1、BRITISH STANDARDBS EN 4592:2006Aerospace series Paints and varnishes Test method for determination of infrared reflectanceThe European Standard EN 4592:2006 has the status of a British StandardICS 49.040g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3
2、g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 4592:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2006 BSI 2006ISBN 0 580 49534 5National forewordThis British Sta
3、ndard was published by BSI. It is the UK implementation of EN 4592:2006.The UK participation in its preparation was entrusted by Technical Committee ACE/65, Non-metallic materials for aerospace purposes (excluding textiles), to Subcommittee ACE/65/-/3, Paints.A list of organizations represented on A
4、CE/65/-/3 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since pu
5、blicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 4592October 2006ICS 49.040English VersionAerospace series - Paints and varnishes - Test method fordetermination of infrared reflectanceSrie arospatiale - Peintures et vernis - Mthode dessaipour rflectance infrarougeLuft
6、- und Raumfahrt - Anstrichstoffe - Prfmethode zurMessung der InfrarotremissionThis European Standard was approved by CEN on 21 July 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national
7、standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other
8、 language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France
9、,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUN
10、GManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 4592:2006: E2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Principle4 5 Apparatus
11、 .4 6 Specimen 5 7 Procedure .5 8 Designation 6 9 Test report 6 EN 4592:20063 Foreword This document (EN 4592:2006) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this
12、 Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by end
13、orsement, at the latest by April 2007, and conflicting national standards shall be withdrawn at the latest by April 2007. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identif
14、ying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
15、 Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 4592:20064 1 Scope This standard specifies the method of test for determining the infrared reflectance of paints a
16、nd varnishes. The test procedure determines the amount of energy reflected by the material in the range of wavelengths between 700 nanometres and 2 400 nanometres with respect to that of a standard reflectance material. The procedure is applicable to products intended for use in aerospace applicatio
17、ns. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1513, Paints and v
18、arnishes Examination and preparation of samples for testing. ISO 2808, Paints and varnishes Determination of film thickness. ISO 3270, Paints and varnishes and their raw materials Temperatures and humidities for conditioning and testing. ISO 15528, Paints, varnishes and raw materials for paints and
19、varnishes Sampling. 3 Terms and definitions For the purposes of this standard, the following definitions apply. 3.1 infrared reflectance the proportion of the energy reflected by a specimen in relation to a defined standard material 4 Principle The reflectance of a specimen comprising a coated test
20、panel is measured against that of reflectance standard in the 700 nm to 2 400 nm wavelength range. 5 Apparatus A recording spectrophotometer fitted with an integrating sphere which will meet the following requirements unless otherwise specified or agreed (see Table 1). EN 4592:20065 Table 1 Measurem
21、ent range 700 nm to 2 400 nm minimum Wavelength accuracy 5 nm Measurement accuracy (700 nm to 2 100 nm) 2 % (2 100 nm to 2 400 nm) 8 % Bandpass 4 nm at 700 nm rising to a maximum of 14 nm at 2 400 nm Integrating sphere geometry (reference conditions in case of dispute) (10 2)/diffuse specular compon
22、ent included A reference material of known reflectance in the range 700 nm to 2 400 nm. 6 Specimen Take a representative sample of the product to be tested or of each component in the case of a multi-coat system as described in ISO 15528. Examine and prepare the sample for testing as described in IS
23、O 1513. The test panel shall be of a size suitable for the performance of the tests identified by this and the product standard. Coat the test panel with the test product as specified by the product standard. Dry/cure the coating for the time and under the conditions specified in the product standar
24、d. The coating thickness, when determined using one of the non destructive procedures specified in ISO 2808 shall comply with the requirements of the product standard. Condition the test panels in accordance with ISO 3270 for a minimum of 16 hours and a maximum of 72 hours prior to testing. 7 Proced
25、ure 7.1 Operation Operate the spectrophotometer in accordance with the manufacturers recommendations for environmental conditions, method of operation and calibration if different from that below. 7.2 Calibration Place the reflectance standard over the reference port of the integrating sphere. Block
26、 the sample beam before it enters the integrating sphere using a suitable device and obtain a 0 % baseline in the specified wavelength range. Note that with some spectrophometers it may be possible to calibrate the baseline so that no correction is necessary to the sample spectrum. Remove the sample
27、 port blocking device and place reflectance standards over both the reference and sample ports and obtain the 100 % baseline in the specified wavelength range. If the absolute reflectance spectrum is required, correct the spectrum to 100 % using the correction factors for the reflectance standard us
28、ed. EN 4592:20066 7.3 Measurement Replace the sample port reflectance standard with the test panel and record the sample reflectance spectrum over the specified wavelength range. If the absolute reflectance spectrum is required, correct the spectrum using the correction factors for the reflectance s
29、tandard used. If specified, compare the recorded spectrum with that of the comparison spectrum. 8 Designation EXAMPLE Description block DETERMINATION OF INFRARED REFLECTANCE Identity block EN4592 Number of the standard 9 Test report 9.1 Basic information The test report shall contain at least the fo
30、llowing information: a) all details necessary to identify the product tested; b) reference to this test standard; c) reference to the product standard; d) items of supplementary information (9.2); e) results of the test work in terms of the stated requirements; f) any deviation from the test method
31、specified; g) date(s) of the test; h) name of operator. EN 4592:20067 9.2 Supplementary information In the performance of this test standard there is a requirement for supplementary information to be provided by the product standard for the material under test. This information consists of: a) subst
32、rate type and method of preparation; b) method of application of the coating including, where applicable, the duration and conditions of drying/curing between coats in the case of multi-coat systems; c) duration and conditions of drying/curing of the final coat before test; d) thickness of the dry c
33、oating or combination of coatings in micrometres; e) wavelength range to be measured; f) instrument geometry if different from that defined in this standard; g) standard reflectance material to use; h) whether the spectrum is to be corrected to absolute reflectance; i) spectrum that the sample is to
34、 be compared to (if required). EN 4592:2006BS EN 4592:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incor
35、porated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone
36、finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service c
37、alled PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Stand
38、ards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of
39、information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111.
40、 Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0
41、)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the co
42、pyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or othe
43、rwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.
