1、BS EN 508-3:2008ICS 91.060.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDRoofing productsfrom metal sheet Specification for selfsupporting productsof steel, aluminium orstainless steel sheetPart 3: Stainless steelThis British Standardwas published under thea
2、uthority of the StandardsPolicy and StrategyCommittee on 31 March2009 BSI 2009ISBN 978 0 580 59451 9Amendments/corrigenda issued since publicationDate CommentsBS EN 508-3:2008National forewordThis British Standard is the UK implementation of . It supersedes BSEN 508-3:2000 which is withdrawn.The UK
3、participation in its preparation was entrusted to TechnicalCommittee B/542/5, Sheet roof and wall coverings.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users a
4、re responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.EN 508-3:2008BS EN 508-3:2008EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 508-3July 2008ICS 91.060.20 Supersedes EN 508-3:2000 English VersionRoofing products from metal sh
5、eet - Specification for self-supporting products of steel, aluminium or stainless steel sheet -Part 3: Stainless steelProduits de couverture en tle mtallique - Spcificationpour les plaques de couverture en tle dacier, daluminiumou dacier inoxydable - Partie 3 : Acier inoxydableDachdeckungsprodukte a
6、us Metallblech - Festlegungen frselbsttragende Bedachungselemente aus Stahlblech,Aluminiumblech oder nichtrostendem Stahlblech - Teil 3:Nichtrostendes StahlblechThis European Standard was approved by CEN on 30 May 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which s
7、tipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard
8、 exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards
9、 bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.E
10、UROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 508-3:2008: EBS EN 508-3:200
11、8EN 508-3:2008 (E) 2 Contents Page Foreword4 Introduction .5 1 Scope 6 2 Normative references 6 3 Terms and definitions, symbols and abbreviations.6 3.1 General6 3.2 Materials .6 3.3 Profiles7 3.4 Product geometry 9 3.5 Symbols and abbreviations 13 4 Requirements.13 4.1 General13 4.2 Materials .13 4
12、.2.1 Grades.13 4.2.2 Chemical composition 14 4.2.3 Physical properties14 4.2.4 Surface finishes of stainless steel.14 4.2.5 Tin coated stainless steel .14 4.2.6 Organic coated stainless steel.14 4.3 Products .15 4.3.1 Mechanical resistance.15 4.3.2 Calculation and tests of mechanical resistance.15 4
13、.3.3 Dimensions.15 4.3.4 Dimensional tolerances for the profiled sheets .16 4.3.5 Safety in case of fire16 5 Test methods16 5.1 Material properties.16 5.2 Structural properties .16 6 Designation 16 7 Marking, labelling and packaging 17 7.1 Marking and labelling 17 7.2 Packaging and special ordering
14、conditions .17 7.3 Transport, storage and handling17 Annex A (informative) Physical properties.18 Annex B (normative) Dimensional tolerances .19 B.1 Tolerances for trapezoidal sheets19 B.1.1 General19 B.1.2 Depth of profile 19 B.1.3 Depth of stiffeners .20 B.1.4 Pitch 20 B.1.5 Widths of crown and va
15、lley 21 B.1.6 Cover width 21 B.1.7 Radius of bends.22 B.1.8 Deviation from straightness .23 B.1.9 Deviation from squareness.24 B.1.10 Length .24 B.1.11 Deviation of side lap25 BS EN 508-3:2008EN 508-3:2008 (E) 3 B.1.12 Curve radius and angles.25 B.2 Tolerances for sinusoidal profiles.26 B.3 Toleranc
16、es on tiles 26 B.3.1 General .26 B.3.2 Depth of tile27 B.3.3 Web angular displacement (Figure B.12)28 B.3.4 Pitch28 B.3.5 Width of crown and valley (Figure B.14).29 B.3.6 Cover width 29 B.3.7 Radius of bends.29 B.3.8 Deviation from straightness.30 B.3.9 Deviation from squareness 31 B.3.10 Length.31
17、B.3.11 Contraction or bulging31 B.4 Methods for measuring profiles.32 B.4.1 General .32 B.4.2 Depth of profile 32 B.4.3 Depth of stiffeners.33 B.4.4 Pitch33 B.4.5 Width of crown and valley 34 B.4.6 Cover width 34 B.4.7 Radius of bends.34 B.4.8 Straightness.34 B.4.9 Squareness 34 B.4.10 Length.35 B.4
18、.11 Side laps.35 B.4.12 Side lap ripple 35 Annex C (informative) Test methods for concentrated load 37 Bibliography38 BS EN 508-3:2008EN 508-3:2008 (E) 4 Foreword This document (EN 508-3:2008) has been prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying and pr
