1、BS EN 15719:2009ICS 91.140.70NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDSanitary appliances Baths made fromimpact modifiedcoextruded ABS/acrylicsheets Requirementsand test methodsCopyright European Committee for Standardization Provided by IHS under license
2、 with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 January2010 BSI 2010ISBN 978 0 580 57929 5Amendments/corrigenda issued since publicationDate CommentsBS
3、 EN 15719:2009National forewordThis British Standard is the UK implementation of EN 15719:2009.The UK participation in its preparation was entrusted to TechnicalCommittee B/503, Sanitary appliances.A list of organizations represented on this committee can be obtained onrequest to its secretary.This
4、publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Copyright European Committee for Standardization Provided by IHS under license with CEN
5、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 15719:2009EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15719 December 2009 ICS 91.140.70 English Version Sanitary appliances - Baths made from impact modified coextruded ABS/acrylic sheets - Requirements
6、 and test methodsAppareils sanitaires - Baignoires en feuilles coextrudes ABS/acrylique modifi choc - Prescriptions et mthodes dessai Sanitrausstattungsgegenstnde - Badewannen, hergestellt aus schlagzh-modifizierten coextrudierten ABS/Acrylplatten - Anforderungen und Prfverfahren This European Stand
7、ard was approved by CEN on 7 November 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning
8、such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own lang
9、uage and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, L
10、uxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All
11、rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15719:2009: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 15
12、719:2009EN 15719:2009 (E) 2 Contents Page Foreword 41 Scope 52 Normative references 53 Terms and definitions .54 Requirements .54.1 General 54.2 Material .54.3 Surface appearance .54.4 Waste outlet hole .64.5 Overflow hole .64.6 Hole edges 64.7 Bath-mounted tapware 64.8 Handgrips .64.9 Dimensional d
13、eviations .64.10 Geometric deviations 64.10.1 General 64.10.2 Squaring .64.10.3 Straightness of the rim sides .64.10.4 Straightness of the bottom edge of the rim 74.10.5 Flatness of the top surface of the rim74.11 Bottom of the bath .74.12 Resistance to temperature changes 74.13 Resistance to impact
14、 .74.14 Permitted deflections 74.15 Bath rims 84.16 Surface mechanical resistance 84.17 Chemical and stain resistance .85 Marking .8Annex A (normative) Bath test methods.9A.1 Sequence of tests 9A.2 Geometric deviations 9A.2.1 Test apparatus .9A.2.2 Squaring .9A.2.3 Straightness of the rim side 10A.2
15、.4 Straightness of the bottom edge of the rim . 11A.2.5 Flatness of the top surface of the rim. 12A.3 Resistance to temperature change . 13A.3.1 Test apparatus 13A.3.2 Procedure 13A.4 Resistance to impact 14A.4.1 Test apparatus 14A.4.2 Test procedure 15A.5 Determination of deflections . 15A.5.1 Gene
16、ral . 15A.5.2 Test apparatus 15A.5.3 Installation methods . 16A.5.4 Preloading . 18A.5.5 Deflection test 1 Deflection of the rim and the bottom due to a load on the bottom . 18A.5.6 Deflection test 2 Deflection of the bottom and rim due to a load on the bottom 19Copyright European Committee for Stan
17、dardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 15719:2009EN 15719:2009 (E) 3 A.5.7 Deflection test 3 Deflection of the rim due to a load on the long side of the rim 21A.5.8 Deflection test 4 Deflection of the
18、 rim due to a load on the end of the bath 22A.6 Handgrip tests . 23A.6.1 General . 23A.6.2 Test apparatus . 23A.6.3 Procedure . 23A.7 Resistance to scratching 23A.7.1 Test apparatus . 23A.7.2 Test specimen 24A.7.3 Procedure . 24Bibliography 26Copyright European Committee for Standardization Provided
19、 by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 15719:2009EN 15719:2009 (E) 4 Foreword This document (EN 15719:2009) has been prepared by Technical Committee CEN/TC 163 “Sanitary appliances”, the secretariat of which is held by U
20、NI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2010, and conflicting national standards shall be withdrawn at the latest by June 2010. Attention is drawn to the possibility that some of
21、the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. Attention is drawn to EN 14516 1, which has been prepared under Mandate M/110 “Sanitary Appliances“ which was given to CEN by the Europea
22、n Commission and the European Free Trade Association and supports the Essential Requirements to allow CE marking under the Construction Products Directive (89/106/EEC). According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to imp
23、lement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerlan
24、d and the United Kingdom. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 15719:2009EN 15719:2009 (E) 5 1 Scope This European Standard specifies requirements for baths for
25、domestic purposes made from impact modified coextruded ABS/acrylic sheets conforming to EN 13559 with the aim of ensuring that the product, when installed in accordance with the manufacturers instructions, will provide satisfactory performance in use. This European Standard is applicable to all size
26、s and shapes of baths. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN
27、13559:2003, Specifications for impact modified coextruded ABS/Acrylic sheets for baths and shower trays for domestic purposes ISO 4586-2:2004, High-pressure decorative laminates Sheets made from thermosetting resins Part 2: Determination of properties 3 Terms and definitions For the purposes of this
28、 document, the following terms and definitions apply. 3.1 domestic purposes use in homes, hotels, accommodation for students, hospitals and similar buildings, except when special medical provisions are required 4 Requirements 4.1 General The manufacturer shall provide instructions for installation a
29、nd care with each bath. The bath shall be free from sharp edges that would be exposed after the installation of the bath in accordance with the manufacturers instructions. 4.2 Material The bath shall be manufactured from impact modified coextruded ABS/acrylic sheet material complying with EN 13559.
