1、BSI Standards PublicationFibre optic interconnecting devices and passive components Basic test and measurement proceduresPart 2-44: Tests Flexing of the strain relief of fibre optic devicesBS EN 61300-2-44:2013National forewordThis British Standard is the UK implementation of EN 61300-2-44:2013. It
2、isidentical to IEC 61300-2-44:2013. It supersedes BS EN 61300-2-44:2008which is withdrawn.The UK participation in its preparation was entrusted by TechnicalCommittee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre opticinterconnecting devices and passive components.A list of organizations repr
3、esented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2013.Published by BSI Standards Limited 2013ISBN 978 0 580
4、 78245 9ICS 33.180.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 September 2013.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STAN
5、DARDBS EN 61300-2-44:2013EUROPEAN STANDARD EN 61300-2-44 NORME EUROPENNE EUROPISCHE NORM September 2013 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Aven
6、ue Marnix 17, B - 1000 Brussels 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61300-2-44:2013 E ICS 33.180.20 Supersedes EN 61300-2-44:2008 English version Fibre optic interconnecting devices and passive components - Basic
7、test and measurement procedures - Part 2-44: Tests - Flexing of the strain relief of fibre optic devices (IEC 61300-2-44:2013) Dispositifs dinterconnexion et composants passifs fibres optiques - Procdures fondamentales dessais et de mesures - Partie 2-44: Essais - Flexion du serre-cble des dispositi
8、fs fibres optiques (CEI 61300-2-44:2013) Lichtwellenleiter-Verbindungselemente und passive Bauteile- Grundlegende Prf und Messverfahren - Teil 2-44: Prfungen - Biegen der Zugentlastung von Lichtwellenleiterbauteilen (IEC 61300-2-44:2013) This European Standard was approved by CENELEC on 2013-08-19.
9、CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained
10、on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the
11、 CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hun
12、gary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 61300-2-44:2013EN 61300-2-44:2013 - 2 - Foreword The text of document 86B/3499/CDV, future edi
13、tion 3 of IEC 61300-2-44, prepared by SC 86B, “Fibre optic interconnecting devices and passive components“, of IEC TC 86, “Fibre optics“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-2-44:2013. The following dates are fixed: latest date by which the document has
14、to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-05-19 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2014-08-19 This document supersedes EN 61300-2-44:2008. EN 61300-2-44:2013 incl
15、udes the following significant technical changes with respect to EN 61300-2-44:2008: a) revision of Figure 1; b) change of fibre length from the flex point to the weight. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and
16、/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61300-2-44:2013 was approved by CENELEC as a European Standard without any modification. BS EN 61300-2-44:2013- 3 - EN 61300-2-44:2013 Annex ZA (normativ
17、e) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated
18、references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 61300-1 - Fibre optic interconnecting
19、devices and passive components - Basic test and measurement procedures - Part 1: General and guidance EN 61300-1 - IEC 61300-3-1 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-1: Examinations and measurements - Visual examination EN 6130
20、0-3-1 - IEC 61300-3-3 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-3: Examinations and measurements - Active monitoring of changes in attenuation and return loss EN 61300-3-3 - IEC 61300-3-4 - Fibre optic interconnecting devices and pa
21、ssive components - Basic test and measurement procedures - Part 3-4: Examinations and measurements - Attenuation EN 61300-3-4 - IEC 61753-1 - Fibre optic interconnecting devices and passive components performance standard - Part 1: General and guidance for performance standards EN 61753-1 - BS EN 61
22、300-2-44:2013 2 61300-2-44 IEC:2013(E) CONTENTS 1 Scope . 5 2 Normative references 5 3 General description . 5 4 Apparatus . 5 4.1 General . 5 4.2 Optical source (S) 6 4.3 Detector (D) . 7 4.4 Mounting fixture . 7 4.5 Flex test machine or jig 7 5 Procedure . 7 5.1 Preparation of specimens 7 5.2 Prec
23、onditioning 7 5.3 Initial measurements 7 5.4 Conditioning 7 5.5 Recovery . 8 5.6 Final measurements 8 6 Severity 8 7 Details to be specified . 9 Figure 1 Apparatus for testing 6 Figure 2 Application of the load in the case of duplex cordage 6 Table 1 Severities 8 BS EN 61300-2-44:201361300-2-44 IEC:
24、2013(E) 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 2-44: Tests Flexing of the strain relief of fibre optic devices 1 Scope This part of IEC 61300 specifies a test to determine the influence of flexing under tensile load of the strain relie
25、f of fibre optic devices. The intention is to simulate the number of flexing cycles which would typically be experienced during service life. This test is applied to both single fibre cable and multiple fibre cable. 2 Normative references The following documents, in whole or in part, are normatively
26、 referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61300-1, Fibre optic interconnecting devices and passive compone
27、nts Basic test and measurement procedures Part 1: General and guidance IEC 61300-3-1, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-1: Examinations and measurements Visual examination IEC 61300-3-3, Fibre optic interconnecting devices and pas
