1、BRITISH STANDARDBS EN 60512-15-7:2008Connectors for electronic equipment Tests and measurements Part 15-7: Connector tests (mechanical) Test 15g: Robustness of protective cover attachment ICS 31.220.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g4
2、0g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 60512-15-7:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2008 BSI 2008ISBN 978 0 580 55905 1National forewordThis Br
3、itish Standard is the UK implementation of EN 60512-15-7:2008. It is identical to IEC 60512-15-7:2008.The UK participation in its preparation was entrusted to Technical Committee EPL/48, Electromechanical components and mechanical structures for electronic equipment.A list of organizations represent
4、ed on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corr
5、igenda issued since publicationDate CommentsEUROPEAN STANDARD EN 60512-15-7 NORME EUROPENNE EUROPISCHE NORM July 2008 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat:
6、rue de Stassart 35, B - 1050 Brussels 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-15-7:2008 E ICS 31.220.10 English version Connectors for electronic equipment - Tests and measurements - Part 15-7: Connector tests (
7、mechanical) - Test 15g: Robustness of protective cover attachment (IEC 60512-15-7:2008) Connecteurs pour quipements lectroniques - Essais et mesures - Partie 15-7: Essais (mcaniques) des connecteurs - Essai 15g: Robustesse de la fixation du capot de protection (CEI 60512-15-7:2008) Steckverbinder fr
8、 elektronische Einrichtungen - Mess- und Prfverfahren - Teil 15-7: Mechanische Prfungen an Steckverbindern - Prfung 15g: Widerstandsfhigkeit der Schutzkappe mit Befestigung (IEC 60512-15-7:2008) This European Standard was approved by CENELEC on 2008-07-01. CENELEC members are bound to comply with th
9、e CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat o
10、r to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the offic
11、ial versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal,
12、 Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Foreword The text of document 48B/1849/FDIS, future edition 1 of IEC 60512-15-7, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitt
13、ed to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-15-7 on 2008-07-01. This standard is to be read in conjunction with EN 60512-1 and EN 60512-1-100 which explains the structure of the EN 60512 series. The following dates were fixed: latest date by which the EN has to be imp
14、lemented at national level by publication of an identical national standard or by endorsement (dop) 2009-04-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2011-07-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the Internatio
15、nal Standard IEC 60512-15-7:2008 was approved by CENELEC as a European Standard without any modification. _ BS EN 60512-15-7:2008 2 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 15-7: Connector tests (mechanical) Test 15g: Robustness of protective cover attachment 1 Scope and objec
16、t This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this document is to detail a standard test method to assess
17、the ability of a connector cover and its attachment to withstand mechanical stresses. NOTE Such a cover may be protective in any sense. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited appli
18、es. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60512-1-1, Connectors for electronic equipment Tests and measurements Part 1-1: General examination Test 1a: Visual examination 3 Preparations 3.1 Preparation of specimen The specimen sh
19、all consist of a cover fixed to its connector or a specified test fixture. Any preconditioning given in the detail specification shall be applied. 3.2 Equipment For the application of the loads, a suitable device able to provide the controls on the loads (intensity, rate of increase, time of constan
20、t load application) shall be required (e.g.: a universal materials testing machine). NOTE If the detail specification requires special preconditioning of the specimen, all the necessary equipment detailed in the relevant documents describing such conditioning would also be required. 3.3 Mounting If
21、mounting of the specimen is appropriate, it shall be as specified in the detail specification. 4 Test method Unless otherwise stated in the detail specification, 3 connectors shall be tested. BS EN 60512-15-7:2008 3 4.1 Procedure The specified force shall be applied in the direction of the normal re
22、moval direction of the cover. In the case of screwed caps, this shall not include an unscrewing torque. The specified force shall then be applied perpendicular to the normal removal axis of the cover. This shall be done in four directions in the same plane, mutually at right angles to each other. In
23、 the case of screwed caps only, one such force shall be applied. In some designs there may be a disadvantageous or worst case direction for the application of this force. If so at least one of the four directions shall be in this direction. The load shall be applied at a rate of 25 mm/min. The maxim
24、um load shall be applied for 5 minutes. The force shall then be removed. 4.2 Measurements 4.2.1 Before testing Visual examination according to IEC 60512-1-1 shall be done. 4.2.2 During testing No malfunction of the cover or its attachment system shall occur. 4.2.3 After testing Visual examination ac
25、cording to IEC 60512-1-1 shall be done. Special attention shall be given to the operation of sealing, coupling and retaining devices. 5 Details to be specified When this test is required by a detail specification the following shall be given therein, a) number of connectors to be tested (if other th
26、an 3); b) preconditioning required; c) loads to be applied, point of application may be specified; d) details of test fixture, if corresponding connector is not to be used; e) if any displacement is permitted; f) any deviation from the standard test method. _ BS EN 60512-15-7:2008 4 Annex ZA (normat
27、ive) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the re
28、ferenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60512-1-1 -1)Connectors for electronic equipment - Tests and measurements - Pa
29、rt 1-1: General examination - Test 1a: Visual examination EN 60512-1-1 20022)1)Undated reference. 2)Valid edition at date of issue. BS EN 60512-15-7:2008 5 BS EN 60512-15-7:2008BSI Group Headquarters389 Chiswick High Road,London W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards Institut
30、ion (BSI)BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards sh
31、ould make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical commit
32、tee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders f
33、or all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ response to orders for international standards,
34、it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Export
35、ers Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and rec
36、eive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be found at htt
37、p:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no
38、extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070 Email:
