1、Radio-frequency connectors - Part 32: RF coaxial connectors with inner diameter of outer conductor 1,85 mm (0,072 in) with screw coupling - Characteristic impedance 50 ohms (type 1,851 The European Standard EN 61169421999 has the status of a Britishstandard ICs 33.120.30 NO COPYING WITHOUT BSI PERMI
2、SSION EXCEPT AS PERMIITED BY COPYRIGHT LAW BS EN 61169-32:2000 dimction of the Electrotechnical Amd. No. Date Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 January ZOO0 National foreword Comments This British Standard is the English langua
3、ge version of EN 61 169-32 1999. It is identical with IEC 61169-321999. The UK participation in its preparation was entsusted by Technical Committee EmJ46, Cables, wires, waveguides, RF connectors and accessories for communication and signalling., to Subcommittee EPVW, RF connectors and waveguides,
4、which has the responsibility to: - aid enquirers to understand the text; - present to the responsible intedonaUEuropean committee any enquiries on the interpretation, or proposals for change, and keep the UK interesls informed; - monitor related internationai and European developments and promulgate
5、 them in the UK. A list of organizations represented on this Subcommittee can be obtained on request to its secretary. From 1 Januay 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the ch
6、ange over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards nody include an annex which lists normative references to intedonai publications with their corresponding European
7、publications. The British Standards which impiement internationai or European publications referred to in this document may be found in the BI Standards Catalogue under the section entitled “Intemational Standards Correspondence Index”, or by using the “Fhd” facility of the BSI Stanauge retention re
8、silient contacts inner contact ;entre contact captivation . axial force . permitted displacement each direction . torque ingagement and separation Screw coupling :oupling torque - coupling nut friction - normal - proof Tensile strength of coupling mechanism Effectiveness of cable fixing against; I)
9、cable rotation Il) cable pulling Il) cable bending IV) cable torsion Bending moment Bump Vibration Shock iC 61169-1 iubclause 9.2.9 9.3.2 9.3.4 9.3.5 9.3.6 9.3.1 1 9.3.7.2 9.3.8 9.3.9 9.3.10 9.3.12 9.3.13 9.3.3 9.3.14 W Lb24hb 082517b 3T9 m Page 11 EN 61169-321999 Value ee detail lecification ee det
10、ail Decification ee detail pecification ,25 N ON lee detail pecification i.010 Nm max 1.8 Nm ),8 Nm to 1,l Nm 1,65 Nm 147 N See detail specification 133 N (RG405) See detail specification 0,l Nm (RG405) See detail specification See detail specification 98 m/s* 10 Hz to 2 O00 Hz 490 rnlsz !4 sine 11
11、rns Remarks, including any deviations from standard test methods (tinction voltages chievable by hand Joint of application and juration Duration of applied torque ielative to reference plane (10 g acceleration) (50 g acceleration) O BSI 01-2000 Page 12 EN 61169-32:1999 Ratings and characteristics En
12、 vironmental Preferred climatic categories Components cables: - flexible cables: - semi-rigid Sealing (panel and barrier sealed connector) Sealing (hermetically sealed connector) Additional environmental characteristics Endurance Mechanical High temperature Salt mist Additional endurance characteris
13、tics Chemical contamination Resistance to solvents and contaminating fluids, fluids to be used. Sulphur dioxide exposure IEC 61169-1 Subclause ).4.6 j.4.8 Value 55/125/21 55/125/21 5511 15/21 1 cmVh max 5 Pa cmVs See detail specification See detail specification See detail specification See detail s
14、pecification See detail specification See detail specification See detail specification Remarks, including any deviations from standard test methods 100kPa-110kPa pressure differential 100kPa-110kPa Dressure differential Q BSI 01-2000 STD-BSI BS EN bLZb9-32-ENGL 2000 1624669 0825378 173 Page 13 EN 6
15、1169-32:1999 3.3 Test schedule and inspection requirements Acceptance tests Group A I Visual examination Group BI Outline dimensions Mechanical compatibility Engagement and separation Gauge retention (resilient contact) Sealing, non-hermetic Sealing, hermetic Voltage proof Solderability piece parts
16、Insulation resistance Test method Subclause EC 61169-1 9.1.2 9.1.3.1 9.1.3.3 9.3.6 9.3.4 9.4.5.1 9.4.5.2 9.2.6 9.3.2.1.1 9.2.5 Assessment level M (Higher) Test re- quired a a a a ia ia a ia a - IL II - s4 II s4 II II II s4 s4 s4 - AQL x 1 ,o - 0,4 1 ,o 0,40 1 ,o 0,65 0,015 0,40 0,40 0,40 Period Lot
17、by lot 3.3.1 Periodic tests There are no Group C tests for levels H and M. NOTE - For details of symbols, abbreviations and procedures see 3.4. Assessment level H (Lower) - Test re- luired a a a a ia ia ia a ia a - IL - 53 - s3 s3 53 s3 s3 s3 II s3 s3 - AQL % - 1,5 Period Lot by lot O BSI 01-2000 ST
