1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 14315-1:2013Thermal insulating products for buildings In-situ formed sprayed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam productsPart 1: Specification for the
2、rigid foam spray system before installationBS EN 14315-1:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 14315-1:2013. The UK participation in its preparation was entrusted to T e c h n i c a l Committee PRI/72, Rigid cellular materials.A list of organizati
3、ons represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013.IS
4、BN 978 0 580 53441 6 ICS 91.100.60 Compliance with a British Standard cannot confer immunityfrom legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2013.Amendments issued since publicationDate T e x t a f f e c t e d
5、BS EN 14315-1:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14315-1 January 2013 ICS 91.100.60 English Version Thermal insulating products for buildings - In-situ formed sprayed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 1: Specification for the rigid foam sp
6、ray system before installation Produits isolants thermiques destins aux applications du btiment - Produits en mousse rigide de polyurthanne (PUR) ou de polyisocyanurate (PIR) projete, forms en place - Partie 1: Spcifications relatives aux systmes de projection de mousse rigide avant mise en oeuvre W
7、rmedmmstoffe fr das Bauwesen - An der Verwendungsstelle hergestellter Wrmedmmstoff aus Polyurethan (PUR) - und Polyisocyanurat (PIR)-Spritzschaum - Teil 1: Spezifikation fr das Schaumsystem vor dem Einbau This European Standard was approved by CEN on 17 November 2012. CEN members are bound to comply
8、 with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC M
9、anagement Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
10、 status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,
11、Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rig
12、hts of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14315-1:2013: EBS EN 14315-1:2013EN 14315-1:2013 (E) 2 Contents Page Foreword . 4 1 Scope 5 2 Normative references . 5 3 Terms, definitions, symbols and abbreviations 6 3.1 Terms and definitions
13、 6 3.2 Symbols and abbreviations . 8 4 Requirements . 9 4.1 General . 9 4.2 For all applications . 9 4.3 Specific applications 12 5 Test methods 15 5.1 Sampling and test specimen preparation . 15 5.2 Conditioning . 15 5.3 Testing 16 6 Designation code . 18 7 Evaluation of conformity 18 7.1 General .
14、 18 7.2 Initial type testing . 19 7.3 Factory production control 19 8 Marking, labelling and technical information 19 8.1 Marking and labelling . 19 8.2 Technical information 19 Annex A (normative) Determination of declared aged thermal conductivity and aged thermal resistance . 21 A.1 Introduction
15、21 A.2 Input data 21 A.3 Declared values 21 Annex B (normative) Initial type testing (ITT) and Factory production control (FPC) . 23 Annex C (normative) Determination of the aged values of thermal resistance and thermal conductivity 25 C.1 General . 25 C.2 Sampling and test specimen preparation . 25
16、 C.3 Determination of the initial value of thermal conductivity . 26 C.4 Determination of the accelerated aged value of thermal conductivity 27 C.5 Fixed increment procedure 29 C.6 Declaration of the aged values of thermal resistance and aged thermal conductivity . 31 Annex D (normative) Preparation
17、 of the test sample 33 D.1 Principle 33 D.2 Procedure . 33 Annex E (normative) Determination of the reaction profile and free-rise density 34 E.1 Introduction 34 E.2 Principle 34 E.3 Apparatus . 34 E.4 Procedure . 34 E.5 Free-rise density 35 Annex F (normative) Determination of substrate adhesion st
18、rength perpendicular to faces . 36 BS EN 14315-1:2013EN 14315-1:2013 (E) 3 F.1 Principle 36 F.2 Apparatus . 36 F.3 Sample preparation and conditioning . 36 F.4 Preparation of test specimens . 36 F.5 Testing procedure 36 F.6 Presentation of results . 36 Annex G (normative) Testing for reaction to fir
19、e products . 37 G.1 Scope 37 G.2 Product and installation parameters . 37 G.3 Mounting and fixing . 38 G.4 Field of application . 40 Annex H (normative) Testing for reaction to fire products in standardised assemblies simulating end-use application(s) 42 H.1 Scope 42 H.2 Product and installation par
20、ameters . 42 H.3 Mounting and fixing . 43 H.4 Field of application . 47 Annex I (informative) Example for the determination of the declared aged values of thermal conductivity and thermal resistance for a product . 49 Annex J (normative) Instructions for compiling thermal resistance performance char
21、ts . 51 J.1 Introduction 51 J.2 General . 51 J.3 Procedure for the manufacturer to create the performance charts . 53 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive . 57 Bibliography 64 BS EN 14315-1:2013EN 14315-1:2013 (E
22、) 4 Foreword This document (EN 14315-1:2013) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or
23、 by endorsement, at the latest by July 2013, and conflicting national standards shall be withdrawn at the latest by July 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for id
24、entifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is
25、an integral part of this document. This European Standard consists of two parts which form a package. The first part is the harmonised part satisfying the mandate and the CPD and is the basis for the CE marking covering the products, which are placed on the market. The second part, which is the non-
26、harmonised part, covers the specification for the installed products. Both parts need to be used for the application of the insulation products in the end-use applications covered by EN 14315. This European Standard is one of a series for mineral wool, expanded clay, expanded perlite, exfoliated ver
27、miculite, polyurethane/polyisocyanurate, cellulose, bound expanded polystyrene and expanded polystyrene in-situ formed insulation products used in buildings, but this standard may be used in other areas where appropriate. The reduction in energy used and emissions produced during the installed life
