1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 15432-1:2011Winter and road service areamaintenance equipments Front-mounted equipmentsPart 1: Fixed front mounting platesBS EN 15432-1:2011 BRITISH STANDARDNational forewo
2、rdThis British Standard is the UK implementation of EN 15432-1:2011.Together with BS EN 15432-2, it supersedes BS EN 15432:2008 whichwill be withdrawn on publication of BS EN 15432-2.The UK participation in its preparation was entrusted to TechnicalCommittee B/513, Construction equipment and plant a
3、nd site safety.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 73051 1ICS 43.160Compliance
4、 with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 September 2011.Amendments issued since publicationDate Text affectedBS EN 15432-1:2011EUROPEAN STANDARD NORME EUROPENNE EU
5、ROPISCHE NORM EN 15432-1 July 2011 ICS 43.160 Supersedes EN 15432:2008English Version Winter and road service area maintenance equipments - Front-mounted equipments - Part 1: Fixed front mounting plates Matriels de viabilit hivernale et dentretien des dpendances routires - quipement frontal - Partie
6、 1: Plaques de base avant fixes Winterdienst- und Straenbetriebsdienstausstattung - Frontanbauausstattungen - Teil 1: Feste FrontanbauplattenThis European Standard was approved by CEN on 3 June 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the condit
7、ions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists
8、in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standa
9、rds bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and Un
10、ited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15432-1:20
11、11: EBS EN 15432-1:2011EN 15432-1:2011 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Interchangeability requirements 43.1 Front mounting plate .43.1.1 General provisions 43.1.2 Mounting plate classes .53.1.3 Strength requirements 53.1.4 Designation 63.1.5 Interchangeability dimens
12、ions .63.1.6 Tool fixing systems 103.2 Electrical and hydraulic connections . 113.2.1 Location on the vehicle 113.2.2 Clearance space 143.2.3 Connection types 153.2.4 Identification and preferred layout of hydraulic connections 153.3 Mechanical Power Take Off (PTO) 16Annex A (normative) Quick-coupli
13、ng VV95 system for front mounted equipments . 18A.1 General . 18A.2 Interchangeability requirements . 18A.2.1 Front mounting plate 18A.2.2 Electrical and hydraulic connections . 20A.2.3 Mechanical Power Take Off (PTO) 21Annex B (normative) Compact F1/C front mounting plate for combined road and off-
14、road applications . 22B.1 General . 22B.2 Interchangeability requirements . 22B.2.1 Front mounting plate 22BS EN 15432-1:2011EN 15432-1:2011 (E) 3 Foreword This document (EN 15432-1:2011) has been prepared by Technical Committee CEN/TC 337 “Winter maintenance and road service area maintenance equipm
15、ent”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2012 and conflicting national standards shall be withdrawn at the latest by January 2012. A
16、ttention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document together with EN 15432-2 supersedes EN 15432:2008. According to the CEN/C
17、ENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithu
18、ania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 15432-1:2011EN 15432-1:2011 (E) 4 1 Scope This European Standard specifies the requirements for the various elements of carrying vehicles to ensure in
19、terchangeability between a vehicle and different equipments that are to be mounted frontally. It specifies certain interchangeability dimensions of the front mounting plate, including its height above the ground, as well as the locations of coupling devices for electrical and hydraulic connections a
20、nd for mechanical power take off (PTO). This European Standard specifies three different classes of mounting plates in order to cover road vehicles, independently from vehicle category and maximum permissible load, of the greatest possible variety (commercial vehicles, multi-purpose vehicles, commun
21、al vehicles,) which are capable of carrying front-mounted equipments for winter maintenance and for road service area maintenance. This European Standard specifies, with regard to electrical and hydraulic connections and to PTO, only location areas, clearance spaces and preferred layout in order to
