1、BRITISH STANDARDBS EN 3061:2007Aerospace series Bearings, airframe rolling Rigid single row ball bearings in corrosion resisting steel, with flanged alignment housing Dimensions and loadsThe European Standard EN 3061:2007 has the status of a British StandardICS 49.035g49g50g3g38g50g51g60g44g49g42g3g
2、58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 3061:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 200
3、7 BSI 2007ISBN 978 0 580 58103 8National forewordThis British Standard is the UK implementation of EN 3061:2007. The UK participation in its preparation was entrusted to Technical Committee MCE/7, Rolling bearings.A list of organizations represented on this committee can be obtained on request to it
4、s secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN ST
5、ANDARDNORME EUROPENNEEUROPISCHE NORMEN 3061June 2007ICS 49.035English VersionAerospace series - Bearings, airframe rolling - Rigid single rowball bearings in corrosion resisting steel, with flanged alignmenthousing - Dimensions and loadsSrie arospatiale - Roulements pour structures daronefs- Rouleme
6、nts en acier rsistant la corrosion, rigides, une range de billes, avec bague dalignement collerette -Dimensions et chargesLuft- und Raumfahrt - Flugwerklager - EinreihigeRillenkugellager aus korrosionsbestndigem Stahl mitselbsteinstellendem Flansch - Mae und BelastungenThis European Standard was app
7、roved by CEN on 16 March 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalst
8、andards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified
9、to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Net
10、herlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation i
11、n any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3061:2007: E2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .5 4 Symbols and abbreviations 5 5 Required characteristics.5 6 Designation 10 7 Marking .10 8 Technical specification .
12、10 EN 3061:20073 Foreword This document (EN 3061:2007) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the
13、National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2007, and conflicting nat
14、ional standards shall be withdrawn at the latest by December 2007. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CE
15、N/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
16、Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 3061:20074 1 Scope This standard specifies the characteristics of rigid single row ball bearings in corrosion resisting steel with a solid or lightweight flang
17、ed alignment housing, designed to withstand only slow rotations and slight oscillations under load. They are intended for use in the hubs of torsion lever and in separated supports for airframe/aerospace applications. The airframe rolling bearings defined in this standard may be used in the temperat
18、ure range from 54 C to 150 C. However, being lubricated with the following greases (see EN 3727): ester type very high pressure grease (code letter A), operating range from 73 C to 121 C or, synthetic hydrocarbons type very high pressure grease general purpose (code letter B) operating range from 54
19、 C to 177 C. Their field of application when lubricated with code letter A grease is limited to 121 C. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the l
20、atest edition of the referenced document (including any amendments) applies. ISO 1132-1, Rolling bearings Tolerances Part 1: Terms and definitions. ISO 8075, Aerospace Surface treatment of hardenable stainless steel parts. EN 2030, Steel FE-PM43 Hardened and tempered Bars D 150 mm Aerospace series.1
21、)EN 2226, Steel FE-PM43 Hardened and tempered Hand and die forgings De 150 mm Aerospace series. 1)EN 2424, Aerospace series Marking of aerospace products. EN 2502, Steel FE-PM66 930 Rm 1 080 MPa Bars De 150 mm Aerospace series. 1)EN 2503, Steel FE-PM66 930 Rm 1 080 MPa Forgings De 150 mm Aerospace s
22、eries. 1)EN 25392), Aerospace series Steel FE-PM3801(X5CrNiCu17-4) Air melted Solution treated and precipitation treated Bar a or D 200 mm Rm 965 MPa.3)EN 3161, Aerospace series Steel FE-PM3801 (X5CrNiCu17-4) Air melted Solution treated and precipitation treated Bar a or D 200 mm Rm 930 MPa. 3)EN 37
23、27, Aerospace series Bearings, airframe rolling rigid with flanged alignment housing Technical specification. 1) Published as ASD Standard at the date of publication of this standard. 2) Inactive for new design, see EN 3161. 3) Published as ASD Prestandard at the date of publication of this standard
24、. EN 3061:20075 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 1132-1 and the following apply. 3.1 bearing full complement of balls (without retainer), with filling slot 4 Symbols and abbreviations dmp= single plane mean bore diameter deviation ds=
25、deviation of a single bore diameter Cs= permissible static radial load Famax.= permissible static axial load Ga= axial internal clearance Gr= radial internal clearance Sia= assembled bearing inner ring face runout with raceway Sea= assembled bearing outer ring face runout with raceway Kia= radial ru
