1、BSI Standards PublicationConnectors for electronic equipment Product requirementsPart 2-109: Circular connectors Detail specification for connectors with M 12 1 screw-locking, for data transmission frequencies up to 500 MHzBS EN 61076-2-109:2014National forewordThis British Standard is the UK implem
2、entation of EN 61076-2-109:2014.It is identical to IEC 61076-2-109:2014. It supersedesDD IEC/PAS 61076-2-109:2010 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee EPL/48, Electromechanical components and mechanical structures for electronic equipment.A l
3、ist of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards L
4、imited 2014ISBN 978 0 580 71532 7ICS 31.220.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 September 2014.Amendments/corrigenda issued since publicationDate
5、Text affectedBRITISH STANDARDBS EN 61076-2-109:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61076-2-109 August 2014 ICS 31.220.10 English Version Connectors for electronic equipment - Product requirements - Part 2-109: Circular connectors - Detail specification for connectors with M 12 1
6、 screw-locking, for data transmission frequencies up to 500 MHz (IEC 61076-2-109:2014) Connecteurs pour quipements lectroniques - Exigences de produit - Partie 2-109: Connecteurs circulaires - Spcification particulire relative aux connecteurs avec verrouillage vis M 12 1, pour les transmissions de d
7、onnes des frquences jusqu 500 MHz (CEI 61076-2-109:2014) Steckverbinder fr elektronische Einrichtungen - Produktanforderungen - Teil 2-109: Rundsteckverbinder - Bauartspezifikation fr Steckverbinder M 12 x 1 mit Schraubverriegelung fr Datenbertragungen bis 500 MHz (IEC 61076-2-109:2014) This Europea
8、n Standard was approved by CENELEC on 2014-06-12. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references c
9、oncerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELE
10、C member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav R
11、epublic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardiz
12、ation Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61076-2-109
13、:2014 E BS EN 61076-2-109:2014EN 61076-2-109:2014 - 2 - Foreword The text of document 48B/2369/FDIS, future edition 1 of IEC 61076-2-109, prepared by SC 48B “Connectors” of IEC/TC 48 “Electromechanical components and mechanical structures for electronic equipment” was submitted to the IEC-CENELEC pa
14、rallel vote and approved by CENELEC as EN 61076-2-109:2014. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2015-03-12 latest date by which the national standards conflic
15、ting with the document have to be withdrawn (dow) 2017-06-12 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The te
16、xt of the International Standard IEC 61076-2-109:2014 was approved by CENELEC as a European Standard without any modification. BS EN 61076-2-109:2014- 3 - EN 61076-2-109:2014 Annex ZA (normative) Normative references to international publications with their corresponding European publications The fo
17、llowing documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When a
18、n International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu Publication Year Title EN/HD Year IEC 60050 Ser
19、ies International Electrotechnical Vocabulary (IEV) - - IEC 60068-1 2013 Environmental testing - Part 1: General and guidance EN 60068-1 2014 IEC 60068-2-60 1995 Environmental testing - Part 2: Tests - Test Ke: Flowing mixed gas corrosion test EN 60068-2-60 1996 IEC 60352 Series Solderless connectio
20、ns EN 60352 series IEC 60512 Series Connectors for electronic equipment - Tests and measurements EN 60512-1 series IEC 60512-29-100 1)- Connectors for electronic equipment - Tests and measurements - Part 29-100: Signal integrity tests up to 500 MHz on M12 style connectors - Tests 29a to 29g EN 60512
21、-29-100 1)- IEC 60529 A1 A2 1989 1999 2013 Degrees of protection provided by enclosures (IP Code) EN 60529 corr. May A1 A2 1991 1993 2000 2013 IEC 60603-7 A1 2008 2011 Connectors for electronic equipment - Part 7: Detail specification for 8-way, unshielded, free and fixed connectors EN 60603-7 A1 20
