1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 1870-4:2012Safety of woodworking machines Circular sawing machinesPart 4: Multiblade rip sawing machines with manual loading and/or unloadingBS EN 1870-4:2012 BRITISH STAND
2、ARDNational forewordThis British Standard is the UK implementation of EN 1870-4:2012. It supersedes BS EN 1870-4:2001+A1:2009, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e M T E / 2 3 , W o o d w o r k i n g m a c h i n e s .A list o
3、f organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limit
4、ed 2012ISBN 978 0 580 68422 7 ICS 79.120.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2012.Amendments issued since publicationDate T e x t a f f e
5、 c t e dBS EN 1870-4:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1870-4 March 2012 ICS 79.120.10 Supersedes EN 1870-4:2001+A1:2009English Version Safety of woodworking machines - Circular sawing machines - Part 4: Multiblade rip sawing machines with manual loading and/or unloading Scuri
6、t des machines pour le travail du bois - Machines scies circulaires - Partie 4: Scies circulaires dligner multilames chargement et/ou dchargement manuel Sicherheit von Holzbearbeitungsmaschinen - Kreissgemaschinen - Teil 4: Mehrblattkreissgemaschinen fr Lngsschnitt mit Handbeschickung und/oder Hande
7、ntnahme This European Standard was approved by CEN on 21 January 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliograph
8、ical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibilit
9、y of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hu
10、ngary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Manage
11、ment Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1870-4:2012: EBS EN 1870-4:2012EN 1870-4:2012 (E) 2 Contents Page Foreword 4Introduction .61 Scope 72 Normative references 73 Terms
12、 and definitions .93.1 General 93.2 Definitions . 104 List of significant hazards . 135 Safety requirements and/or measures . 165.1 General . 165.2 Controls . 165.2.1 Safety and reliability of control systems 165.2.2 Position of controls 185.2.3 Starting 195.2.4 Normal stopping . 205.2.5 Emergency s
13、top 205.2.6 Mode selection 215.2.7 Powered adjustments . 235.2.8 Integrated feed 235.2.9 Feed speed control . 245.2.10 Failure of the power supply . 245.2.11 Failure of the control circuits 245.3 Protection against mechanical hazards . 245.3.1 Stability 245.3.2 Risk of break up during operation 255.
14、3.3 Tool holder and tool design . 255.3.4 Braking . 265.3.5 Devices to prevent the possibility or the effect of ejection 275.3.6 Workpiece supports and guides . 455.3.7 Prevention of access to moving parts 455.4 Protection against non-mechanical hazards . 475.4.1 Fire . 475.4.2 Noise 475.4.3 Emissio
15、n of chips and dust . 485.4.4 Electricity . 495.4.5 Ergonomics and handling 495.4.6 Pneumatics 505.4.7 Hydraulics 505.4.8 Electromagnetic compatibility . 505.4.9 Laser 505.4.10 Static electricity 515.4.11 Errors of fitting 515.4.12 Supply disconnection (Isolation) 515.4.13 Maintenance 516 Informatio
16、n for use . 526.1 General . 526.2 Marking 526.3 Instruction handbook . 53BS EN 1870-4:2012EN 1870-4:2012 (E) 3 Annex A (normative) Dimensional tolerances of saw spindles . 57Annex B (normative) Braking tests . 58B.1 Conditions for all tests 58B.2 Tests . 58B.2.1 Un-braked run-down time . 58B.2.2 Bra
17、ked run-down time . 58Annex C (normative) Type test for anti-splinter system . 59C.1 General . 59C.2 Test method . 59C.2.1 Preliminary remarks 59C.2.2 Test equipment 59C.2.3 Test sample, tools, installation 61C.2.4 Test operation 62C.3 Test result. 62C.4 Test report 63Annex D (normative) Impact test
18、 method for guards 64D.1 General . 64D.2 Test method . 64D.2.1 Preliminary remarks 64D.2.2 Testing equipment . 64D.2.3 Projectile for guards 64D.2.4 Sampling. 65D.2.5 Test procedure . 65D.3 Results 65D.4 Assessment . 65D.5 Test report 66D.6 Test equipment for impact test 66Annex ZA (informative) Rel
19、ationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC 67Bibliography 70BS EN 1870-4:2012EN 1870-4:2012 (E) 4 Foreword This document (EN 1870-4:2012) has been prepared by Technical Committee CEN/TC 142 “Woodworking machines - Safety”, the secretariat of wh
20、ich is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2012, and conflicting national standards shall be withdrawn at the latest by September 2012. Attention is drawn to the
21、 possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1870-4:2001+A1:2009. This European Standard has been prepared under a mandate given
22、 to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of the Machinery Directive. For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document. Organisations contributing to the preparation of this
23、European Standard include European Committee of Woodworking Machinery Manufacturers Association “EUMABOIS“. EN 1870 Safety of woodworking machines Circular sawing machines consists of the following parts: Part 1: Circular saw benches (with and without sliding table), dimension saws and building site
24、 saws; Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches; Part 4: Multi-blade rip sawing machines with manual loading and/or unloading; Part 5: Circular saw benches/up-cutting cross-cut sawing machines; Part 6: Circular sawing machines for firewood
25、 and dual purpose circular sawing machines for firewood/circular saw benches, with manual loading and/or unloading; Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading; Part 8: Single blade edging circular rip sawing machines with power driven saw
26、unit and manual loading and/or unloading; Part 9: Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading; Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines; Part 11: Semi-automatic and automatic hori
27、zontal cross-cut sawing machines with one saw unit (radial arm saws); Part 12: Pendulum cross-cut sawing machines; Part 13: Horizontal beam panel sawing machines; Part 14: Vertical panel sawing machines; BS EN 1870-4:2012EN 1870-4:2012 (E) 5 Part 15: Multi-blade cross-cut sawing machines with integr
28、ated feed of the workpiece and manual loading and/or unloading; Part 16: Double mitre sawing machines for V-cutting; Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (manual radial arm saws); Part 18: Dimension saws; Part 19: Circular saw benches (with and without slidi
29、ng table) and building site saws. The European Standards produced by CEN/TC142 are particular to woodworking machines and complement the relevant A and B Standards on the subject of general safety (see introduction of EN ISO 12100:2010 for a description of A, B and C standards). According to the CEN
30、/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lit
31、huania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. BS EN 1870-4:2012EN 1870-4:2012 (E) 6 Introduction This document has been prepared to be a harmonised standard to provide one means of conforming to t
32、he essential safety requirements of the Machinery Directive and associated EFTA regulations. This document is a type “C“ standard as defined in EN ISO 12100:2010. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this d
33、ocument. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of other standards, for machines that have been designed and built according to the provisions of this type
34、C standard. The requirements of this document are directed to manufacturers and their authorised representatives of multi-blade rip sawing machines. They are also useful for designers. This document also includes provisions and examples of information to be provided by the manufacturer to the user.
