1、BRITISH STANDARDBS EN 3475-501:2006Aerospace series Cables, electrical, aircraft use Test methods Part 501: Dynamic cut-throughThe European Standard EN 3475-501:2006 has the status of a British StandardICS 49.060g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g4
2、4g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 3475-501:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2006 BSI 2006ISBN 0 580 49430 6National forewordThis
3、 British Standard was published by BSI. It is the UK implementation of EN 3475-501:2006. It supersedes BS EN 3475-501:2002 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Subcommittee
4、ACE/6/-/2, Aerospace Cables.A list of organizations represented on ACE/6/-/2 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard canno
5、t confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 3475-501June 2006ICS 49.060 Supersedes EN 3475-501:2002 English VersionAerospace series - Cables, electrical, aircraft use - Testmethods - Part 501: Dyn
6、amic cut-throughSrie arospatiale - Cbles lectriques usagearonautique - Mthodes dessai - Partie 501 : Rsistance la coupureLuft- und Raumfahrt - Elektrische Leitungen frLuftfahrtverwendung - Prfverfahren - Teil 501:KerbfestigkeitThis European Standard was approved by CEN on 20 April 2006.CEN members a
7、re bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to t
8、he Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same statu
9、s as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slo
10、venia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN nat
11、ional Members.Ref. No. EN 3475-501:2006: E2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Preparation of specimens.4 4 Apparatus .4 5 Method 5 6 Requirements.5 EN 3475-501:20063 Foreword This European Standard (EN 3475-501:2006) has been prepared by the European Association of Aerospa
12、ce Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN.
13、This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2006, and conflicting national standards shall be withdrawn at the latest by December 2006. Attention is drawn to the possibility that some
14、 of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 3475-501:2002. According to the CEN/CENELEC Internal Regulations, the national standards organizations of
15、 the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slov
16、enia, Spain, Sweden, Switzerland and the United Kingdom. EN 3475-501:20064 1 Scope This standard specifies a method of measuring the resistance to cut-through of an insulated conductor or jacket. This test is limited to cables smaller than code 140 (gauge size 6) and insulations with a thickness of
17、0,38 mm or less. It shall be used together with EN 3475-100. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (
18、including any amendments) applies. EN 3475-100, Aerospace series Cables, electrical, aircraft use Test methods Part 100: General. 3 Preparation of specimens The test specimen shall be a single 450 mm length of insulated cable. Remove sufficient insulation from one end of the specimen for connection
19、to the detection circuit. 4 Apparatus A tensile tester (or equivalent apparatus) shall operate in a compression mode and be equipped with a means to record the force necessary to drive the cutting edge through the insulation of a finished cable specimen. The cutting edge shall be positioned across t
20、he specimen at 90 to its longitudinal axis and shall have the dimensions shown in Figure 1. The tester shall also be equipped with a chamber that allows the test to be performed after stabilisation at elevated temperatures, and a low voltage detection circuit shall stop the tester when the edge cuts
21、 through the insulation and contacts the conductor. EN 3475-501:20065 Figure 1 Needle holder 5 Method Carry out the test at the temperature specified in the applicable product standard. At elevated temperatures the apparatus must be stabilised prior to each test which may require up to one hour (1 h
22、) depending upon chamber and specimen size. Move the cutting edge through the insulation at a constant rate of loading of (1 0,1) N/s at the specimen until contact with the conductor occurs. Move the specimen longitudinally a minimum of 25 mm and rotate it 90 between each test, keeping the direction
23、 of movement and rotation constant. Perform eight individual tests on the specimen. Record the force at cut-through for each test. 6 Requirements The arithmetic mean value of the eight measured cut-through results shall exceed the value given in the product standard. EN 3475-501:2006BS EN 3475-501:2
24、006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are
25、 updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Bri
26、tish Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically
27、 receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/w
28、ww.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international sta
29、ndards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing
30、members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regard
31、ing online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internat
32、ional standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This do
33、es not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.
