1、BSI Standards PublicationBS EN 13277-3:2013Protective equipment formartial artsPart 3: Additional requirements and testmethods for trunk protectorsBS EN 13277-3:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 13277-3:2013. It supersedes BS EN 13277-3:2000+A
2、1:2007 which is withdrawn.The UK committee voted against the approval of this standard. Thereason for this is that the UK experts expressed the opinion that the descriptions of test equipment and test tolerances lacked necessarydetail. This could result in larger correlation variance in the test bet
3、ween facilities.The UK participation in its preparation was entrusted to Technical Committee PH/3/11, Protective Equipment For Sports Players.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessa
4、ry provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014ISBN 978 0 580 81776 2ICS 13.340.10; 97.220.30 Compliance with a British Standard cannot confer immunity from legal obligations.This British
5、Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2014.Amendments issued since publicationDate Text affectedBS EN 13277-3:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13277-3 December 2013 ICS 13.340.10 Supersedes EN 13277-3:2000English
6、Version Protective equipment for martial arts - Part 3: Additional requirements and test methods for trunk protectors quipement de protection pour les arts martiaux - Partie 3 : Exigences et mthodes dessai complmentaires relatives aux protge-torses Schutzausrstung fr den Kampfsport - Teil 3: Zustzli
7、che Anforderungen und Prfverfahren fr den OberkrperschutzThis European Standard was approved by CEN on 26 October 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without
8、 any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other lan
9、guage made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denma
10、rk, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE
11、FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13277-3:2013 EBS EN 13277-3:201
12、3EN 13277-3:2013 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Requirements .4 4.1 Sizing 4 4.2 Combinations .4 4.3 Restraint .4 4.4 Zone of protection .4 4.5 Impact performance 5 4.6 Mass and thickness for trunk protectors for karate .5 5 Testing 6 5
13、.1 Sampling .6 5.2 Conditioning .6 5.3 Restraint .6 5.4 Zone of protection .6 5.5 Impact performance 6 5.5.1 Apparatus .6 5.5.2 Procedure .7 6 Marking .8 7 Information supplied by the manufacturer .8 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of
14、 EU Directive 89/686/EEC 9 BS EN 13277-3:2013EN 13277-3:2013 (E) 3 Foreword This document (EN 13277-3:2013) has been prepared by Technical Committee CEN/TC 162 “Protective clothing including hand and arm protection and lifejackets”, the secretariat of which is held by DIN. This European Standard sha
15、ll be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2014, and conflicting national standards shall be withdrawn at the latest by June 2014. Attention is drawn to the possibility that some of the elements of this document
16、may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13277-3:2000. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Associati
17、on, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. This standard is composed of the following parts: EN 13277-1, Protective equipment for martial arts Part 1: General requirements an
18、d test methods EN 13277-2, Protective equipment for martial arts Part 2: Additional requirements and test methods for instep protectors, shin protectors and forearm protectors EN 13277-3, Protective equipment for martial arts Part 3: Additional requirements and test methods for trunk protectors (the
19、 present document) EN 13277-4, Protective equipment for martial arts Part 4: Additional requirements and test methods for head protectors EN 13277-5, Protective equipment for martial arts Part 5: Additional requirements and test methods for genital protectors and abdominal protectors EN 13277-6, Pro
20、tective equipment for martial arts Part 6: Additional requirements and test methods for breast protectors for females EN 13277-7, Protective equipment for martial arts Part 7: Additional requirements and test methods for hand and foot protectors According to the CEN-CENELEC Internal Regulations, the
21、 national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia
22、, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 13277-3:2013EN 13277-3:2013 (E) 4 1 Scope This European Standard specifies additional requirements and test methods for trunk protector
23、s used in unarmed martial arts such as taekwondo, karate, kick-boxing and similar disciplines. It also applies to breast protectors for men. For general requirements and test methods for protective equipment for martial arts, see EN 13277-1. 2 Normative references The following documents, in whole o
24、r in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13277-1:2000, Protective equipment for
25、martial arts - Part 1: General requirements and test methods 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13277-1:2000 apply. 4 Requirements 4.1 Sizing The manufacturer shall indicate in centimetres the range of the wearers height for which this pr
26、otector is designed. 4.2 Combinations Trunk protectors can be used in combination with other protectors for martial arts. In the case of combined use, the requirements specified for the individual protectors are also to apply. Possible combinations shall be indicated in the information supplied by t
27、he manufacturer. If combined use is not permitted by the manufacturer, this restriction shall be indicated in the information supplied by the manufacturer. 4.3 Restraint A restraint system shall be supplied by the manufacturer which enables the user to attach trunk protectors with the support of no
28、more than one assistant. For karate, the fixing systems shall be only textiles. They shall never consist of metal, plastic or similar hard materials. 4.4 Zone of protection Location and dimensions of the zone of protection, see Figure 1 and Table 1. BS EN 13277-3:2013EN 13277-3:2013 (E) 5 Figure 1 L
29、ocation of the zone of protection of trunk protectors Table 1 Zone of protection of trunk protectors Dimensions in millimetres Wearers height l1l2l3l4l5min. min. min. min. min. 1 520 to 1 700 710 160 210 175 110 1 700 to 1 880 760 180 230 190 130 1 880 810 200 250 210 150 4.5 Impact performance Trun
