1、Aerospace series - Blind bolt, 100 flush head, high strengthBS EN 6128:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 6128 October 2017 ICS 49.030.99 English Version Aerospace series - Blind bolt, 100 flush he
2、ad, high strength Srie arospatiale - Boulon aveugle tte fraise 100, haute rsistance Luft- und Raumfahrt - Blindniet 100 Senkkopf, hochfetThis European Standard was approved by CEN on 2 July 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions
3、 for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in t
4、hree official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards
5、bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia,
6、Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means rese
7、rved worldwide for CEN national Members. Ref. No. EN 6128:2017 ENational forewordThis British Standard is the UK implementation of EN 6128:2017.The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems.A list of organizations repre
8、sented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 58
9、0 98089 3ICS 49.030.99Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STA
10、NDARDBS EN 6128:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 6128 October 2017 ICS 49.030.99 English Version Aerospace series - Blind bolt, 100 flush head, high strength Srie arospatiale - Boulon aveugle tte fraise 100, haute rsistance Luft- und Raumfahrt - Blindniet 100 Senkkopf, hochfe
11、tThis European Standard was approved by CEN on 2 July 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical refere
12、nces concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN
13、member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
14、 France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION E
15、UROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 6128:2017 EBS EN 6128:2017EN 6128:2017 (E) 2 Contents Page European foreword . 3 1
16、Scope 4 2 Normative references 4 3 Requirements . 4 3.1 Configuration, dimensions and tolerances 4 3.2 Grip range and weight . 4 3.3 Material, finish and lubrication . 5 4 Designation. 13 5 Marking 14 6 Technical specification . 14 BS EN 6128:2017EN 6128:2017 (E) 3 European foreword This document (E
17、N 6128:2017) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Ser
18、vices of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2018, and conflicting national standards shall be withdrawn at the lat
19、est by April 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organiza
20、tions of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Mal
21、ta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 6128:2017EN 6128:2017 (E) 4 1 Scope This European Standard specifies the configuration, dimension, tolerances and mass of a stainless steel blind bolt with
22、 100 flush head for aerospace application. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of t
23、he referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products EN 4473, Aerospace series Aluminium pigmented coatings for fasteners Technical specification1)AS 5272, Lubricant, Solid Film, Heat Cured, Corrosion Inhibiting, Procurement Specification
24、2)AMS 5687, Nickel Alloy, Corrosion and Heat Resistant, Wire 74Ni 15.5Cr 8.0Fe, Annealed2)AMS 5690, Steel, Corrosion and Heat Resistant, Wire 17Cr-12Ni-2.5Mo (316) Solution Heat Treated2) AMS 5737, Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings and Tubing 15Cr 25.5Ni 1.2Mo 2.1Ti 0.006B 0.
25、30V, Consumable Electrode Melted, 1650 F (899 C), Solution and Precipitation Heat Treated2)AMS-QQ-P-35, Passivation Treatments for Corrosion-Resistant Steel2)MIL-PRF-46010, Lubricant, Solid Film, Heat Cured, Corrosion Inhibiting NATO Code S-17383)MIL-L-87132, Lubricant, CETYL Alcohol, 1-Hexadecanol,
