1、BRITISH STANDARD AEROSPACE SERIES Aerospace series - Rivets, solid, 100“ countersunk normal head, in corrosion resisting steel FE-PA2601, passivated, inch based series The European Standard EN 3140:2001 has the status of a British Standard ICs 49.030.60 BS EN 3140:ZOOl NO COPYING WITHOUT BSI PERMISS
2、ION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 3140:2001 Amd. No. National foreword Date Comments This British Standard is the official English language version of EN 3140:2001. The UK participation in its preparation was entrusted to Technical Committee ACEIlBIl, Aerospace Fastener, Fastening Syste
3、ms, Details and Parts (International), which has the responsibility to: - - aid enquirers to understand the text; present to the responsible internationalEuropean committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international
4、 and European developments and promulgate them in the UK. - A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in th
5、e BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are re
6、sponsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. This British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and
7、 comes into effect on 15 September 2001 Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments iss
8、ued since publication O BSI 07-2001 ISBN O 580 37383 5 e EUROPEAN STANDARD NORME EUROPENNE o EUROPISCHE NORM EN 3140 June 2001 ICs 49.030.60 English version Aerospace series - Rivets, solid, 100“ countersunk normal head, in corrosion resisting steel FE-PA2601 , passivated, inch based series Sene aro
9、spatiale - Rivets ordinaires, tte fraise 100“ normale, en acier rsistant la corrosion FE-PA2601, passivs, srie base inches Luft- und Raumfahrt - Vollniete, mit 100“ normalem Senkkopf, aus korrosionsbestndigem Stahl FE-PA2601, passiviert, Zoll-Reihe This European Standard was approved by CEN on 28 Fe
10、bruary 2001. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be o
11、btained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management
12、Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPE
13、AN COMMITEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels O 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3140:2001 E Page 2 EN 314
14、0:2001 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Servi
15、ces of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2001, and conflicting national standards shall be withdrawn at the
16、latest by December 2001. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
17、Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Page 3 EN 31 40:2001 1 Scope This standard specifies the characteristics of solid rivets, with 100“ countersunk normal head, in corrosion resisting steel FE-PA2601, passivated, inch based series, for maximum operating
18、temperature 750 “C. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amen
19、dments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. IS0 10299 EN 2000 Aerospace - Rivets, solid - Material and metric series identi
20、fication Aerospace series - Quality assurance - EN aerospace products - Approval of the quality O system of manufacturers EN 2119 Aerospace series - Heat resisting alloy FE-PA2601 (XGNiCrTiMoV26-15) - Solution treated and precipitation treated - Wires for rivets - 2 mm I DI 10 mm - m 2 900 MPa 1) EN
21、 2424 EN 2516 Aerospace series - Marking of aerospace products Aerospace series - Passivation of corrosion resisting steels and decontamination of nickel base alloys EN 2898 Aerospace series - Corrosion and heat resisting steel rivets - Technical specification 1) 3 Required Characteristics 3.1 See f
22、igure 1 and tables 1 and 2. Dimensions and tolerances are: expressed in millimetres and apply after surface treatment. Configuration - Dimensions - Masses 3.2 Material EN 21 19 3.3 Surface treatment EN 2516 1) Published as AECMA Prestandard at the date of publication of this standard Page 4 EN 3140:
23、2001 Non-radiused tail (code “N“) Key 1 2 3 a Rounded edge permissible within limiting dimensions Area of this datum shall be between 5 and S + 1. Chamfer or convex radius, at manufacturers option Drill start (code 1) optional, shape optional Figure 1 Table 1 Radiused tail (code “R“) 3 a DI ma. may
24、increase by 0,03, over length (4 - L2). Maximum condition Page 5 EN 3140: 2001 O O O O O O O g c n u) u) 0 2“ z m- n u) u) Q P z m- n u) u) Q s= z m- n u) u) 0 d“ z m- n u) u) Q -= z m- n u) u) Q := z m- n u) u) m s= z m- n u) u) ES mZ 30 :s QJ Q) o+ m 4- c- Q)Q) ZI O o Page 6 EN 31 40:2001 4 Design
25、ation EXAMPLE: Description block Identity block RIVET EN31 40-024009Rl Number of this standard Diameter code (see table 1) Length code (see table 2) Tail end code (see figure 1) Drill start code (see figure 1) NOTE If necessary, the code 19005 shall be placed between the description block and the id
26、entity block. 5 Marking 5.! Rivet EN 2424, style G 5.2 Material IS0 10299 6 Technical specification IS0 2898, plus EN 2000 for the approval of manufacturers BS EN 3140:ZOOl BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible f
27、or preparing O British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments
28、or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on
29、 the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications
30、should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at httP:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Sta
31、ndards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details o
32、n all its products and services. Contact the Information Centre. Tel 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Mem
33、bership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at httP:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bod
34、ies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the
35、free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.