18、D-BSI BS EN bllb9-32-ENGL 2000 m 1ib2+669 0825379 008 m Group Di (d) Solderability connector assemblies Resistance to soldering heat Mechanical tests on cable fixing; i) cable rotation (nutation) i) cable pulling iii) cable bending iv) cable torsion Group 02 (d) Contact resistance, outer conductor a
19、nd screen continuity centre conductor continuity Vibration Damp heat steady state Page 14 Periodic tests (continued) EN 61169-321999 Test Method Subclause IEC 61 169-1 9.3.2.1.1 9.3.2.1.2 9.3.7.2 9.3.8 9.3.9 9.3.10 9.2.3 9.3.3 9.4.3 Assessment level H (Lower) Test re- quired ia ia ia ia a a a a Asse
20、ssment level M (Higher) Number of spe- cimens 6 6 1* Group 05 (d) Reflection factor .- Permitted failures per group 9.2.1 quired cimens Permitted failures per groul: Period 3 years Period 1 1 3 years 3 years 3 ia ia 1 1 3 years 3 years 3 years 3 years Group D3 1 3 years 1 9.1.3.2 I Dimensions piece-
21、parts and materials 1 3 years 1 Group 04 (d) Mechanical endurance High temperature endurance Sulphur dioxide 9.5 9.6 9.4.8 1 3 years 13 1 Try ia f a Screening effectiveness I 9.2.8 Water immersion 9.2.7 1 3 years 1 3 years Group D6 (d) Contact captivation Rapid change of temperature Climatic sequenc
22、e Group 07 (d) Resistance to solvents and contaminating fluids 9.3.5 9.4.4 9.4.2 9.7 3 years 3 years NOTE - For details of symbols, abbreviations and procedures, see 3.4. O ES1 01-2000 Page 15 EN 61169-32:1999 3.4 Procedures 3.4.1 Quality conformance inspection This shall consist of Test Groups Al a
23、nd B1 on a lot-by-lot basis. 3.4.2 This shall consist of three consecutive lots passing Test Groups AI and Bl followed by selection of specimens from the lots as appropriate. These specimens shall successfully pass the specified periodic D tests. Details of symbols, abbreviations and procedures: Qua
24、lification approval and its maintenance a= ia = na = IL = AQL = *= #= = (dl = suggested as applicable test suggested (if technically applicable) not applicable Inspection Level Acceptable Quality Level One set of piece-parts each style and variant, unless using common piece parts For Qualification A
25、pproval (QA) a total of 2 failures only permitted for level H and 1 failure only for level M from groups DI to D7 Group D7 - number of pairs for each solvent destructive tests - specimens shall not be returned to stock 4 Instructions for preparation of detail specifications 4.1 General Detail Specif
26、ication (DS) writers shall use the appropriate BDS pro-forma. The following pages comprise the pro-forma BDS dedicated for use with 50 R type 1,85 connectors. As such, it will have already entered on it information relating to: a) the basic specification number applicable to all the detail specifica
27、tions covering b) the connector series designation. The specification writer should enter the details relating to the connector style/variant(c) to be covered as indicated. The numbers in brackets on the BDS pro-forma correspond to the following indications which shall be given. connector styles of
28、the series covered by the Sectional Specification; 8 BSI 01-2000 STD=BSI BS EN hLLb7-32-ENGL 2000 Lb24669 0825383 7bb Page 16 4.2 (1) The name of the National Standards Institution under whose authority the DS is published and, if applicable, the organization from whom the DS is available. (2) The n
29、umber allocated to the DS by the relevant National Authorized institution immediately preceded by the IS0 two letter national identity code or XX when DS is produced by an IEC technical committee. (3) The number and issue number of the IEC generic specification and, when applicable, the sectional sp
30、ecification; also the national reference, if different. (4) If different from the IEC number, the national number of the DS, date of issue and any further information required by the national system, together with any amendment numbers. EN 61169-32:1999 Identification of the detail specification 4.3
31、 Identification of the component (5) Enter the following details: Style: Attachment: The style designation of the connector including type of fixing and sealing, if applicable. By deletion of the inapplicable options of cable/wire: given for centre and outer conductors. Special features and markings
32、: As applicable. (6) Enter details of assessment level and the climatic category. (7) A reproduction of the outline drawing and details of the panel piercing, if applicable. It shall provide the maximum envelope dimensions, also the position of the reference plane and, in the case of a fixed connect
33、or, the position of the mounting plane(s) relative to the front face of the connector. Any maximum panel thickness limitations for fixed connectors shall be stated. (8) Particulars of all variants covered by the DS. As appropriate, the information shall include: 0 0 o 0 cable types (or sizes) applic
34、able to each variant. alternative plated or protective finishes. details of alternative mounting flanges having either tapped or plain mounting holes. details of alternative solder spills or solder buckets including, when applicable, those for use with Microwave Integrated Circuit (MIC) components.