26、nout of assembled bearing inner ring Kea= radial runout of assembled bearing outer ring 5 Required characteristics 5.1 Configuration, dimensions, tolerances, clearances, torques and masses Configuration and values: according to Figures 1 to 4 and Table 1; the bearings can be fitted with either seals
27、 or shields; the flanged alignment housing is either solid or lightweight. The dimensions and tolerances are expressed in millimetres and apply after surface treatment. Key aIn both positions at 180 from the bearing NOTE Broken corners 0,1 to 0,4; the edges of spherical surfaces shall be carefully r
28、ounded off. Figure 1 EN 3061:20076 aTransition area at the manufacturers discretion Figure 2 Solid flanged alignment housing, code letter C Figure 3 Light weight flanged alignment housing, code letter D Type with shields code letter P Type with seals code letter E NOTE 1 Installation of seals and sh
29、ields is at the manufacturers option. NOTE 2 The shields shall not extend beyond width C. Figure 4 EN 3061:20077 Table 1 d Tolerances m A B C D d1E E1r Masses g/pieces Code number nom. dmpdsnom. 0,150 0,12 0,2 0,05 1 1 min.a 1 Code letter CCode letter D16 16 0 8 + 3 11 47 8 6 58 33 35 35 4 0 47 38 2
30、0 20 52 63 38 43 42 330 62 50 25 25 0 10 + 3 13 57 68 43 46 46 3 7 70 58 32 32 66 77 52 56 55 230 94 78 35 35 69 9 7 80 55 59 58 220 12 100 86 40 40 75 86 61 66 64 125 104 45 45 80 91 66 71 68 2 137 114 50 50 0 12 + 3 15 86 10 8 97 72 77 74 140 15 155 129 63 63 0 15 + 4 19 100 11 9 111 86 97 90 0,3
31、to 0,8 130 22 210 178 d Internal clearances bm Runout tolerances bmax. m Tilting torque N.m Starting torquebmax. mN.m Axial max. Radial Axial Radial Code number GaGrSiaSeaKiaKeaCode letter P Code letter E 16 8 12 20 9 14 25 0,8 to 3 12 21 32 2 to 7 21 30 35 1 to 4 27 35 40 33 44 45 1,3 to 4,5 39 53
32、50 1,5 to 5 48 68 63 120 2 to 9 40 40 25 40 2 to 6 83 113 aMaximum values for the user. bSee EN 3727. EN 3061:20078 5.2 Loads See Tables 2 and 3. Table 2 Loads for bearings with code C alignment housing Permissible static loadsa kN Axial Radial Csfor a displacement of max.: for a displacement of max
33、.: d Code number 0,1 mm 0,15 mm 0,2 mm 0,1 mm 0,15 mm 0,2 mm 16 15,2 20 18,7 25 20,6 32 24,5 35 1,32 1,78 2,16 1,8 2,5 3,2 25,5 40 1,3 1,75 2,13 1,78 2,48 3,18 29,5 45 1,27 1,72 2,08 1,75 2,44 3,13 32,4 50 1,2 1,67 2 1,68 2,37 3,03 35,3 63 0,92 1,11 1,29 1,16 1,46 1,78 39,2 aAxial and radial loads m
34、ay be applied simultaneously. For ultimate static loads, see EN 3727. EN 3061:20079 Table 3 Loads for bearings with code D alignment housing Permissible static loadsa kN Axial Radial Csfor a displacement of max.: for a displacement of max.: d Code number 0,1 mm 0,15 mm 0,2 mm 0,1 mm 0,15 mm 0,2 mm 1
35、6 15,2 20 1,15 1,45 1,7 1,32 1,71 2,06 18,7 25 0,92 1,29 1,56 1,22 1,58 1,91 20,6 32 24,5 35 25,5 40 29,5 45 32,4 50 0,84 1,1 1,06 35,3 63 0,99 1,17 1,3 1,18 1,37 1,57 39,2 aAxial and radial loads may be applied simultaneously. For ultimate static loads, see EN 3727. 5.3 Surface roughness Raceways a
36、nd balls: Ra= 0,2 m Bore, side faces of bearing and bearing/housing swivelling surfaces: Ra= 0,8 m Embedding diameter and support face of the housing: Ra= 1,6 m General state: Ra= 3,2 m The values apply prior to surface treatment. EN 3061:200710 5.4 Materials Housing: EN 2502 or EN 2503 or EN 2539,
37、29 HRC to 37 HRC Inner ring: EN 2030 or EN 2226 58 HRC Outer ring: EN 2030 or EN 2226, 58 HRC Balls: EN 2030, 58 HRC Shields: corrosion resisting material Seals: polytetrafluoroethylene (PTFE) or polytetrafluoroethylene (PTFE) reinforced with glass fabric. 5.5 Surface treatment Passivation according
38、 to ISO 8075: code T With no surface treatment: no code 6 Designation EXAMPLE Description block BEARING Identity block EN3061A16PCT Number of this standard Code letter for grease type (see Clause 1) Diameter code number of d (see Table 1) Type code letter (see Figure 4) Alignment housing code letter
39、 (see Figures 2 and 3) Surface treatment code (see 5.5) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 7 Marking According to EN 2424, category A. The marking position is at the manufacturers discretion. 8 Technical specification According to
40、EN 3727. EN 3061:2007blankBS EN 3061:2007BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal
41、Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccu
42、racy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which
43、ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also ava
44、ilable from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on na
45、tional, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8
46、996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Em
47、ail: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the U
48、K, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permissi
