EN 14037-1-2003 Ceiling mounted radiant panels supplied with water at temperature below 120 C - Part 1 Technical specifications and requirements《装有用低于120度温水供暖辐射板的天花板 第1部分 技术规范和要求》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

ASTM A923-2008 Standard Test Methods for Detecting Detrimental Intermetallic Phase in Duplex Austenitic Ferritic Stainless Steels《测定双联奥氏体 铁素体不锈钢不稳定金属间相的标准试验方法》.pdf

ASTM A923-2014 Standard Test Methods for Detecting Detrimental Intermetallic Phase in Duplex Austenitic Ferritic Stainless Steels《测定双联奥氏体 铁素体不锈钢不稳定金属间相的标准试验方法》.pdf

ASTM A924 A924M-2007 Standard Specification for General Requirements for Steel Sheet Metallic-Coated by the Hot-Dip Process《热浸镀锌金属涂层薄钢板一般要求的标准规格》.pdf

ASTM A924 A924M-2008 Standard Specification for General Requirements for Steel Sheet Metallic-Coated by the Hot-Dip Process.pdf

ASTM A924 A924M-2008a Standard Specification for General Requirements for Steel Sheet Metallic-Coated by the Hot-Dip Process.pdf

ASTM A924 A924M-2009 Standard Specification for General Requirements for Steel Sheet Metallic-Coated by the Hot-Dip Process.pdf

ASTM A924 A924M-2009a Standard Specification for General Requirements for Steel Sheet Metallic-Coated by the Hot-Dip Process《热浸处理金属涂覆薄钢板的一般要求用标准规范》.pdf

ASTM A924 A924M-2010 Standard Specification for General Requirements for Steel Sheet Metallic-Coated by the Hot-Dip Process《热浸镀锌金属涂层薄钢板的一般要求标准规范》.pdf

ASTM A924 A924M-2010a Standard Specification for General Requirements for Steel Sheet Metallic-Coated by the Hot-Dip Process《热浸镀锌金属涂层薄钢板一般要求的标准规格》.pdf