22、09 2011 IEC 60603-7-1 - Connectors for electronic equipment - Part 7-1: Detail specification for 8-way, shielded, free and fixed connectors EN 60603-7-1 - IEC 60664-1 2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests EN 60664-1 2007 1)
23、At draft stage. BS EN 61076-2-109:2014EN 61076-2-109:2014 - 4 - IEC 60998-2-1 (mod) 2002 Connecting devices for low-voltage circuits for household and similar purposes - Part 2-1: Particular requirements for connecting devices as separate entities with screw-type clamping units EN 60998-2-1 2004 IEC
24、 60999 Series Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units EN 60999 Series IEC 61076-1 - Connectors for electronic equipment - Product requirements - Part 1: Generic specification EN 61076-1 - IEC 61076-2 2011 Connectors for
25、 electronic equipment - Product requirements - Part 2: Sectional specification for circular connectors EN 61076-2 2011 IEC 61076-2-101 2012 Connectors for electronic equipment - Product requirements - Part 2-101: Circular connectors - Detail specification for M12 connectors with screw-locking EN 610
26、76-2-101 2012 IEC 61984 2008 Connectors - Safety requirements and tests EN 61984 2009 ISO 1302 - Geometrical Product Specifications (GPS) - Indication of surface texture in technical product documentation EN ISO 1302 - ISO/IEC 11801 2002 Information technology - Generic cabling for customer premises
27、 - - BS EN 61076-2-109:2014 2 IEC 61076-2-109:2014 IEC 2014 CONTENTS INTRODUCTION . 6 1 Scope 8 2 Normative references 8 3 Technical information 9 3.1 Terms and definitions . 9 3.2 Recommended method of termination 9 3.2.1 General 9 3.2.2 Number of contacts or contact cavities . 9 3.3 Ratings and ch
28、aracteristics 9 3.4 Marking 10 3.5 Safety aspects . 10 4 Dimensions . 10 4.1 General 10 4.2 Survey of styles and variants . 10 4.3 Interface dimensions for connectors . 11 4.3.1 Interface dimensions for connector type X 11 4.3.2 Interface dimensions for connector type H 14 4.3.3 Pin front view of co
29、nnectors and contact position 14 4.4 Gauges 15 4.4.1 Sizing gauges and retention force gauges 15 5 Characteristics 15 5.1 Climatic category . 15 5.2 Electrical 15 5.2.1 Rated voltage Rated impulse voltage Pollution degree 15 5.2.2 Voltage proof 16 5.2.3 Current-carrying capacity 16 5.2.4 Contact res
30、istance 16 5.2.5 Insulation resistance . 16 5.3 Mechanical 16 5.3.1 IP degree of protection . 16 5.3.2 Mechanical operation 16 5.3.3 Insertion and withdrawal forces 17 5.3.4 Contact retention in insert . 17 5.3.5 Polarizing method . 17 5.3.6 Vibration (sinusoidal) 17 5.3.7 Shock . 17 6 Test schedule
31、 18 6.1 General 18 6.1.1 Introductory remarks . 18 6.1.2 Arrangement for contact resistance measurements . 18 6.1.3 Arrangement for dynamic stress tests (vibration) 19 6.2 Test schedule 20 6.2.1 Test group P Preliminary . 20 6.2.2 Test group AP Dynamic/ climatic . 21 BS EN 61076-2-109:2014IEC 61076-
32、2-109:2014 IEC 2014 3 6.2.3 Test group BP Mechanical endurance 23 6.2.4 Test group CP Electrical load 24 6.2.5 Test group DP Chemical resistivity 25 6.2.6 Test group EP Connection method tests 25 6.2.7 Test group FP Electrical transmission requirements . 25 Annex A (informative) Contact and pair des
33、ignation for balanced cabling . 29 A.1 Recommendation for cable connection . 29 Figure 1 Interface dimensions for connectors type X with female contacts . 11 Figure 2 Interface dimensions for connectors type X with male contacts 12 Figure 3 Interface dimensions for connectors type H with male contac
34、ts 14 Figure 4 Gauge dimensions . 15 Figure 5 Contact resistance arrangement . 19 Figure 6 Dynamic stress test arrangement . 19 Table 1 Contact termination . 9 Table 2 Interface dimensions, connector type X with female contacts 12 Table 3 Interface dimensions, connector type X with male contacts . 1
35、3 Table 4 Interface dimensions for connectors type H with male contacts . 14 Table 5 Gauges . 15 Table 6 Climatic category 15 Table 7 Rated voltage Impulse voltage Pollution degree 16 Table 8 Voltage proof, r.m.s. withstand voltages 16 Table 9 Number of mechanical operations . 17 Table 10 Insertion