26、 Application to Fasteners3)NASM 8975, Fastener, blind, high strength, installation formed corrosion resistant steel, heat resistant steel and titanium General specification for3)DOD-L-85645, Lubricant, dry film, molecular bonded3)3 Requirements 3.1 Configuration, dimensions and tolerances The config
27、uration, dimensions, tolerances, static and dynamic values shall conform to Figure 1 and Figure 2 and Table 1 and Table 2. 3.2 Grip range and weight See Table 3 and Table 4. 1) Published as ASD-STAN pre-standard at the date of publication of the present standard. www.asd-stan.org 2) Published by: So
28、ciety of Automotive Engineers (SAE), 400 Commonwealth drive, Warrendale, PA 15096-0001, USA 3) Published by: Department of Defense (DOD), the Pentagon, Washington, D.C. 20301. BS EN 6128:2017EN 6128:2017 (E) 5 3.3 Material, finish and lubrication See Table 5 and Table 6. BS EN 6128:2017EN 6128:2017
29、(E) 6 Detail of serrated pin geometry: Detail A Detail A Optional configuration Key 1 Marking see clause 5 2 Serrated pin 3 Sleeve 4 Grip 5 Locking collar 6 Shifting Anvil 7 Drive washer a Diameter of pin head shall not exceed “ D” max. b Fasteners are supplied with shifting anvil / drive washer of
30、manufacturers option. The shifting anvil / drive washer is not part of the installed fastener. Figure 1 Configuration Dimensions BS EN 6128:2017EN 6128:2017 (E) 7 Key 1 Grip a Blind side head may be installed on 7 max slope; 5 max slope for diameter code 10 and 12. Figure 2 Typical installation BS E
31、N 6128:2017EN 6128:2017 (E) 8 Table 1 Dimensions and tolerances Dimensions in mm (inch) Diameter code A B C D Ja N Q D1D2W H PbP2Theor. max. Ref. Ref. max. 0,025 (.001) 0,127 (.005) 1,52 (.060) 0,13 (.005) max. max. Gage dia. Gage height max. min. 05 8,48 (.334) 1,88 (.074) 0,28 (.011) 4,14 (.163) 9
32、,53 (.375) 3,56 (.140) 1,70 (.067) 3,05 (.120) 2,16 (.085) 7,193 7,188 (.2832) (.2830) 0,523 0,434 (.0206) (.0171) 7,62 (.300) 5,66 (.223) 06 9,83 (.387) 2,08 (.082) 0,33 (.013) 5,03 (.198) 9,53 (.375) 4,06 (.160) 2,21 (.087) 3,81 (.150) 2,7 (.110) 8,311 8,306 (.3272) (.3270) 0,617 0,521 (.0243) (.0
33、205) 8,13 (.320) 6,86 (.27) 08 12,90 (.508) 2,74 (.108) 0,43 (.017) 6,58 (.259) 9,53 (.375) 4,83 (.190) 2,79 (.110) 4,83 (.190) 3,66 (.144) 10,973 10,968 (.4320) (.4318) 0,787 0,686 (.0310) (.0270) 9,40 (.370) 8,89 (.35) 10 16,13 (.635) 3,56 (.140) 0,51 (.020) 7,90 (.311) 11,13 (.438) 3,94 (.155) 3,
34、35 (.132) 5,88 (.231) 4,62 (.182) 13,846 13,840 (.5451) (.5449) 0,932 0,826 (.0367) (.0325) 8,89 (.350) 9,47 (.373) 12 19,38 (.763) 4,27 (.168) 0,58 (.023) 9,47 (.373) 12,70 (.500) 4,95 (.195) 4,01 (.158) 7,06 (.278) 5,69 (.224) 16,718 16,713 (.6582) (.6580) 1,087 0,965 (.0428) (.0380) 10,29 (.405)
35、11,38 (.448) Diameter code R S J1J2X E C1C2F G Hole limits min. max. max. 0,76 .030) Number of serrations 0,76 (.030) min. Ref. 0,05 (.002) 5 5 min. max. 05 0,25 (.010) 5,89 (.232) 20,32 (.800) 18 1,52 (.060) 0,13 (.005) 0,33 (.013) 0,81 (.032) 45 30 4,17 (.164) 4,24 (.167) 06 0,38 (.015) 7,42 (.292
36、) 21,08 (.830) 19 1,78 (.070) 0,13 (.005) 0,33 (.013) 0,81 (.032) 45 30 5,06 (.199) 5,13 (.202) 08 0,51 (.020) 9,17 (.361) 24,77 (.975) 20 2,29 (.090) 0,13 (.005) 0,33 (.013) 0,81 (.032) 45 30 6,60 (.260) 6,68 (.263) 10 0,64 (.025) 8,10 (.319) 31,60 (1.244) 18 1,98 (.078) 0,36 (.014) 0,51 (.022) 1,4
37、2 (.056) 45 30 7,93 (.312) 8,00 (.315) 12 0,76 (.030) 9,25 (.364) 41,35 (1.628) 18 1,85 (.073) 0,36 (.014) 0,58 (.023) 1,70 (0.67) 45 30 9,40 (.374) 9,58 (.377) aDiameter code 05 is also available with reduced diameter drive anvil / drive washer (7,92 0,13/.312 .005). See part number examples bThis
38、length of D may be 0,051 mm (.002) undersize. BS EN 6128:2017EN 6128:2017 (E) 9 Table 2 Static values Dimensions in kN (lbf) Diameter code Installed strength Single shear Tensile strength Tensile preload Spindle retention min. min. min. min. 05 8,811 (1980) 5,117 (1150) 0,512 (115) 2,558 (575) 06 13
39、,016 (2925) 7,520 (1690) 0,752 (169) 3,760 (845) 08 22,250 (5000) 12,905 (2900) 1,29 (290) 6,408 (1440) 10 32,040 (7200) 18,556 (4170) 1,856 (417) 9,256 (2080) 12 46,191 (10380) 26,566 (5970) 2,657 (597) 13,260 (2980) BS EN 6128:2017EN6128:2017(E)10Table3GriprangeDimensionsinmm(inch)Grip length code
40、UnderlapGriprangeOverlapDiametercode0506081012min.only05dia.min.06dia. to08dia.min.max.max.05dia. to08dia.LKLKLKLKLKRef.max.Ref.max.Ref.max.Ref.max.Ref.max.022,39a(.094)3,99(.0157)4,39(.173)8,53(.336)12,14(.478)9,02(.355)13,23(.521)033,71(.146)3,56b(.14)3,96(.156)5,59(.220)5,99(.236)10,11(.398)13,72
41、(.540)10,59(.417)14,81(.583)12,17(.479)16,38(.645)045,31(.209)5,16(.203)5,56(.219)7,16(.282)7,57(.298)11,71(.461)15,32(.603)12,19(.48)16,41(.646)13,74(.541)17,96(.707)12,85(.506)18,87(.743)13,92(.548)20,83(.82)056,88(.271)6,73(.265)7,14(.281)8,76(.345)9,17(.361)13,28(.523)16,89(.665)13,77(.542)17,98
42、(.708)15,34(.604)19,56(.77)14,43(.568)20,45(.805)15,49(.61)22,43(.883)068,48(.334)8,33(.328)8,74(.344)10,34(.407)10,74(.423)14,88(.586)18,49(.728)15,37(.605)19,58(.771)16,92(.666)21,13(.832)16,03(.631)22,05(.868)17,09(.673)24,00(.945)0710,06(.396)9,91(.390)10,31(.406)11,94(.470)12,34(.486)16,46(.648
43、)20,07(.790)16,94(.667)21,16(.833)18,52(.729)22,73(.895)17,60(.693)23,62(.930)18,67(.735)25,58(1.007)0811,66(.459)11,51(.453)11,91(.469)13,51(.532)13,92(.548)18,03(.710)21,64(.852)18,52(.729)22,73(.895)20,09(.791)24,31(.957)19,20(.756)25,22(.993)20,27(.798)27,18(1.07)0913,23(.521)13,08(.515)13,49(.5
44、31)15,11(.595)15,52(.611)19,61(.772)23,22(.914)20,09(.791)24,31(.957)21,69(.854)25,91(1.02)20,78(.818)26,80(1.055)21,84(.86)28,78(1.133)1014,83(.584)14.68(.578)15,09(.594)16,69(.657)17,09(.673)21,21(.835)24,82(.977)21,69(.854)25,91(1.020)23,27(.916)27,48(1.082)22,38(.881)28,40(1.118)23,44(.923)30,35
45、(1.195)1116,41(.646)16,26(.640)16,66(.656)18,29(.720)18,67(.735)22,81(.898)26,42(1.040)23,29(.917)27,51(1.083)24,87(.979)29,08(1.145)23,95(.943)29,97(1.180)25,02(.985)31,93(1.257)1218,01(.709)17,86(.703)18,26(.719)19,86(.782)20,27(.798)24,38(.960)27,99(1.102)24,87(.979)29,08(1.145)26,44(1.041)30,66(
46、1.207)25,55(1.006)31,57(1.243)26,62(1.048)33,53(1.32)1319,58(.771)19,43(.765)19,84(.781)21,46(.845)21,84(.860)25,98(1.023)29,59(1.165)26,47(1.042)30,68(1.208)28,04(1.104)32,26(1.270)27,13(1.068)33,15(1.305)28,19(1.11)35,13(1.383)1421,18(.834)21,03(.828)21,44(.844)23,04(.907)23,44(.923)27,56(1.085)31
47、,17(1.227)28,07(1.105)32,28(1.271)29,62(1.166)33,83(1.332)28,73(1.131)34,75(1.368)29,79(1.173)36,70(1.445)1522,76(.896)22,61(.890)23,01(.906)24,64(.970)25,02(.985)29,16(1.148)32,77(1.290)29,67(1.168)33,88(1.334)31,22(1.229)35,43(1,395.)30,30(1.193)36,32(1.430)31,37(1.235)38,28(1.507)1624,36(.959)24,
48、21(.953)24,61(.969)26,21(1.032)26,62(1.048)30,74(1.210)34,34(1.352)31,24(1.230)35,48(1.397)32,79(1.291)37,03(1.458)31,90(1.256)37,92(1.493)32,97(1.298)39,88(1.57)BS EN 6128:2017EN6128:2017(E)10Table3GriprangeDimensionsinmm(inch)Grip length codeUnderlapGriprangeOverlapDiametercode0506081012min.only05
49、dia.min.06dia. to08dia.min.max.max.05dia. to08dia.LKLKLKLKLKRef.max.Ref.max.Ref.max.Ref.max.Ref.max.022,39a(.094)3,99(.0157)4,39(.173)8,53(.336)12,14(.478)9,02(.355)13,23(.521)033,71(.146)3,56b(.14)3,96(.156)5,59(.220)5,99(.236)10,11(.398)13,72(.540)10,59(.417)14,81(.583)12,17(.479)16,38(.645)045,31(.209)5,16(.203)5,56(.219)7,16(.282)7,57(.298)11,71(.461)15,32(.603)12,19(.48)16,41(.646)13,74(.541)17,96(.707)12,85(.506)18,87(.743)13,92(.548)20,83(.82)056,88(.
