EN 526-1993 en Inland Navigation Vessels - Gangways with a Length Not Exceeding 8 m - Requirements Types《内河航运船只 长度8 m以下登陆桥 要求 类型》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DIN 764-2-2010 Round steel link chains - Round steel link chains for chain conveyors - Part 2 Grade 5《圆钢铰接链 链式输送机用圆钢铰接链 第2部分 5级》.pdf

DIN 7640-1985 Compression couplings with spherical liner equal crosses《带球形衬的压接管接头 等长度四通连接管》.pdf

DIN 7642-1997 Compression couplings - Ring type nipples for brazed connection《管螺纹连接 钎焊连接环形管接头》.pdf

DIN 7643-2005 Compression couplings - Hollow screws for ring-type banjos《压紧联轴节 环形鼓形管用空心螺钉》.pdf

DIN 7644-1985 Compression couplings with spherical liner male studed banjo bolts for ring type nipples《带球形衬的压接管接头 环形套管的插桩式鼓形螺栓》.pdf

DIN 7647-1995 Compression couplings with spherical liners - Adaptors with parallel screwed-in ends《带球形衬里的压紧联轴节 平行旋入式接头》.pdf

DIN 766-2015 Round steel link chains - Round steel link chains pitch 2 8d for chain conveyors grade 3 quenched and tempered《圆钢环链 链式输送机用节距为2 8d的经淬火和回火的3级圆钢环链》.pdf

DIN 770-1-1962 Shank Sections for Lathe and Planer Tools Rolled and Forged Shanks《车床和刨床刀柄截面 第1部分 轧制和锻制刀柄》.pdf

DIN 770-2-1962 Shank Sections for Lathe and Planer Tools Machined All Over Not Required to Meet Special Standards of Accuracy《车刀和刨刀用刀柄部分 对满足特殊精度标准无要求的全部机加工》.pdf