1、BRITISH STANDARDBS EN 2349-301:2006Aerospace series Requirements and test procedures for relays and contactors Part 301: Pick-up and drop-out voltageThe European Standard EN 2349-301:2006 has the status of a British StandardICS 49.060g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g
2、51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 2349-301:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2007 BSI 2007ISBN 978 0 580 50
3、017 6National forewordThis British Standard was published by BSI. It is the UK implementation of EN 2349-301:2006.The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Panel ACE/6/-/4, Aerospace Switching devic
4、es.A list of organizations represented on ACE/6/-/4 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from le
5、gal obligations. Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 2349-301October 2006ICS 49.060English VersionAerospace series - Requirements and test procedures for relaysand contactors - Part 301: Pick-up and drop-out voltageSrie arospatia
6、le - Exigences et mthodes dessais desrelais et contacteurs - Partie 301 : Tension de collage et dedcollageLuft- und Raumfahrt - Anforderungen und Prfverfahren frRelais und Schaltschtze - Teil 301: Ansprechspannungund RckfallspannungThis European Standard was approved by CEN on 10 May 2006.CEN member
7、s are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application t
8、o the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same st
9、atus as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia,
10、Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN
11、national Members.Ref. No. EN 2349-301:2006: E2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Pick-up (actuating) voltage.4 4 Drop-out (release) voltage 4 EN 2349-301:20063 Foreword This document (EN 2349-301:2006) has been prepared by the AeroSpace and Defense Industries Association o
12、f Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This Europea
13、n Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2007, and conflicting national standards shall be withdrawn at the latest by April 2007. Attention is drawn to the possibility that some of the elements o
14、f this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European
15、 Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 2
16、349-301:20064 1 Scope This standard specifies a method for testing the pick-up voltage and drop-out voltage of relays and contactors. It shall be used together with EN 2349-100. 2 Normative references The following referenced documents are indispensable for the application of this document. For date
17、d references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2349-100, Aerospace series Requirements and test procedures for relays and contactors Part 100: General requirements 1)3 Pick-up (actuating) volt
18、age 3.1 Mounting method The relay or contactor shall be wired in accordance with EN 2349-100. 3.2 Test procedure The coil shall be left in a de-energized state for 30 min before starting the test. The minimum rate of voltage increase and the time to energize the coil, applicable to the device under
19、test, shall be determined to prevent overheating of the coil. The rated voltage shall be applied to the coil, then reduced to zero, and gradually increased until the relay or contactor picks up. The contacts shall not change their switching position when the voltage is increased from the pick-up vol
20、tage to the maximum operating voltage. An indicating device shall be used to determine the position of the contacts. For qualification tests, the relay or contactor shall be tested in each of two directions along three axes which are perpendicular to each other (i.e. six degrees of freedom). 3.3 Tes
21、t criteria The relay or contactor shall pick up at the rated voltage specified in the product standard. 4 Drop-out (release) voltage 4.1 Mounting method The relay or contactor shall be wired as described in EN 2349-100. 1) In preparation at the date of publication of this standard. EN 2349-301:20065
22、 4.2 Test procedure The coil shall be left in a de-energized condition for 30 min before starting the test. The rated voltage shall be applied to the coil and then gradually reduced until the relay or contactor drops out. The contacts shall not change their switching position when the voltage is red
23、uced from the drop-out voltage to zero. An indicating device shall be used to determine the position of the contacts. For qualification tests the switching device shall be tested in each of the three axes which are perpendicular to each other. 4.3 Test criteria The relay or contactor shall drop-out
24、within the voltage range specified in the product standard. EN 2349-301:2006BS EN 2349-301:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at
25、 the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv
26、ices. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers mem
27、bers an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)2
28、0 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on s
29、tandardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Informat
30、ion Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration.
31、Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BS
32、I publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electr
33、onic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.