EN 60512-17-2-2011 en Connectors for electronic equipment - Tests and measurements - Part 17-2 Cable clamping tests - Test 17b Cable clamp resistance to cable rotation《电子设备连接器 试验和测.pdf

上传人:testyield361 文档编号:718271 上传时间:2019-01-04 格式:PDF 页数:10 大小:1MB
下载 相关 举报
EN 60512-17-2-2011 en Connectors for electronic equipment - Tests and measurements - Part 17-2 Cable clamping tests - Test 17b Cable clamp resistance to cable rotation《电子设备连接器 试验和测.pdf_第1页
第1页 / 共10页
EN 60512-17-2-2011 en Connectors for electronic equipment - Tests and measurements - Part 17-2 Cable clamping tests - Test 17b Cable clamp resistance to cable rotation《电子设备连接器 试验和测.pdf_第2页
第2页 / 共10页
EN 60512-17-2-2011 en Connectors for electronic equipment - Tests and measurements - Part 17-2 Cable clamping tests - Test 17b Cable clamp resistance to cable rotation《电子设备连接器 试验和测.pdf_第3页
第3页 / 共10页
EN 60512-17-2-2011 en Connectors for electronic equipment - Tests and measurements - Part 17-2 Cable clamping tests - Test 17b Cable clamp resistance to cable rotation《电子设备连接器 试验和测.pdf_第4页
第4页 / 共10页
EN 60512-17-2-2011 en Connectors for electronic equipment - Tests and measurements - Part 17-2 Cable clamping tests - Test 17b Cable clamp resistance to cable rotation《电子设备连接器 试验和测.pdf_第5页
第5页 / 共10页
点击查看更多>>
资源描述

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationConnectors for electronic equipment Tests and measurementsPart 17-2: Cable clamping tests Test 17b: Cable clamp resistance to cable rotationBS EN 60512-17-2:2011National foreword

2、This British Standard is the UK implementation of EN 60512-17-2:2011. It isidentical to IEC 60512-17-2:2011. It supersedes Test 17b from BS 5772-9:1993, IEC 60512-9:1992 which will remain current until all the tests it contains have been revised.The UK participation in its preparation was entrusted

3、to Technical CommitteeEPL/48, Electromechanical components and mechanical structures for electronic equipment.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users

4、 are responsible for its correct application. BSI 2011ISBN 978 0 580 62162 8ICS 31.220.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 31 July 2011.Amendments is

5、sued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60512-17-2:2011EUROPEAN STANDARD EN 60512-17-2 NORME EUROPENNE EUROPISCHE NORM June 2011 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elekt

6、rotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-17-2:2011 E ICS 31.220.01 English version Connectors for electronic equipment - Tests and measu

7、rements - Part 17-2: Cable clamping tests - Test 17b: Cable clamp resistance to cable rotation (IEC 60512-17-2:2011) Connecteurs pour quipements lectroniques Essais et mesures Partie 17-2: Essais de pincement de cble Essai 17b: Rsistance des pinces de maintien des cbles la rotation des cbles (CEI 60

8、512-17-2:2011) Steckverbinder fr elektronische Einrichtungen - Mess- und Prfverfahren - Teil 17-2: Prfungen der Kabelabfangung - Prfung 17b: Kabelabfangung, Sicherheit gegen Einschneiden des Kabelmantels (IEC 60512-17-2:2011) This European Standard was approved by CENELEC on 2011-05-12. CENELEC memb

9、ers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applicati

10、on to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat h

11、as the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, th

12、e Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 60512-17-2:2011EN 60512-17-2:2011 - 2 - Foreword The text of document 48B/2124/CDV, future edition 1 of IEC 60512-17-2, prepared by SC 48B, Connectors, of IEC TC 48, Electro

13、mechanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-17-2 on 2011-05-12. This standard is to be read in conjunction with EN 60512-1 and EN 60512-1-100, which explains the structure of the EN 6

14、0512 series. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest date by which the EN has to be implem

15、ented at national level by publication of an identical national standard or by endorsement (dop) 2012-02-12 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2014-05-12 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International

16、 Standard IEC 60512-17-2:2011 was approved by CENELEC as a European Standard without any modification. _ BS EN 60512-17-2:2011- 3 - EN 60512-17-2:2011 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced docum

17、ents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modification

18、s, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60512-1 - Connectors for electronic equipment - Tests and measurements - Part 1: General EN 60512-1 - IEC 60512-1-1 - Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination

19、- Test 1a: Visual examination EN 60512-1-1 - IEC 60512-1-100 - Connectors for electronic equipment - Tests and measurements - Part 1-100: General - Applicable publications EN 60512-1-100 - BS EN 60512-17-2:2011 2 60512-17-2 IEC:2011 CONTENTS Scope and object 5 1Normative references . 5 2Preparation

20、of the specimen . 5 3Test method . 5 4Final measurements . 6 5Requirements . 6 6Details to be specified 6 7Figure 1 Cable test set-up 6 BS EN 60512-17-2:201160512-17-2 IEC:2011 5 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 17-2: Cable clamping tests Test 17b: Cable clamp resistan

21、ce to cable rotation Scope and object 1This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to det

22、ail a standard method to assess the ability of a cable-clamping device to allow rotary movement of the cable/wire bundle without damage to the external surface of the cable/wire bundle, the cable-clamping device, the connector or the sub-assembly. Normative references 2The following referenced docum

23、ents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60512-1, Connectors for electronic equipment Tests and measurements Part 1:

24、 General IEC 60512-1-1, Connectors for electronic equipment Tests and measurements Part 1-1: General examination Test 1a: Visual examination IEC 60512-1-100, Connectors for electronic equipment Tests and measurements Part 1-100: General Applicable publications Preparation of the specimen 3The specim

25、en shall consist of the specified cable/wire bundle fitted in the normal manner to its associated component or sub-assembly by means of the cable-clamping device. The specimen shall be prepared and mounted in accordance with the detail specification. Test method 4The free end of the cable/wire bundl

26、e shall be deflected at an angle of 45 to 50 to the axis at the point of entry to the specimen and rotated 360, see Figure 1. The number and the speed of the rotations shall be stated in the detail specification. BS EN 60512-17-2:2011 6 60512-17-2 IEC:2011 Connector Platen Mass Bushing hole 45-50 IE

27、C 693/11 Figure 1 Cable test set-up During the test, the cable/wire bundle shall be subjected to a torque or a pull not greater than the minimum value necessary to maintain the proper alignment of the cable/wire bundle. NOTE If necessary, suitable devices to measure and control the forces and torque

28、s (e.g. a universal materials testing machine and torque tester) should be used. Final measurements 5The specimen shall be examined visually in accordance with IEC 60512-1-1, Test 1a at the junction of the cable/wire bundle and the clamping device and at the junction of the clamping device and the c

29、omponent or sub-assembly. Requirements 6There shall be no damage to the cable/wire bundle external surface, nor to the specimen. Details to be specified 7When this test is required by the detail specification, the following details shall be specified: a) preparation of the specimen and type of cable

30、/wire bundle to be used; b) mounting of the specimen; c) number and speed of rotations; d) requirements for final measurements; e) any deviation from the standard test method. _ BS EN 60512-17-2:2011This page deliberately left blankBSI is the independent national body responsible for preparing Briti

31、sh Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Roa

32、d London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would b

33、e grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual u

34、pdating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website a

35、ddition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been pu

36、blishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services a

37、re also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other ben

38、efits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications

39、. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocop

40、ying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email:

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1