1、Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 16/07/2008 08:28, Uncontrolled Copy, (c) BSIg49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58a
2、nd tube Part 1: Technical conditions for inspection and deliveryICS 77.150.10Aluminium and aluminium alloys Cold drawn rod/bar BRITISH STANDARDBS EN 754-1:2008BS EN 754-1:2008Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 16/07/2008 08:28, Uncontrolled Copy, (c) BSIThis British Standard was
3、published under the authority of the Standards Policy and Strategy Committee on 30 April 2008 BSI 2008ISBN 978 0 580 55592 3Amendments/corrigenda issued since publicationDate Commentscontract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity
4、 from legal obligations.National forewordThis British Standard is the UK implementation of EN 754-1:2008. It supersedes BS EN 754-1:1997 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys.A list of organizations repre
5、sented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 754-1March 2008ICS 77.150.10 Supersedes EN 754-1:1997 English VersionAluminium and aluminium alloys -
6、Cold drawn rod/bar and tube -Part 1: Technical conditions for inspection and deliveryAluminium et alliages daluminium - Barres et tubes tirs -Partie 1: Conditions techniques de contrle et de livraisonAluminium und Aluminiumlegierungen - Gezogene Stangenund Rohre - Teil 1: Technische Lieferbedingunge
7、nThis European Standard was approved by CEN on 10 February 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical ref
8、erences concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member i
9、nto its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
10、 Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 200
11、8 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 754-1:2008: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 16/07/2008 08:28, Uncontrolled Copy, (c) BSIEN 754-1:2008 (E) 2 Contents Page Foreword3 1 Scope 5 2 Normative refer
12、ences 5 3 Terms and definitions .6 4 Ordering information.6 5 Requirements.8 5.1 Production and manufacturing processes .8 5.2 Quality control8 5.3 Chemical composition limits8 5.4 Mechanical properties.8 5.5 Freedom from surface defects .8 5.6 Tolerances on dimensions and form.8 5.7 Stress corrosio
13、n cracking resistance9 5.8 Additional requirements .9 6 Test procedures.9 6.1 Sampling.9 6.2 Test methods11 6.3 Re-tests.11 7 Inspection documents.12 8 Marking of products 12 9 Packaging .12 10 Arbitration.13 Annex A (normative) Location of test pieces 14 A.1 Round, square and hexagonal bar.14 A.2 R
14、ectangular bar15 A.3 Tube 15 Annex B (normative) Resistance to stress-corrosion cracking for alloy EN AW-7075 in tempers T73, T7351, T73510 and T73511 Electrical conductivity 17 Bibliography 18 BS EN 754-1:2008Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 16/07/2008 08:28, Uncontrolled Copy
15、, (c) BSIEN 754-1:2008 (E) 3 Foreword This document (EN 754-1:2008) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an id
16、entical text or by endorsement, at the latest by September 2008, and conflicting national standards shall be withdrawn at the latest by September 2008. This document supersedes EN 754-1:1997. Within its programme of work, Technical committee CEN/TC 132 entrusted CEN/TC 132/WG 5 “Extruded and drawn p
17、roducts“ to revise EN 754-1:1997. The following technical modifications have been introduced during the revision: Clause 1: Scope is clarified with respect to what is not included Clause 3: Definition of order document is included Clause 4: The order document shall contain information about applicat
18、ion especially for products to be anodised Subclauses 5.4 and 6.2.3: Provisions regarding Brinell hardness testing is included Subclauses 5.7 and 6.2.6: Requirements to stress corrosion cracking resistance is included (from former Annex A in Part 2) Subclause 6.1.1: For samples for chemical analysis
19、 reference is made to EN 14361 Subclause 6.1.3.3: For shapes and dimensions of test pieces reference is made to EN 10002-1 (and former Annex A is deleted) Clause 7: For inspection documents reference is made to EN 10204 Annex B: Resistance to stress corrosion cracking Electrical conductivity is adde
20、d (taken from former Part 2) EN 754 comprises the following parts under the general title “Aluminium and aluminium alloys Cold drawn rod/bar and tube “: Part 1: Technical conditions for inspection and delivery Part 2: Mechanical properties Part 3: Round bars, tolerances on dimensions and form Part 4
21、: Square bars, tolerances on dimensions and form Part 5: Rectangular bars, tolerances on dimensions and form Part 6: Hexagonal bars, tolerances on dimensions and form BS EN 754-1:2008Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 16/07/2008 08:28, Uncontrolled Copy, (c) BSIEN 754-1:2008 (E)
22、4 Part 7: Seamless tubes, tolerances on dimensions and form Part 8: Porthole tubes, tolerances on dimensions and form Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying
23、 any or all such patent rights. CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licenses on standardized standards products under reasonable and not discriminatory conditions then this product shall be removed from the corresponding standard. According to the CE
24、N/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
25、Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 754-1:2008Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 16/07/2008 08:28, Uncontrolled Copy, (c) BSIEN 754-1:2008 (E) 5 1 Scope This document speci
26、fies the technical conditions for inspection and delivery of aluminium and aluminium alloy cold drawn rod/bar and tube for general engineering applications. This document applies to products which are extruded and then cold drawn. This document does not apply to: forging stock (EN 603), products del
27、ivered in coils (EN 13958), coiled tubes cut to length (EN 13958). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references only the edition cited applies. For undated references the latest edition of the referenced docume
28、nt (including any amendments) applies. EN 515, Aluminium and aluminium alloys Wrought products Temper designations EN 573-3, Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products EN 754-2, Aluminium and aluminium alloys
