1、BRITISH STANDARDBS EN 3645-005:2006Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 005: Receptacle, hermetic, round flange, brasage mounting Product standardThe European Standard EN 3645-005:2006 has
2、 the status of a British StandardICS 49.060g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 3645-005:2006This British Standard was published un
3、der the authority of the Standards Policy and Strategy Committee on 31 January 2007 BSI 2007ISBN 978-0-580-49949-4National forewordThis British Standard was published by BSI. It is the UK implementation of EN 3645-005:2006.The UK participation in its preparation was entrusted by Technical Committee
4、ACE/6, Aerospace avionic electrical and fibre optic technology, to Subcommittee ACE/6/-/3, Aerospace Connectors.A list of organizations represented on ACE/6/-/3 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users
5、are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3645-005 December 2006 ICS 49.060 English Version Aerospace serie
6、s - Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous - Part 005: Receptacle, hermetic, round flange, brasage mounting - Product standard Srie arospatiale - Connecteurs lectriques circulaires contacts protgs, accouplement p
7、ar filetage pas rapide trois filets, tempratures dutilisation 175 C ou 200 C continu - Partie 005 : Embase hermtique collerette ronde fixation par brasage - Norme de produit Luft- und Raumfahrt - Elektrische Rundsteckverbinder, kontaktgeschtzt, Drei-gangige Gewinde-Schnellkupplung, Dauerbetriebstemp
8、eraturen 175 C oder 200 C - Teil 005: Hermetischer fester Steckverbinder mit runden Schwei - Produktnorm This European Standard was approved by CEN on 28 September 2006. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
9、Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, Fre
10、nch, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Repu
11、blic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE
12、 NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3645-005:2006: E2 Contents Page Foreword3 1 Scope 4 2 Normative references 4
13、3 Terms and definitions .4 4 Required characteristics.5 5 Designation 7 6 Marking .8 7 Technical specification .8 EN 3645-005:20063 Foreword This document (EN 3645-005:2006) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries
14、and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national stan
15、dard, either by publication of an identical text or by endorsement, at the latest by June 2007, and conflicting national standards shall be withdrawn at the latest by June 2007. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN
16、and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denm
17、ark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 3645-005:20064 1 Scope This standard specifies the charact
18、eristics of round flange hermetic receptacles, mounted by soldering, in the family of circular electrical connectors with triple start threaded coupling. It applies to models in Table 3. The contacts are unremovable and soldered termination. For plugs and protective covers, see EN 3645-008, EN 3645-
19、011, EN 3645-012 and EN 3645-006 respectively. These connectors are derived from and interchangeable with model Y in specification MIL-DTL-38999/25. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the editio
20、n cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3645-001, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 001: Technical
21、specification. EN 3645-002, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 002: Specification of performance and contact arrangements. EN 3645-006, Aerospace series Connectors, electrical, circular,
22、 scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 006: Protective cover for receptacle Product standard. EN 3645-008, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C
23、continuous Part 008: Non release plug with grounding ring Product standard. EN 3645-011, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 011: Lanyard release plug with grounding fingers Type 1 Produc
24、t standard. EN 3645-012, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 012: Lanyard release plug with grounding fingers Type 2 Product standard. MIL-DTL-38999/25, Connector, electrical, circular, t
25、hreaded, receptacle, solder mounting, hermetic, hermetic solder contacts, series III, metric. 1)3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN 3645-001 apply. 1) Published by: Department of Defense (DOD), The Pentagon, Washington D.C. 20301 USA. EN 3
26、645-005:20065 4 Required characteristics 4.1 Dimensions and mass See Figure 1 and Table 1. Dimensions and tolerances are in millimetres. Key 1 Red strip 2 Male contact Female contact Figure 1 Round flange receptacle EN 3645-005:20066 Table 1 Round flange receptacle Dimensions F N S Z Stainless steel
27、 mass g Shell size max. max. max. max. max. 09 17,10 19,40 15 11 19,90 21,80 20 13 23,10 24,90 25 15 26,20 28,10 31 17 29,40 31,30 38 19 31,80 33,60 44 21 35,00 5,1036,80 23,8051 23 38,20 40,00 60 25 41,30 5,90 43,20 24,60 71 4.2 Materials and surface treatment See Table 3. 4.3 Recommended panel cut
28、-out See Figure 2 and Table 2. Dimensions and tolerances are in millimetres. Figure 2 Panel cut-out EN 3645-005:20067 Table 2 Panel cut-out Dimensions A Shell size + 0,25 0 09 17,20 11 20,00 13 23,20 15 26,30 17 29,50 19 31,90 21 35,10 23 38,30 25 41,40 4.4 Electrical, mechanical and climatic charac
29、teristics See EN 3645-002. 5 Designation EXAMPLE Description block ELECTRICAL CONNECTOR Identity block EN3645-Y1GN35MA Number of the basic standard Model (see Table 3) Shell code for hermetic, round flange receptacle, attached by soldering Shell size code (see Table 4) N: no earthed contacts Contact
30、 arrangement (see EN 3645-002) except those containing coaxial or triaxial contacts or size 10 contacts Contact code M: male with solder cup X: male with eyelet Polarization: N, A, B, C, D, E NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. EN 3
31、645-005:20068 Table 3 Model coding Model Description Y Sealed receptacles, with shell in stainless steel Soldered contacts Maximum operating temperature 200 C continuous. Table 4 Shell size code Shell size Code 09 A 11 B 13 C 15 D 17 E 19 F 21 G23 H 25 J 6 Marking According to EN 3645-001. 7 Technic
32、al specification According to EN 3645-001. EN 3645-005:2006blankBS EN 3645-005:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the interna
33、tional level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We wou
34、ld be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an indi
35、vidual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001.
36、 Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI
37、provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre.
38、Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)
39、20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publicatio
40、ns. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photoc
41、opying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.
