduce noise at source and a noise test code including noise declaration. NOTE 2 Interfaces between the block making machines and others of the installation are dealt with in !EN 12629-1:2000+A1:2010 (7.2)“. This standard establishes safety requirements a
34、nd/or methods of protection which apply to these machines. ! 1.5 This document is not applicable to block making machines, which are manufactured before the date of publication of this document by CEN.“ 2 Normative references !The following referenced documents are indispensable for the application
35、of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.“ !deleted text“ !EN 12629-1:2000+A1:2010“, Machines for the manufacture of constructional products from concrete and calci
36、um-silicate Safety Part 1: Common requirements !EN ISO 12100-1:2003, Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-1:2003, Safety of machinery Basic concepts, general principles for design Part 2: Technical pr
37、inciples (ISO 12100-2:2003)“ 3 Terms and definitions !For the purposes of this document, the terms and definitions given in EN ISO 12100-1:2003, EN 12629-1:2000+A1:2010 and the following apply.“ NOTE See also annex B for terminology of a typical block making machine. 3.1 drawing box container having
38、 the shape of a box with an open or movable bottom. The drawing box fills the mould with the mixture 3.2 drawing box grid machine element which is placed at the bottom of the drawing box. It consists of bars specially designed so as to assist a uniform supply of fresh concrete into the mould. The gr
39、id can be loose, fixed or movable with respect to the drawing box 3.3 feed hopper device that contains the mixture which is transported to the drawing box by a discharge gate or a dosing belt BS EN 12629-2:2002+A1:2010EN 12629-2:2002+A1:2010 (E) 6 3.4 draw plate integral system which is part of the
40、assembly of the machine It is placed between the mould and the pallet board. It is designed to: provide the surface condition of the underside of the products; produce profiles to the underside of the product 3.5 vibration table equipment located beneath the mould and mounted on flexible suspension
41、and features vibrators. Vibration is transmitted to the mould via the pallet board 3.6 internal pallet board transfer mechanism device that feeds empty pallet boards beneath the mould and discharges the fresh products 3.7 tamper cleaning device device that automatically moves transversally to clean
42、the moulding part of the tamper between two lots 3.8 face mix filling device part of a machine consisting of a frame, a hopper and a drawing box which can be connected to or removed from the main machine frame 3.9 pallet board wooden, metal or other material support placed during manufacturing betwe
43、en the vibrating table and the mould to form the base thus permitting, after mould release, transport of green products to the curing chambers 3.10 tamper removable tooling element that forms the upper part of the mould. It is intended to: assist the compacting of concrete by compression; form the u
44、pper part of the products. 4 List of significant hazards This clause contains all hazards, as far as they are dealt with in this European Standard, identified by risk assessments significant for this type of machinery and which require action to eliminate or reduce risk. !deleted text“ 4.1 Mechanica
45、l hazards (see informative annex B) Annex B (informative) illustrates an example of a common machine type. In accordance with !Clause 4 of EN 12629-1:2000+A1:2010“ the hazard zones, marked 1-8 at annex A of this standard, are described in the following table (see also 4.1.1 to 4.1.6 for detailed mec
46、hanical hazards). BS EN 12629-2:2002+A1:2010EN 12629-2:2002+A1:2010 (E) 7 Table 1 Mechanical hazards and hazard zones Hazard zones Hazards See subclauses 1 Crushing Shearing Cutting or severing 4.1.1 4.1.2 4.1.3 2 Shearing Cutting or severing 4.1.2 4.1.3 3 Shearing Cutting or severing 4.1.2 4.1.3 4
47、Crushing 4.1.15 Entanglement 4.1.46 Crushing Cutting or severing 4.1.1 4.1.3 7 Shearing Cutting or severing Entanglement 4.1.2 4.1.3 4.1.4 8 Cutting or severing 4.1.3Equipment High pressure 4.1.5 Floor Slip, trip or fall 4.1.6 Around the machine Vibration 4.3 4.1.1 Crushing hazards Between the drawi
48、ng box(es) and the dosing device and fixed parts of the machine assembly (see hazard zone 6, annex A). Between one of the fixed parts of the machine and the sheet pulling device (see hazard zone 4, annex A). In the event of gravity drop of the support cross member, of the mould or of the attaching p
49、arts of the mould during action of personnel with the machine which is at a stop (see hazard zone 1, annex A). 4.1.2 Shearing hazards Between the mould and the fixed parts of the machine assembly (see hazard zone 1, annex A). Between the inner mould and the outside mould (see hazard zone 1, annex A). Between the tamper support crossbeam and the hopper or the fixed parts of the machine (see hazard zone 2, annex A). Between the tamper and the tamper support crossbeam and the mould (s