30、k protectors comply with this standard if the worst result after testing in accordance with 5.5 meets the following requirements: impact energy: 12 J; impact energy for karate: 2,6 J; peak force: max. 3 kN; positions to be tested: min. 3. 4.6 Mass and thickness for trunk protectors for karate For an
31、y size of trunk protectors for karate the total mass shall not exceed 250 g. For any size of trunk protectors for karate the thickness shall not exceed 15 mm. BS EN 13277-3:2013EN 13277-3:2013 (E) 6 5 Testing 5.1 Sampling Sampling shall be carried out according to EN 13277-1:2000, 5.1. 5.2 Condition
32、ing Conditioning shall be carried out according to EN 13277-1:2000, 5.2. 5.3 Restraint Restraint testing shall be carried out according to EN 13277-1:2000, 5.4. When testing the restraint, the protector shall be attached to the trunk of a test person of an appropriate height in accordance with the i
33、nformation supplied by the manufacturer. A test force of 50 N shall be applied at the edge of the zone of protection, in the directions and in the order shown on Figure 2, tangential to the surface of the body of the test person. Key 1 to 6 directions and order of the tests Figure 2 Restraint test o
34、f trunk protectors 5.4 Zone of protection When testing according to EN 13277-1:2000, 5.5, the protector shall be attached to a test person of an appropriate height in accordance with the information supplied by the manufacturer. The gauge shall be placed onto the surface of the zone of protection. W
35、hen the position of best coverage of the gauge is found, the outline of the gauge shall be marked on the protector. 5.5 Impact performance5.5.1 Apparatus The principle of impact testing is shown in Figure 3. BS EN 13277-3:2013EN 13277-3:2013 (E) 7 A flat horizontal steel plate with a width of at lea
36、st 300 mm, a length of at least 350 mm and a thickness of at least 20 mm shall be used as a support of the sample. In the centre of the flat plate there shall be a cylindrical hole with a diameter of (106 2) mm. A cylindrical anvil with a diameter of (100 2) mm, a thickness of at least 20 mm with a
37、flat upper surface shall be mounted on a load cell. The surface of the anvil facing the striker shall be in level with the surface of the flat plate with a tolerance of 1 mm. A compression ring made of steel with a mass of (10 0,1) kg, (140 0,1) mm internal and (260 4) mm external diameter shall be
38、used to fix the sample to the support. The striker shall be able to fall free in the vertical axis of the anvil with a tolerance of 2 mm. The striker shall be guided in such a way, that it will always reach at least 95 % of the freefall velocity. A means of measuring the velocity of the striker at t
39、he point of impact shall be provided. To measure the maximum peak force an electronic measurement device with the following characteristics shall be used: Measurement frequency: min. 2 000 Hz; Accuracy class of the load cell: 0,2; Maximum load: 10 kN. 5.5.2 Procedure The trunk protector shall be pla
40、ced on the flat support so that the test positions to be tested shall be above the centre of the anvil and shall be fixed with the compression ring. The compression ring shall be placed so that the anvil is situated in the centre of the ring with a tolerance of 5 mm. The trunk protector shall be mov
41、ed on the support in order to reach every test position to be tested. If it is not possible to press the trunk protector flat with the compression ring, the protector shall be cut, until it is possible to place it flat. The test positions shall be selected so that they are not closer than 20 mm to t
42、he limit of the zone of protection. If the test position is closer to the edge of the zone of protection than 70 mm, and there is a gap between the protector and the compression ring, a part of the same protector or of another protector of the same construction shall be cut and placed in the gap. Th
43、e test positions shall be selected to include the positions on the protector where the worst test results are assumed to be likely. Three impacts of the same energy level shall be carried out on each test position with an interval of (60 10) s. No other test position previously tested shall be withi
44、n a circle of 80 mm around the test position to be tested. If positions are selected to be impacted less than 80 mm distant from each other, at least two protectors of the same type shall be selected for impact testing. BS EN 13277-3:2013EN 13277-3:2013 (E) 8 Dimensions in millimetres Key 1 striker
45、4 steel plate 2 compression ring 5 anvil 3 trunk protector 6 load cellFigure 3 Principle of impact testing of trunk protectors 6 Marking Marking shall be carried out in accordance with EN 13277-1:2000, Clause 6. Additionally the karate trunk protectors shall be marked with an indication that they sh
46、all only be used for karate. 7 Information supplied by the manufacturer Requirements for the Information to be supplied by the manufacturer shall be in accordance with EN 13277-1:2000, Clause 7. BS EN 13277-3:2013EN 13277-3:2013 (E) 9 Annex ZA (informative) Relationship between this European Standar
47、d and the Essential Requirements of EU Directive 89/686/EEC This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to Essential Requirements of the New Approach Directive 89/686/EEC. On
48、ce this standard is cited in the Official Journal of the European Union under that Directive and has been implemented as a national standard in at least one Member State, compliance with the clauses of this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a pres
49、umption of conformity with the corresponding Essential Requirements of that Directive and associated EFTA regulations. Table ZA.1 Correspondence between this European Standard and Directive 89/686/EEC Clause(s)/subclause(s) of this EN Essential Requirements (ERs) of Directive 89/686/EEC Qualifying remarks/Notes 4.5 1.1.2.2 Classes of protection appropriate to different levels of risk 4.4 1.2.1 Absence of risks and other nuisance factors4.6 1.3.2 Lightness and strength Clause 6, 7 1.4 Information supp