36、and withdrawal forces . 17 Table 11 Number of test specimens . 18 Table 12 Test group P . 20 Table 13 Test group AP (1 of 2) . 21 Table 14 Test group BP . 23 Table 15 Test group CP . 24 Table 16 Test group DP . 25 Table 17 Test group EP . 25 Table 18 Test group FP (1 of 2) . 27 Table A.1 Example of
37、contact and pair designation for balanced cabling (informative) . 29 BS EN 61076-2-109:2014 6 IEC 61076-2-109:2014 IEC 2014 INTRODUCTION The International Electrotechnical Commission (IEC) draws attention to the fact that it is claimed that compliance with this document may involve the use of a pate
38、nt concerning connector given in 4.3.2. IEC takes no position concerning the evidence, validity and scope of this patent right. The holder of this patent right has assured the IEC that he/she is willing to negotiate licences free of charge with applicants throughout the world. In this respect, the s
39、tatement of the holder of this patent right is registered with IEC. Information may be obtained from: Tyco Electronics Corporation Licensing Council, Tyco Electronics Technology Resources Inc. 4550 New Linden Hill Road, Suite 140 Wilmington, DE 19808 USA Attention is drawn to the possibility that so
40、me of the elements of this document may be the subject of patent rights other than those identified above. IEC shall not be held responsible for identifying any or all such patent rights. ISO (www.iso.org/patents) and IEC (http:/patents.iec.ch) maintain on-line data bases of patents relevant to thei
41、r standards. Users are encouraged to consult the data bases for the most up to date information concerning patents. BS EN 61076-2-109:2014IEC 61076-2-109:2014 IEC 2014 7 INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC SC 48B Connectors IEC 61076-2-109 Ed. 1.0 ELECTRONIC COMPONENTS in accordance with I
42、EC 61076-1 Type X Type H IEC 1225/14 Circular connectors M12 1 mm 2 to 8 ways, for data transmission frequencies up to 500 MHz Pin and socket connectors with round contact Rewireable Non-rewirable Free cable connectors Straight and right angle connectors Fixed connectors Flange mounting Rear mountin
43、g Single hole mounting BS EN 61076-2-109:2014 8 IEC 61076-2-109:2014 IEC 2014 CONNECTORS FOR ELECTRONIC EQUIPMENT PRODUCT REQUIREMENTS Part 2-109: Circular connectors Detail specification for connectors with M 12 x 1 screw-locking, for data transmission frequencies up to 500 MHz 1 Scope This part of
44、 IEC 61076 describes circular connectors with IP 65/IP 67 degree of protection and suitable for data transmission with frequencies up to 500 MHz. Applications include, but are not limited to, vision systems and data acquisition. These connectors consist of fixed and free connectors, either rewireabl
45、e or non-rewireable, with M12 x 1 screw-locking. Male connectors have round contacts 0,6 mm. This standard covers two different types of connectors, denominated X and H, with different contact arrangement, not mutually interchangeable, but with common ratings and purposes. 2 Normative references The
46、 following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60050
47、(all parts), International Electrotechnical Vocabulary (available at http:/www.electropedia.org) IEC 60068-1:2013, Environmental testing Part 1: General and guidance IEC 60068-2-60:1995, Environmental testing Part 2: Tests Test Ke: Flowing mixed gas corrosion test IEC 60352 (all parts), Solderless c
48、onnections IEC 60512 (all parts), Connectors for electronic equipment Tests and measurements IEC 60512-29-100: Connectors for electronic equipment Tests and measurements Part 29-100: Signal integrity tests up to 500 MHz on M12 style connectors Tests 29a to 29g (to be published) IEC 60529:1989, Degrs
49、 de protection procurs par les enveloppes (Code IP) Amendement 2:2013 Amendement 1:1999 IEC 60603-7:2008, Connectors for electronic equipment Part 7: Detail specification for 8-way, unshielded, free and fixed connectors Amendment 1:2011 IEC 60603-7-1, Connectors for electronic equipment Part 7-1: Detail specification for 8-way, shielded, free and fixed connectors BS EN 61076-2-109:2014IEC 61076-2-109