35、4.4 Performance (9) Performance data listing the most important characteristics of the connector taking into account the recommended values in 3.2 of this specification. Deviations from the minimum requirements shall be clearly indicated. Non-applicable parameters shall be marked “na“. 4.5 Additiona
36、l information (10) Insert marking and ordering information as appropriate, together with details of related documents and any invoked structural similarity. O BSI 01-2000 Page 17 EN 61169-32:1999 4.6 Selection of tests, test conditions and severities (11) “na“ shall be used to indicate non-applicabl
37、e tests. All tests marked “a“ by the detail specification writer shall be mandatory. When using the normal procedure with a dedicated BDS, the letter “a“ - for “applicable“ - shall be entered in the “Test required“ column against each of the tests indicated as being mandatory in the test schedule of
38、 3.3 of this specification. Any additional tests required at the discretion of the specification writer shall also be indicated by an “a“. The specification writer shall also indicate, when necessary, details of deviations from the standard test methods and test conditions, including any relevant de
39、viations given in the test schedule of the sectional specification. The qualification approval and conformance inspection shall be such that the NSI shall be satisfied that they are appropriate and in line with those for other connectors within the system providing a reasonably comparable service. O
40、 BSI 01-2000 STDmBSI BS EN bL1b9-32-ENGL 2000 = Lb24bb9 0825183 539 Style:, Page 18 4.7 The following pages contain the complete BDS pro-forma. EN 61169-32:1999 Blank detail specification pro-forma for type 1,85 connector Special features and markings ELECTRONIC COMPONENT OF ASSESSED QUALITY IN ACCO
41、RDANCE WITH GENERIC SPECIFICATION QC 220000 SECTIONAL SPECIFICATION QC 221600 NATIONAL REFERENCE (6) Assessment level . Characteristic impedance 50 R page 1 of 10 (2) # IECQ Logo Climatic category /./.I QC 221701 (8) Variants ISSUE I Type 1,85 I. . . . (7) Outline and maximum dimensions Panel pierci
42、ng and mounting details For mating interface dimensions and position of reference plane see QC 221600 Maximum panel thickness: for front mounting mm, for rear mounting mm Variant No. o1 . . . . . . Description of variant . . . . . . . . . 60096 IEC . . . . . . . . . . . . . . . . . . . . . . . . . .
43、 . . . . . Information about manufacturers who have components qualified to this detail specification is available in the current QC 001005 Qualified Product List. Note # Insert IS0 national identity code or “XX“ if completed by IEC committee. O BSI 01-2000 STD.BS1 BS EN bIlb9-32-ENGL 2000 H 2624bb9
44、 0825284 475 Page 19 EN 61169-32:1999 (9) Performance (including limiting conditions of use) Ratings and characteristics Electrical Nominal impedance Frequency range Reflection factor Variant No. Designation o1 . Centre contact resistance Centre conductor continuity Outer conductor continuity Insula
45、tion resistance +Voltage proof at sea level +Voltage proof at 4-4 kPa +Environment test voltage at sea level Environment test voltage at 4,4 kPa o1 . . o1 . o1 . . o1 . o1 . . IEC 61 169-1 QC 220000 Subclause 9.2.1 9.2.3 9.2.3 9.2.3 9.2.5 9.2.6 Value 50 R . . . 5 . mo I ma . mS1 . mo . mR . mS1 I .
46、mo 2 .GR 2 . GR . kV . kV . kV . kV . v .v .v .v .v .v .v .v . v Remarks, including any deviations from standard test methods Measurement frequency range initial after conditioning Resistance change due to conditioning initial after conditioning initial after conditioning 86 kPa to 106 kPa . kPa (if
47、 not 4,4 kPa) 86 kPa to 106 kPa . kPa (if not 4,4 kPa) + = Voltage are r.m.s. values of a.c. at 40 Hz to 65 Hz unless otherwise stated. 0 BSI 01-2000 STD.BSI BS EN blbbS-32-ENGL 2000 lb24bb 0825185 301 m Page 20 EN 61169-321999 Ratings and characteristics .Electrical (continued) Screening effectiven
48、ess o1 . ADDITIONAL ELECTRICAL CHARACTERISTICS Mechanical Soldering - bit size Gauge retention resilient contacts - inner contact - outer contact Centre contact captivation - axial force - permitted displacement each direction Engagement and separation - axial force Effectiveness of cable fixing aga
49、inst i) cable rotation o1 . i) cable pulling o1 . iii) cable bending o1 . . IEC 61169-1 QC 220000 Subclause 9.2.8 9.3.2.1 .I 9.3.4 9.3.5 9.3.6 9.3.7 9.3.8 9.3.9 Value 2 dB at GHz . . N . .mm Rotations . N . Cycles . . Remarks, including any deviations from standard test methods z, 2 n For gauging details see figure 5 of QC 221600 (see figure 5 of IEC 61 169-19) Length of cable Mass . . . O BSI 01-2000 STDmBSI BS EN bLLb9-32-ENGL 2000 Ratings and characteristics Mechanical (continued) iv) cable torsion o1 . Bending moment Vibration ADDITIONAL MECHANICAL CHARACTERISTICS En vi