28、of insulation products exceeds by far the energy used and emissions made during the production and disposal processes. EN 14315, Thermal insulating products for buildings In-situ formed sprayed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products, consists of the following parts: Part 1
29、: Specification for the rigid foam spray system before installation (the present document) Part 2: Specification for the installed insulation products According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this Europe
30、an Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slove
31、nia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 14315-1:2013EN 14315-1:2013 (E) 5 1 Scope This European Standard specifies requirements for in-situ formed sprayed rigid polyurethane (PUR) and rigid polyisocyanurate (PIR) foam products when applied to walls, ceilings, roofs, sus
32、pended ceilings and floors. This Part 1 of this European Standard is a specification for the rigid foam spray system before installation. Part 1 of this European Standard describes the product characteristics and includes procedures for testing, marking and labelling and the rules for evaluation of
33、conformity. This European Standard does not specify the required levels of all properties to be achieved by a product to demonstrate fitness for purpose in a particular end-use application. The required levels are to be found in regulations or non-conflicting standards. This European Standard does n
34、ot cover factory made rigid polyurethane (PUR) or polyisocyanurate (PIR) foam insulation products or in-situ products intended to be used for the insulation of building equipment and industrial installations. NOTE Foam products are either called flexible or rigid. The flexible products are used in u
35、pholstery and mattresses and are characterised by their ability to deflect, support and recover to their original thickness continually during their in-use phase. Those that are not flexible are termed rigid and do not possess these flexible characteristics. They are mostly used for thermal insulati
36、on purposes and vary widely in their compression strength values. Once the cell structure is crushed in a rigid foam, it does not recover its thickness fully. Some of these rigid foams are very low in density with very low compression strengths and are sometimes described “commercially” as “soft foa
37、ms” or “semi-rigid” foams. This note has been included to clarify that all foams with such descriptions are covered by this standards used of the term rigid foam. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable fo
38、r its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 312, Particleboards Specifications EN 508-1, Roofing products from metal sheet Specification for self-supporting produ
39、cts of steel, aluminium or stainless steel sheet Part 1: Steel EN 520, Gypsum plasterboards Definitions, requirements and test methods EN 823, Thermal insulating products for building applications Determination of thickness EN 826, Thermal insulating products for building applications Determination
40、of compression behaviour EN 1602, Thermal insulating products for building applications Determination of the apparent density EN 1604, Thermal insulating products for building applications Determination of dimensional stability under specified temperature and humidity conditions EN 1605, Thermal ins
41、ulating products for building applications Determination of deformation under specified compressive load and temperature conditions EN 1606, Thermal insulating products for building applications Determination of compressive creep EN 1607:1996, Thermal insulating products for building applications De
42、termination of tensile strength perpendicular to faces EN 1609, Thermal insulating products for building applications Determination of short term water absorption by partial immersion BS EN 14315-1:2013EN 14315-1:2013 (E) 6 EN 12086, Thermal insulating products for building applications Determinatio
43、n of water vapour transmission properties EN 12667:2001, Thermal performance of building materials and products Determination of thermal resistance by means of guarded hot plate and heat flow meter methods Products of high and medium thermal resistance EN 12939, Thermal performance of building mater
44、ials and products Determination of thermal resistance by means of guarded hot plate and heat flow meter methods Thick products of high and medium thermal resistance EN 13172:2012, Thermal insulation products Evaluation of conformity EN 13238, Reaction to fire tests for building products Conditioning
45、 procedures and general rules for selection of substrates EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using test data from reaction to fire tests EN 13823:2010, Reaction to fire tests for building products Building products excluding flooring
46、s exposed to the thermal attack by a single burning item EN ISO 354, Acoustics Measurement of sound absorption in a reverberation room (ISO 354) EN ISO 1182, Reaction to fire tests for products Non-combustibility test (ISO 1182) EN ISO 1716, Reaction to fire tests for products Determination of the g
47、ross heat of combustion (calorific value) (ISO 1716) EN ISO 9229:2007, Thermal insulation Vocabulary (ISO 9229:2007) EN ISO 11654, Acoustics Sound absorbers for use in buildings Rating of sound absorption (ISO 11654) EN ISO 11925-2:2010, Reaction to fire tests Ignitability of products subjected to d
48、irect impingement of flame Single-flame source test (ISO 11925-2:2010) ISO 4590, Rigid cellular plastics Determination of the volume percentage of open cells and of closed cells 3 Terms, definitions, symbols and abbreviations For the purposes of this document, the terms and definitions given in EN I
49、SO 9229:2007 and the following apply. 3.1 Terms and definitions 3.1.1 polyurethane foam PUR (in-situ formed products) rigid cellular plastics insulation material or product with a structure based on polymers mainly of the polyurethane type 3.1.2 polyisocyanurate foam PIR (in-situ formed products) rigid cellular plastics insulation material or product with a structure based on polymers mainly of the polyisocyanurate type BS EN 14315-1:2013EN 14315-1:2013 (E) 7 3.1.3 polyurethane foam PU rigid cellular