19、oducts for wall cladding”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2009, and conflicting national standards shall be withdrawn at the lates
20、t by January 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 508-3:2000. EN 508 Roofing products fro
21、m metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet consists of the following parts: Part 1: Steel; Part 2: Aluminium; Part 3: Stainless steel. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
22、 countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia
23、, Spain, Sweden, Switzerland and the United Kingdom. BS EN 508-3:2008EN 508-3:2008 (E) 5 Introduction Figure 1 indicates the position of this standard in the CEN framework of standards concerning roofing products of metal. Roofing products of metal Self-supporting products Fully supported products E
24、N 14782 Copper / Zinc EN 506 Steel EN 508-1 Aluminium EN 508-2 Stainless steel EN 508-3 Figure 1 Framework of standards In this standard the performance of the product has been defined in terms of calculation and a number of type tests. The performance of a roof constructed with these products depen
25、ds not only on the properties of the product as required by this standard, but also on the design, construction and performance of the roof as a whole in relation to the environment and conditions of use. BS EN 508-3:2008EN 508-3:2008 (E) 6 1 Scope This Part of EN 508 specifies requirements for self
26、-supporting roofing products for discontinuous laying made from stainless steel sheet with or without additional metallic and/or organic coatings. The standard establishes general characteristics, definitions, classifications and labelling for the products, together with requirements for the materia
27、ls from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply before they are despatched from the factory. It specifies the requirements for products whi
28、ch enable them to meet all normal service conditions. The standard applies to all discontinuously laid self-supporting external profiled sheets for roofing with the exception of tiles with a surface area less than 1 m2and produced by stamping. These profiled roof sheets are designed to keep wind, ra
29、in and snow out of the building and to transfer any resultant loads and infrequent maintenance loads to the structure. No requirements for supporting construction, design of roof system and execution of connections and flashings are included. 2 Normative references The following referenced documents
30、 are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10088-1, Stainless steels - Part 1: List of stainless steels EN 10088-2, Stainle
31、ss steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes EN 10202, Cold reduced tinmill products Electrolytic tinplate and electrolytic chromium/chromium oxide coated steel EN ISO 9445, Continuously cold-rolled stainless steel nar
32、row strip, wide strip, plate/sheet and cut lengths - Tolerances on dimensions and form (ISO 9445:2002) 3 Terms and definitions, symbols and abbreviations For the purposes of this document, the following terms and definitions apply. 3.1 General 3.1.1 self-supporting product Product which will, by vir
33、tue of its material and shape, support all applied loadings (e.g. snow, wind, foot traffic) and transmit these loadings to spaced structural supports. 3.2 Materials 3.2.1 stainless steel steel sheets with at least a content of 10,5 % chromium and max 1,2 % carbon NOTE For roofing products the stainl
34、ess steel grades are: BS EN 508-3:2008EN 508-3:2008 (E) 7 ferritic; austenitic with or without molybdenum; austenitic ferritic (duplex); and higher alloyed grades. 3.2.2 terne coated stainless steel stainless steel continuously hot dip coated with a lead-tin alloy 3.2.3 tin coated stainless steel st
35、ainless steel continuously coated with tin by electrodeposition 3.2.4 organic coated stainless steel stainless steel, terne coated stainless steel or tin coated stainless steel which is continuously (factory-)painted by roller or spray process NOTE EN 10169-1 refers to this type of coated steel. 3.3
36、 Profiles 3.3.1 trapezoidal profiled sheet self-supporting sheet which is designed to allow it to be side and end lapped, the crowns of which may be rounded and, in addition, the crowns, webs and valleys may be stiffened NOTE See Figures 2 to 5. Figure 2 Part of typical trapezoidal profile Figure 3