22、ensure interchangeability. Requirements applying to connectors, coupling devices and PTO splines are given in EN 15431. Normative Annex A specifies provisions for an advanced front coupling system that is able to allow for mounting and demounting equipments without the use of tools. Users having to
23、address specific needs (e.g. extreme weather conditions) may require the vehicle be fitted with such automatic coupling system. Normative Annex B gives provisions for a compact and light front mounting plate intended for combined road and off-road applications. 2 Normative references The following r
24、eferenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 15431, Winter and road service area maintenance equipments Po
25、wer system and related controls Interchangeability and performance requirements ISO 1176:1990, Road vehicles Masses Vocabulary and codes. 3 Interchangeability requirements 3.1 Front mounting plate 3.1.1 General provisions Mounting plates of all classes, as defined in following 3.1.2, shall be design
26、ed and installed to the carrying vehicle so as to allow for the easy and safe tilting of the cabin (if the vehicle has been designed to provide for this facility). Mounting plates of all classes, as defined in following 3.1.2, shall be designed and installed to the carrying vehicle so as to allow fo
27、r the mounting of a front towing hitch (if the vehicle has been designed to provide for this facility). Compliance to this requirement may be achieved in different ways, e.g. by a pivoting or folding mounting plate, by an appropriate un-obstructing design or by provisions for direct mounting of the
28、hitch to the mounting plate itself. Characteristics of the quick-coupling system designed to allow for mounting and demounting of equipments without the use of tools are given in Annex A. BS EN 15432-1:2011EN 15432-1:2011 (E) 5 Characteristics of the compact mounting plate designed for combined road
29、 and off-road applications are given in Annex B. 3.1.2 Mounting plate classes Table 1 gives indication on installation heights and on recommended range of the maximum design total mass (ISO 1176:1990, 4.7, ISO-M07) of the carrying vehicle for each of the three classes of mounting plates that are def
30、ined in this European Standard. Installation height is measured with the carrying vehicle being at kerb mass (ISO 1176:1990, 4.6, ISO-M06) from the ground to the upper edge of the mounting plate, as shown in Figures 2, 3 and 4. Table 1 Installation heights of mounting plate classes Mounting plate cl
31、ass Height Recommended range of carrying vehicle maximum design total mass amm t F 1 1000 60 7,5 F 2 870 50 3,5 and 9 F 3 650 30 6 aWhen mounting plates of classes F1 to F3 are being mounted on vehicles which are not covered by ISO 1176, recommended ranges as given in the table may not be applicable
32、. 3.1.3 Strength requirements Mounting plates shall be designed so as to withstand to the maximum loads and moments that are given in Table 2 for each appropriate class. The values given in Table 2 refer to static loads and moments applied by the greatest variety of equipments (e.g. snow plough, gra
33、ss cutting machine, ) that may be fixed on the mounting plate. Equipments apply static loads and moments when they are being held in a raised position for transportation and transfer purposes. Table 2 Maximum static loads Mounting plate class Vertical load, Fz kN Bending moment, My kNm Torsional mom
34、ent, Mx kNm F 1 22 22 45 F 2 12 12 18 F 3 5 5 5 Loads and moments given in Table 2 refer to the vehicle coordinate system as shown in Figure 1. Mounting plates shall also be able to withstand to foreseeable dynamic forces which may arise when working with equipments having maximum static loads shown
35、 in Table 2. BS EN 15432-1:2011EN 15432-1:2011 (E) 6 Figure 1 Vehicle coordinate system 3.1.4 Designation Mounting plates meeting the requirements of this European Standard shall be identified by the following information, in the order given: a) reference to this European Standard; b) indication of