28、sive components Basic test and measurement procedures Part 3-3: Examinations and measurements Active monitoring of changes in attenuation and return loss IEC 61300-3-4, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-4: Examinations and measure
29、ments Attenuation IEC 61753-1, Fibre optic interconnecting devices and passive components performance standard Part 1: General and guidance for performance standards 3 General description The device under test (DUT) is rotated 90 in the plane of the cable about an axis perpendicular to the axis of t
30、he attached cable and in the case of ribbon cable, parallel to the width of the ribbon. This causes flexing of the strain relief and cable close to the DUT. During the flexing, a tensile force, but no torque, is applied. 4 Apparatus 4.1 General The apparatus for testing and the flexing patterns invo
31、lved are presented in Figure 1. BS EN 61300-2-44:2013 6 61300-2-44 IEC:2013(E) 0 90 +90 25 cm 5 cm DUT Weight Tensile Detector Mounting plate Source IEC 1603/13 Figure 1 Apparatus for testing In the case of duplex cordage or ribbon, the loads shall not be doubled and the cable shall be bent in the m
32、inor axis direction as shown in Figure 2. Figure 2 Application of the load in the case of duplex cordage The equipment used is that indicated in 4.2 to 4.5. 4.2 Optical source (S) The recommended source shall be in accordance with IEC 61300-3-3 and IEC 61300-3-4 as appropriate. Duplex cordage Load I
33、EC 1276/04 BS EN 61300-2-44:201361300-2-44 IEC:2013(E) 7 4.3 Detector (D) The recommended detector shall be in accordance with IEC 61300-3-3 and IEC 61300-3-4 as appropriate. 4.4 Mounting fixture The mounting fixture rigidly holds the fibre optic DUT in correct alignment during the test. If the devi
34、ce is a fibre optic connector, an adaptor or a receptacle may be used as a mounting fixture. The fixture shall not distort the DUT. The fixture shall allow the DUT to be connected to monitoring equipment. 4.5 Flex test machine or jig A machine or jig that can rotate the DUT 90ofrom a straight positi
35、on while applying a load to the fibre or cable. 5 Procedure 5.1 Preparation of specimens Prepare and clean the specimen in accordance with the manufacturers instructions. Visually check that the attachment of the cable to the fibre optic device is not damaged in accordance with IEC 61300-3-1. Fibre
36、length from the flex point to the weight: 25 cm 5 cm. Fibre length is measured from the point of flexing to the point of application of the load. 5.2 Preconditioning Pre-condition the specimen and all equipment for 2 h at the standard test conditions as defined in IEC 61300-1, unless otherwise speci
37、fied in the relevant specification. 5.3 Initial measurements Complete initial examinations and measurements on the specimen as required by the relevant specification. 5.4 Conditioning Install the DUT on the apparatus. Measure the attenuation of the DUT with the flexing arm in a vertical position in
38、accordance with IEC 61300-3-4. Apply the specified tensile load and apply the specified number of flexes. Use gentle rotational movements, not exceeding 20 cycles/min. The dwell at each extreme shall be not greater than 5 s. Measure the change in attenuation during test in accordance with IEC 61300-
39、3-3. Stop the flexing with the flexing arm in vertical position. Remove the tensile force. BS EN 61300-2-44:2013 8 61300-2-44 IEC:2013(E) 5.5 Recovery Allow the DUT to remain under standard test conditions for 2 h, as defined in IEC 61300-1, unless otherwise specified in the relevant specification.
40、Clean the DUT in accordance with the manufacturers instructions. 5.6 Final measurements Remove the DUT from the apparatus and make final measurements, as defined by the relevant specification, to ensure that there is no permanent damage to the DUT. The results of the final measurement shall be withi
41、n the limit established in the relevant specification. Visually check that the attachment of the cable to the fibre optic DUT is not damaged in accordance with IEC 61300-3-1. 6 Severity Severity is specified by the magnitude of tensile force and the number of cycles +90 to 90. Recommended values of
42、the test parameters are given in Table 1. Table 1 Severities Category aComponent type Tensile force N Number of cycles C Connectors Reinforced cable 2 100 C Passive components Reinforced cable 2 30 U and E Connectors Reinforced cable 5 100 U and E Passive components Reinforced cable 5 30 O Passive c
43、omponents Reinforced jacketed cables 5 30 Primary and secondary coated fibre 2 30 O Connectors Reinforced jacketed cables 8,9 100 bSFF connectors 5,9 100 baCategory can be found in IEC 61753-1. bApplied at 25 cm 5 cm from cable entrance to plug. BS EN 61300-2-44:201361300-2-44 IEC:2013(E) 9 7 Detail
44、s to be specified The relevant specification shall specify the following details: magnitude of tensile force; number of flexes; applicable optical fibre cable (type, length, etc.); initial examination and measurements and performance requirements; permitted change of attenuation during test; final e
45、xamination and measurements and performance requirements; pass/fail decision criterion; deviations from test procedure. _ BS EN 61300-2-44:2013This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-re
46、lated publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together bus
47、iness, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations
48、of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or K
49、nowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Subs