30、4.3 Surface appearance When the bath is visually inspected under strong and oblique illumination there shall be no evidence of cracks, chips, or other surface defects, such as unexpected changes in colours, etc. that will impair the appearance or performance of the bath. Copyright European Committee
31、 for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 15719:2009EN 15719:2009 (E) 6 4.4 Waste outlet hole The bath shall have at least one outlet hole. The dimensions of the waste outlet hole and the cleara
32、nce around the waste outlet hole shall either be in accordance with the requirements of EN 232 or the manufacturer shall supply or recommend a suitable waste outlet fitting. 4.5 Overflow hole When the bath is provided with an overflow hole the dimensions of the overflow hole and the clearance around
33、 the overflow hole shall either be in accordance with the requirements of EN 232 or the manufacturer shall supply or recommend a suitable overflow fitting. 4.6 Hole edges The edges of any holes in the bath shall not show evidence of chips, cracks, or any other defects that may impair the appearance
34、or performance of the bath. 4.7 Bath-mounted tapware When the bath is intended to accommodate bath-mounted tapware the space and area provided shall either comply with the requirements of EN 232 or the manufacturer shall supply or recommend a suitable tapware. 4.8 Handgrips When a handgrip(s) is fit
35、ted it shall be tested in accordance with A.6 and the bath and the handgrip shall be free from any permanent deformation or other defects that will impair the functioning and/or the appearance of the bath. If not pre-fitted by the manufacturer, the manufacturers instructions shall indicate how and w
36、here the handgrips are fitted. 4.9 Dimensional deviations The dimensions of baths shall not deviate from the size quoted by the manufacturer by greater than 5 mm. If the manufacturer states two sizes (e.g. both a work size and a nominal size) he shall state to which size the permitted deviations app
37、ly. For round baths, length and width correspond to the diameter. 4.10 Geometric deviations 4.10.1 General The straight sides or edges of the bath that might abut independent surroundings or supporting structures shall comply with the requirements of 4.10.2 to 4.10.4 and all baths shall comply with
38、4.10.5. These requirements are not applicable to sides or edges that are purposely designed as curves or slopes. 4.10.2 Squaring When tested in accordance with A.2.2 the deviation from square, q, shall be less than or equal to 5 mm. 4.10.3 Straightness of the rim sides When tested in accordance with
39、 A.2.3 the deviation from straightness of the rim sides, s, shall be less than or equal to 5 mm. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 15719:2009EN 15719:2009 (E)
40、 7 4.10.4 Straightness of the bottom edge of the rim When tested in accordance with A.2.4 the deviation from straightness of the bottom edge of the rim, r, shall be less than or equal to 5 mm. 4.10.5 Flatness of the top surface of the rim When tested in accordance with A.2.5 the deviation from flatn
41、ess of the top surface of the rim, c, shall be less than or equal to 5 mm. 4.11 Bottom of the bath When the bath is installed in accordance with the manufacturers instructions and the waste outlet hole is open, all water shall empty from the bath unless prevented by surface tension. 4.12 Resistance
42、to temperature changes When tested in accordance with A.3 baths shall show no evidence of distortion or other defects that impair the appearance or functioning of the bath and any deflection shall be less than or equal to 4 mm. 4.13 Resistance to impact When tested in accordance with A.4 the bottom
43、and the rim of the bath shall show no evidence of distortion or other defects that impair the appearance or functioning of the bath. 4.14 Permitted deflections When tested in accordance with A.5 the deflections shall be less than or equal to the values given in Table 1. Table 1 Permitted deflections
44、 Test method Maximum deflections aunder load and permitted residual deflections for installation methods bmm a)b)c) d) e) A.5.5 1 on the four free rims 2 on the bottom 1 on the three free rims 0,5 on the fixed rim 2 on the bottom 1 on the two free rims 0,5 on the two fixed rims 2 on the bottom 1 on
45、the free rim 0,5 on the three fixed rims 2 on the bottom 0,5 on all rims 2 on the bottom A.5.6 2 on the four free rims 3 on the bottom 2 on the three free rims 0,5 on the fixed rim 3 on the bottom 2 on the two free rims 0,5 on the two fixed rims 3 on the bottom 2 on the free rim 0,5 on the three fix
46、ed rims 3 on the bottom 0,5 on all rims 3 on the bottom A.5.7 4 on the rim 0,3 residual 4 on the rim 0,3 residual 4 on the rim 0,3 residual 4 on the rim 0,3 residual Not applicable A.5.8 4 on the rim 0,3 residual 4 on the rim 0,3 residual 4 on the rim 0,3 residual Not applicable Not applicable aValu
47、es in addition to any deflection of the test rig (see A.5.2). bSee A.5.3. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 15719:2009EN 15719:2009 (E) 8 4.15 Bath rims When
48、a bath incorporating a nominally flat top surface of the rim is installed in accordance with the manufacturers instructions, the rim shall not encourage water to drain away from the inside of the bath. Roll top rims and rims incorporating special features, e.g. headrests, are not subject to this requirement. 4.16 Surface mechanical resistance When tested in accordance with A.7, any scratc