36、the mounting plate class. EXAMPLE Mounting plate of class F 2: Mounting plate EN 15432-1:2011 F 2. 3.1.5 Interchangeability dimensions Interchangeability dimensions of mounting plates shall be according to: Figure 2 for Class F 1 mounting plates; Figure 3 for Class F 2 mounting plates; Figure 4 for
37、Class F 3 mounting plates. Dimensions not specified in Figures 2, 3 and 4 are left to the discretion of the manufacturer. BS EN 15432-1:2011EN 15432-1:2011 (E) 7 Dimensions in millimetres Option: Additional elements, which do not conflict with the characteristic dimensions, may be provided to couple
38、 infuse implements, using different fixing systems. NOTE Additional cut-outs are allowed if the stiffness is not reduced thereby. Figure 2 (continued) Key 1 Clearance for claws 2 Clearance for swivel bolt 3 Clearance for swivel bolt 4 Clearance 75 5 Cone 6 Clearance 130 7 Ground level Figure 2 Dimen
39、sions for F 1 mounting plates BS EN 15432-1:2011EN 15432-1:2011 (E) 8 Dimensions in millimetres NOTE Additional cut-outs are allowed if the stiffness is not reduced thereby. Figure 3 Dimensions for F 2 mounting plates BS EN 15432-1:2011EN 15432-1:2011 (E) 9 Dimensions in millimetres Figure 4 Dimensi
40、ons for F 3 mounting plates BS EN 15432-1:2011EN 15432-1:2011 (E) 10 3.1.6 Tool fixing systems 3.1.6.1 General In order to ensure interchangeability with already in-use tools, mounting plates defined in this European Standard are designed in such a way as to allow for different fixing systems. The c
41、hoice of the most appropriate fixing system shall be left to the tool manufacturer and to the user. The following subclauses give a description of all the fixing elements provided by each mounting plate class. Additional fixing elements which do not conflict with the characteristic dimensions given
42、in Figures 2, 3 and 4, i.e. which do not interfere with fixing elements listed in following 3.1.6.2, 3.1.6.3 and 3.1.6.4, may also be provided when there is a need of coupling in-use equipments having widespread fixing systems at national or regional level. 3.1.6.2 Class F 1 mounting plate Class F 1
43、 mounting plates provide for the following fixing elements: two pockets (centre to centre 630 mm 1 mm, section A-A in Figure 2) as a support for the relevant claws; two couples of lateral slots ( 30 mm + 1/-0 mm, centre to centre 910 mm + 0/-2 mm, section B-B in Figure 2) for the relevant swivelling
44、 bolts; a couple of upper slots ( 30 mm + 1/-0 mm, centre to centre 630 mm 1 mm, section C-C in Figure 2) for the relevant swivelling bolts; two threaded holes (M30, centre to centre 630 mm 1 mm, section D-D in Figure 2) for the relevant passing bolts; two holes ( 82 mm + 1/-0 mm, centre to centre 4
45、00 mm 1 mm, section E-E in Figure 2) for the relevant centring cones. When using swivelling bolts, the use of appropriate washers is strongly recommended. 3.1.6.3 Class F 2 mounting plate Class F 2 mounting plates provide for the following fixing elements: two pockets (centre to centre 630 mm 1 mm,
46、section A-A in Figure 3) as a support for the relevant claws; a couple of lateral slots ( 26 mm + 1/-0 mm, centre to centre 720 mm + 0/-2 mm, section B-B in Figure 3) for the relevant swivelling bolts; a couple of upper slots ( 26 mm + 1/-0 mm, centre to centre 630 mm 1 mm, section C-C in Figure 3)
47、for the relevant swivelling bolts; two holes ( 82 mm + 1/-0 mm, centre to centre 400 mm 1 mm, section D-D in Figure 3) for the relevant centring cones. When using swivelling bolts, the use of appropriate washers is strongly recommended. BS EN 15432-1:2011EN 15432-1:2011 (E) 11 3.1.6.4 Class F 3 moun
48、ting plate Class F 3 mounting plates provide for the following fixing elements: two pockets (centre to centre 300 mm 1 mm, section A-A in Figure 4) as a support for the relevant claws; a couple of lateral slots ( 20 mm + 1/-0 mm, centre to centre 400 mm + 0/-2 mm, section B-B in Figure 4) for the re
49、levant swivelling bolts; a couple of upper slots ( 20 mm + 1/-0 mm, centre to centre 300 mm 1 mm, section C-C in Figure 4) for the relevant swivelling bolts; two holes ( 42 mm + 0,5/-0 mm, centre to centre 260 mm 1 mm, section D-D in Figure 4) for the relevant centring cones. When using swivelling bolts, the use of appropriate washers is strongly recommended. 3.2 Electrical and hydraulic connections Electrical connectors and
