1、BSI Standards PublicationBS EN 16287-1:2014Glass packaging Screw finishes for pressure capsulesPart 1: Returnable glass MCA 1 finishBS EN 16287-1:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 16287-1:2014. The UK participation in its preparation was entru
2、sted to TechnicalCommittee PKW/0/-/7, Packaging - Glass.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The Br
3、itish Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 82974 1 ICS 55.100 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May
4、2014.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 16287-1:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16287-1 March 2014 ICS 55.100 English Version Glass packaging - Screw finishes for pressure capsules - Part 1: Returnable glass MCA 1 finish Emballage en verre -
5、 Bagues vis pour capsules pression - Partie 1: Bague MCA 1 pour verre consign Verpackungen aus Glas - Schraubmundstcke fr Flaschen mit Innendruck - Teil 1: Mehrweg-MCA 1-(Glas-)MundstckThis European Standard was approved by CEN on 12 January 2014. CEN members are bound to comply with the CEN/CENELEC
6、 Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or t
7、o any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the offici
8、al versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, N
9、orway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of ex
10、ploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16287-1:2014 EBS EN 16287-1:2014EN 16287-1:2014 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 4 2 Terms and definitions .4 3 Dimensions .4 Bibliography 9 BS EN 16287-1:2014EN 16287-1:2014 (E) 3
11、Foreword This document (EN 16287-1:2014) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by
12、 September 2014 and conflicting national standards shall be withdrawn at the latest by September 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all suc
13、h patent rights. EN 16287, Glass packaging Screw finishes for pressure capsules, consists of the following parts: Part 1: Returnable glass MCA 1 finish Part 2: One way glass MCA 1 finish According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countrie
14、s are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland
15、, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 16287-1:2014EN 16287-1:2014 (E) 4 Introduction This European Standard is based on CE.T.I.E. (International Technical Centre for Bottling and related Packaging) data sheet GME 32.05.1 Efficient p
16、ackaging is of great importance for the distribution and the protection of goods. Insufficient or inappropriate packaging can lead to damage or wastage of the contents of the pack. 1 Scope This European Standard specifies the dimensions of the 28 mm screw finish for glass containers designated MCA 1
17、 for returnable glass. 2 Terms and definitions For the purposes of this document, the following term and definition applies. 2.1 MCA (glass) finish designed for the closure of pressurized or vacuum liquids with a tamper-evident closure (metal or plastic) 3 Dimensions The design and dimensions of the
18、 finish shall be as shown in Table 1 and Figure 1, Figure 2, Figure 3, Figure 4 and Figure 5. Table 1 Design and dimensions of the finish Pitch TPI cutter 3,175 mm 2 12 8 12,5 mm = Helix angle or angle or fixture to cutter. NOTE TPI = Threads per Inch. One inch is equal to 25,4 mm. The Tan of helix
19、angle for cutter is calculated via the following formula: ( )2nominalnominalpitchTanET += where T is the thread diameter; E is the wall diameter of threaded finish. The average of the maximum and minimum of L diameter is as close as possible to L nominal. The mean diameter 2mindiametermaxdiameter +L
20、 is in the tolerance of 0,2 mm. Optional: depressed thread at mould parting line (see EN 16292). BS EN 16287-1:2014EN 16287-1:2014 (E) 5 Dimensions in millimetres Key N Neck (under bead) diameter H Thread height S Start of thread position from sealing surface to intersection of thread flank F Height
21、 of the finish L Locking bead diameter T Thread diameter E Wall diameter of threaded finish NOTE Bore diameter (17,0 0,5) mm for a depth of 3 mm Figure 1 MCA 1 finish BS EN 16287-1:2014EN 16287-1:2014 (E) 6 Dimensions in millimetres Type 1 Type 2 Key a Mould parting line b Sealing surface Figure 2 P
22、ossible alternative constructions of the bore entrance to suit glass manufacturer The sealing surface is smooth and free of any defects and flash. BS EN 16287-1:2014EN 16287-1:2014 (E) 7 Dimensions in millimetres Minimum through bore 16,0 Figure 3 Detail of the profile NOTE Z-Z is the last full dept
23、h and width of thread. Beyond this point and Y-Y, the thread root is gradually increased to full thread diameter T in 90. Figure 4 Run out of thread BS EN 16287-1:2014EN 16287-1:2014 (E) 8 Dimensions in millimetres Figure 5 Limit of construction BS EN 16287-1:2014EN 16287-1:2014 (E) 9 Bibliography 1
24、 CE. T.I.E. data sheet GME 32.05 - MCA 1 finish 1)2 EN 16292, Glass packaging - Screw finishes - Depressed threads 1) Obtainable through Centre Technique International de lEmbouteillage et du conditionnement (CE.T.I.E), 112- 114, rue La Botie, 7500Paris, France www.cetie.org, TP: 0033-1-42 65 26 45,
25、 TF: 0033-1-40 07 03 21. This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standar
26、dization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into st
27、andards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can p
28、rovide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopt
29、ed European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription
30、services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is ref
31、reshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscrib
32、ing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications o
33、n your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We co
34、ntinually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and oth
35、er BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the
36、Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing
37、Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