35、Common requirements for tooling are given in EN 847-1:2005+A1:2007. BS EN 1870-4:2012EN 1870-4:2012 (E) 7 1 Scope This document deals with all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary multi-blade rip sawing machines, hereinafter refe
36、rred to as “machines”, designed to cut solid wood, chipboard, fibreboard, plywood and also these materials, if they are covered with plastic edging and/or plastic/light alloy laminates, when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseea
37、ble misuse; see also 6.3. This document does not apply to machines with vertical roller feed or vertical chain conveyor feed or machines designed to make the first rip cut on a log. This document does not deal with any hazards relating to the combination of single machines with any other machine as
38、part of a line. This document is not applicable to machines which are manufactured before the date of its publication as EN. NOTE Machines covered by this document are listed under 1.3 of the Machinery Directive. 2 Normative references The following documents, in whole or in part, are normatively re
39、ferenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 614-1:2006+A1:2009, Safety of machinery Ergonomic design principles
40、Part 1: Terminology and general principles EN 847-1:2005+A1:2007, Tools for woodworking Safety requirements Part 1: Milling tools, circular saw blades EN 894-1:1997+A1:2008, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 1: General principles for hu
41、man interactions with displays and control actuators EN 894-2:1997+A1:2008, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 2: Displays EN 894-3:2000+A1:2008, Safety of machinery Ergonomics requirements for the design of displays and control actuator
42、s Part 3: Control actuators EN 1005-1:2001+A1:2008, Safety of machinery Human physical performance Part 1: Terms and definitions EN 1005-2:2003+A1:2008, Safety of machinery Human physical performance Part 2: Manual handling of machinery and component parts of machinery EN 1005-3:2002+A1:2008, Safety
43、 of machinery Human physical performance Part 3: Recommended force limits for machinery operation EN 1005-4:2005+A1:2008, Safety of machinery Human physical performance Part 4: Evaluation of working postures and movements in relation to machinery EN 1037:1995+A1:2008, Safety of machinery Prevention
44、of unexpected start-up EN 1049-2:1993, Textiles Woven fabrics Construction Methods of analysis Part 2: Determination of number of threads per unit length (ISO 7211-2:1984 modified) BS EN 1870-4:2012EN 1870-4:2012 (E) 8 EN 1088:1995+A2:2008, Safety of machinery Interlocking devices associated with gu
45、ards Principles for design and selection EN 1760-2:2001+A1:2009, Safety of machinery Pressure sensitive protective devices Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars EN 50178:1997, Electronic equipment for use in power installations
46、EN 50370-1:2005, Electromagnetic compatibility (EMC) Product family standard for machine tools Part 1: Emission EN 50370-2:2003, Electromagnetic compatibility (EMC) Product family standard for machine tools Part 2: Immunity EN 60204-1:2006, Safety of machinery Electrical equipment of machines Part 1
47、: General requirements (IEC 60204-1:2005, modified) EN 60439-1:19991), Low-voltage switchgear and controlgear assemblies Part 1: Type-tested and partially type-tested assemblies (IEC 60439-1:1999) EN 60529:19912), Degrees of protection provided by enclosures (IP Code) (IEC 60529:1989) EN 60825-1:200
48、7, Safety of laser products Part 1: Equipment classification and requirements (IEC 60825-1:2007) EN 61310-1:2008, Safety of machinery Indication, marking and actuation Part 1: Requirements for visual, acoustic and tactile signals (IEC 61310-1:2007) EN 61496-1:2004, Safety of machinery Electro-sensitive protective equipment Part 1: General requirements and tests (IEC 61496-1:2004, modified) EN 61800-5-2:2007, Adjustable speed electrical power drive systems Part 5-2: Safety requirements Functional (IEC 61800-5-2:2007) EN ISO 1421:1998, Rubber- or plastics-coated fabrics Determination of tens