29、 Cold drawn rod/bar and tube Part 2: Mechanical properties EN 754-3, Aluminium and aluminium alloys Cold drawn rod/bar and tube Part 3: Round bars, tolerances on dimensions and form EN 754-4, Aluminium and aluminium alloys Cold drawn rod/bar and tube Part 4: Square bars, tolerances on dimensions and
30、 form EN 754-5, Aluminium and aluminium alloys Cold drawn rod/bar and tube Part 5: Rectangular bars, tolerances on dimensions and form EN 754-6, Aluminium and aluminium alloys Cold drawn rod/bar and tube Part 6: Hexagonal bars, tolerances on dimensions and form EN 754-7, Aluminium and aluminium allo
31、ys Cold drawn rod/bar and tube Part 7: Seamless tubes, tolerances on dimensions and form EN 754-8, Aluminium and aluminium alloys Cold drawn rod/bar and tube Part 8: Porthole tubes, tolerances on dimensions and form EN 2004-1, Aerospace series Test methods for aluminium and aluminium alloy products
32、Part 1: Determination of electrical conductivity of wrought aluminium alloys EN 10002-1, Metallic materials Tensile testing Part 1: Method of test at ambient temperature EN 10204, Metallic products Types of inspection documents EN 12258-1:1998, Aluminium and aluminium alloys Terms and definitions Pa
33、rt 1: General terms EN 14242, Aluminium and aluminium alloys Chemical analysis Inductively coupled plasma optical emission spectral analysis BS EN 754-1:2008Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 16/07/2008 08:28, Uncontrolled Copy, (c) BSIEN 754-1:2008 (E) 6 EN 14361, Aluminium and
34、aluminium alloys Chemical analysis Sampling from metal melts EN ISO 6506-1, Metallic materials Brinell hardness test Part 1: Test method (ISO 6506-1:2005) ISO 9591, Corrosion of aluminium alloys Determination of resistance to stress corrosion cracking ASTM G47, Standard Test Method for Determining S
35、usceptibility to Stress-Corrosion Cracking of 2XXX and 7XXX Aluminium Alloy Products 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12258-1:1998 and the following apply. 3.1 order document document or set of documents agreed between supplier and purc
36、haser at the time of ordering 4 Ordering information The order document shall contain the following: a) form and type of product: form of the product (cold drawn rod/bar or tube). If tube, whether seamless or porthole/bridge, reference to EN 573-3 for chemical composition limits, reference to EN 515
37、 for temper designation, purchaser application, in particular whether subsequent anodising is intended. This shall be clearly stated on the order document; b) reference to EN 754-2 for mechanical property limits; c) a reference to this document (EN 754-1); d) dimensions and shape of the product: 1)
38、round tube: length, and only two of the following dimensions: outside diameter, inside diameter, wall thickness; 2) round bar: diameter, length; BS EN 754-1:2008Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 16/07/2008 08:28, Uncontrolled Copy, (c) BSIEN 754-1:2008 (E) 7 3) square and hexago
39、nal bar: width across flats, length; 4) rectangular bar: width, thickness, length; 5) all other cases: drawing of cross section, length; e) tolerances on dimensions and form, with reference to the appropriate European Standard and/or a drawing; f) quantity: mass, number of pieces, total length, tole
40、rance on quantity; g) any requirements for inspection documents; h) any special requirements agreed between supplier and purchaser: marking of products, reference to drawings, part numbers, etc, additional or special testing, e.g. stress corrosion testing, surface finish requirements, surface protec
41、tion, packaging, inspection prior to delivery, use of A50mmvalue instead of A value for elongation; i) for products intended to be anodised by the purchaser, the order document shall also contain the information about the intended particular surface treatment with reference to the relevant European
42、Standard. BS EN 754-1:2008Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 16/07/2008 08:28, Uncontrolled Copy, (c) BSIEN 754-1:2008 (E) 8 5 Requirements 5.1 Production and manufacturing processes Unless otherwise specified in the order document, the production and manufacturing processes shal
43、l be left to the discretion of the manufacturer. Unless it is explicitly stated in the order document, no obligation shall be placed on the manufacturer to use the same processes for subsequent or similar orders. 5.2 Quality control The supplier shall be responsible for the performance of all inspec
44、tion and tests required by the relevant European Standard and/or the particular specification prior to shipment of the product. If the purchaser wishes to inspect the product at the manufacturers works, he shall notify the supplier at the time of placing the order. 5.3 Chemical composition limits Th
45、e chemical composition limits shall be in conformity with the requirements specified in EN 573-3. If the purchaser requires closer limits for elements than those specified in the above standard, these limits shall be according to an agreement between supplier and purchaser and stated in the order do
46、cument. 5.4 Mechanical properties The mechanical properties shall be in conformity with those specified in EN 754-2 or those agreed between supplier and purchaser and stated in the order document. Typical Brinell hardness values are given in EN 754-2, but they are not binding for acceptance purposes
47、. However, a Brinell hardness value may be agreed upon for acceptance testing. 5.5 Freedom from surface defects The surface shall be free from defects prejudicial to its suitable and proper use. The product shall have a smooth and clean surface. However, small surface defects such as light scratches
48、, indentations, laminations, discolouration and non-uniform surface appearance resulting from heat-treatment, etc., which cannot always be totally avoided, are generally permitted on the product surface. Whilst an operation designed to mask a fault is not permitted, the elimination of a superficial
49、fault is permissible provided that the dimensional tolerances and material properties continue to meet the specification. For products intended for surface treatment, the superficial defects (discolouration, mechanical or structural) shall not be so extensive as to impair the decorative appearance of the surface after the agreed surface treatment. Limiting samples may be agreed between supplier and purchaser. 5