37、Part of typical trapezoidal profile with rounded crowns Figure 4 Part of typical trapezoidal profile with stiffened crown and web BS EN 508-3:2008EN 508-3:2008 (E) 8 Figure 5 Part of typical trapezoidal profile with stiffened valley 3.3.2 sinusoidal profiled sheet self-supporting sheet which is desi
38、gned to allow it to be side and end lapped, comprising a series of arc shaped crowns and valleys interconnected with tangential webs NOTE See Figure 6. Figure 6 Part of typical sinusoidal profiled sheet 3.3.3 standing seam and concealed fix sheet self-supporting sheet profiled in such a way that the
39、 fixings are hidden within the construction and are not exposed to the weather NOTE 1 See Figures 7 and 8. NOTE 2 The profile shape is designed to allow the formation of side laps on site. NOTE 3 As these types of roof covering products are used in proprietary roofing systems, no structural requirem
40、ents are given within the present standard. NOTE 4 These products are normally designed by testing. Figure 7 Typical standing seam profile BS EN 508-3:2008EN 508-3:2008 (E) 9 Figure 8 Typical concealed fix profile 3.3.4 tile profiles parts of typical tile profiled sheets that can allow the sheet to
41、be side and/or end lapped NOTE 1 See figures 9a, 9b and 9c. NOTE 2 The tile profiles may include transverse steps. NOTE 3 As these types of roof covering products are used in proprietary systems no structural requirements are given within this standard. NOTE 4 These products are normally designed by
42、 testing. Figure 9 Typical tile profiles 3.4 Product geometry NOTE The names for various parts of typical trapezoidal profiled sheets are given in Figures 10a) and 10b), with additional definitions for sinusoidal profiles in Figure 11 and tile profiles in Figure 12. BS EN 508-3:2008EN 508-3:2008 (E)
43、 10 Key 1 Cover width 7 Depth 2 Valley stiffener 8 Valley 3 Rib 9 Pitch 4 Web stiffener 10 Crown 5 Trough 11 Drainage groove 6 Web 12 Crown stiffener a) Definitions of the parts of typical trapezoidal profiled sheets BS EN 508-3:2008EN 508-3:2008 (E) 11 Key 1 Bend radius 4 Overlap 2 End lap 5 Underl
44、ap 3 Web angle 6 Side lap in principle the same on tiles b) Definitions of the parts of typical trapezoidal profiled sheets Figure 10: Definitions of the parts of typical profiled sheets BS EN 508-3:2008EN 508-3:2008 (E) 12 Key 1 Depth 2 Pitch Figure 10 Definitions of the parts of typical sinusoidal
45、 profiled sheets Key 1 Height of the step 2 Length of the step 3 Number of steps 4 End lap Figure 11 Definitions of the parts of typical tile BS EN 508-3:2008EN 508-3:2008 (E) 13 3.5 Symbols and abbreviations X Stainless steel X. +T Terne coated stainless steel X .+SE Terne coated stainless steel SP
46、 Polyester paint coating SP-SI Silicone-modified polyester paint coating PVDF Polyvinylidene fluoride paint coating PUR Polyurethane paint coating PUR-PA Polyurethane-modified polyester paint coating PVC(P) Polyvinylchloride(plastisol) coating applied by coil coating process PVC(F) Polyvinylchloride
47、 (plastisol) film coating PVF(F) Polyvinylfluoride film coating PE(F) Polyethylene film coating PET(F) Polyethylene terephthalate film coating PP(F) Polypropylene film coating 4 Requirements 4.1 General The product shall be manufactured from materials complying with Subclause 4.2 NOTE 1 The supplier
48、 of the materials is responsible for carrying out the tests necessary to verify that the materials supplied to the manufacturer comply with the requirements and should provide appropriate inspection documents (according to EN 10204) on request. NOTE 2 The symbols and abbreviations to be used to desi
49、gnate the steel grade, the type and mass of the metallic coating are those of the standards referred to in clause 2. Product testing shall be provided to a defined schedule and carried out by the manufacturer or by an approved body. A permanent quality system shall be adopted by the manufacturer1). 4.2 Materials 4.2.1 Grades The grades of stainless steel shall be selected depending on the corrosion conditions of the local environment, durability requirements and aesthetic considerations. 1) E.g. quality management system based on
