1、 STD-BSI BS EN b1300-3-36-ENGL 2000 D Lb24bb9 OBblbb5 Ob3 = BRITISH STANDARD _ Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-36: Examinations and measurements - Measurement methods for the inside and outside diameters of fibre optic conne
2、ctor ferrules The European Stands British Standard 61300-3-36:2000 has the stab of a ICs 33.180.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 6 1300-3-36:2000 IEC 61300-3-36:2000 STDIBSI BS EN bL300-3-36-ENGL 2000 .I Lb24669 OBbLbbb TTB been prepared under the direc
3、tion of the Electrotechmcal Sector Committee, was published under the authority of the Standards Conunittee and comes into effect on 15 August ZOO0 bd. No. O BSI 08-2000 ISBN O 580 36199 3 BS EN 61300-3362000 Date Comments National foreword This British Standard is the official English language vers
4、ion of EN 61300-3-362000. It is identical with IEC: 613-3-362000. The UK participation in its preparation was entrusted by Technical Committee GEU86, Fibre optics, to GEL/86/2, Interconnecting devices and passive components, which has the responsibihty to: - aid enquirers to understand the text; - p
5、resent to the responsible intematio - monitor related international and European developments and promulgate them in the UK A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to t
6、he old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time dunng the change over fi.om one numbering cyctem to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normall
7、y include an annex which lists normative references to international publications with the& corresponding European publications. The British Standards which implement international or European publications referred to in this document niay be found in the BSI Standards Catalogue under the section en
8、titled “International Standards Correspondence Index”, or by using the “Find facility of the BSI Standards Electxonic Catalogue. A British Standard dots not purport to include aJl the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compli
9、ance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 10, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicate
10、s when the document was last issued. STD.BSI BS EN bL300-3-3b-ENGL 2000 3b24bh OBbLbb7 934 = EN 61 300-3-36 EUROPEAN STANDARD NORME EUROPEENNE EUROPISCHE NORM May 2000 ICs 33.1 80.20 English version Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part
11、 3-36: Examinations and measurements - Measurement methods for the inside and outside diameters of fibre optic connector ferrules (IEC 61 300-3-36:2000) Dispositifs dinterconnexion et composants passifs fibres optiques Mthodes fondamentales dessais et de mesures Partie 3-36: Examens et mesures Mthod
12、es de mesure des diamtres intrieurs et extrieurs des embouts de connecteurs pour fibres optiques (CE1 61 300-3-36:2000) Lichtwellenleiter-Verbindungselemente und passive Bauteile Grundlegende Prf- und Messverfahren Teil 3-36: Untersuchungen und Messungen - Messverahren fr den Innen- und Aussendurchm
13、esser von Stiften fr LWL-Steckverbinder (IEC 61 300-3-3612000) This European Standard was approved by CENELEC on 2000-04-01. CENELEC members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standar
14、d without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretanat or to any CENELEC member. This European Standard exists in three offiaal versions (English, French, German). A version in any other la
15、nguage made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, Fran
16、ce, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comite Europeen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung C
17、entral Secretariat: rue de Stassart 35, B - 1050 Brussels (D 2000 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. NO. EN 61 300-3-36:2000 E STD.BS1 BS EN bL300-3-3b-ENGL 2000 Lb24bb O8bLbb8 870 Page 2 EN 61300-3-36:2000 Foreword The text
18、 of document 86B/128UFDIS, future edition 1 of IEC61300-3-36, prepared by SC866, Fibre optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submittted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61 300-3-36 on 2000-04-01. The following dates we
19、re fixed: - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement - latest date by which the national standards conflicting with the EN have to be withdrawn (dop) 2001-01-01 (dow) 2003-04-01 Endorsement notice The text
20、of the international Standard IEC 61300-3-36:2000 was approved by CENELEC as a European Standard without any modification. STD.BSI BS EN b1300-3-3b-ENGL 2000 - Lb24bb OBbLbbq 707 Page 3 EN 61300-3-362000 CONTENTS Page Clause 1 Scope 4 2 Normative references 4 3 Measurement methods for the inside dia
21、meter of fibre optic connector ferrules 4 3.1 Purpose 4 3.2 General description 4 3.3 Inspection method: pin gauging technique . 5 3.3.1 Gauging of ferrules 5 3.3.2 Inspection conditions . 5 3.3.3 Inspection procedure . 6 Details to be specified 6 3.4 4 Measurement methods for the outside diameter o
22、f fibre optic connector ferrules . 6 4.1 Purpose 6 4.2 General description 6 4.3 Inspection methods . 7 Method 2: laser and contact micrometer measurement techniques . 8 4.3.1 4.3.2 4.3.3 4.4.1 Method 1 . 10 4.4.2 Method 2 . 10 Method 1 : ring gauging technique 7 Method 3: displacement measurement t
23、echnique . 9 Details to be specified 10 4.4 4.4.3 Method 3 . 10 Figure 1 . Pin gauging tolerance field of ferrule hole 5 Figure 2 - Ring gauging tolerance field of ferrule outside diameter . 7 O BSI 08-2000 STD-BSI BS EN bL300-3-3b-ENGL 2000 E Lb24bb9 OBbLb70 429 II Page 4 EN 61300-3-36:2000 FIBRE O
24、PTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - BASIC TEST AND MEASUREMENT PROCEDURES - Part 3-36: Examinations and measurements - Measurement methods for the inside and outside diameters of fibre optic connector ferrules 1 Scope This International Standard describes the measurement methods of
25、 the inside diameter of fibre optic connector ferrules. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of the
26、se publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referr
27、ed to applies. Members of IS0 and IEC maintain registers of currently valid International Standards. None. 3 Measurement methods for the inside diameter of fibre optic connector ferrules 3.1 Purpose The purpose of this procedure is to inspect and measure the inside diameter of the precision hole of
28、fibre optic connector ferrules. The precision hole aligns and positions the optical fibre inside the ferrule. The procedure described here uses the “GO“ and “NO-GO“ gauging technique. 3.2 General description The most commonly used inspection method for the inside diameter is the GO and NO-GO pin gau
29、ging technique. Due to the very small inside diameters of the connector ferrules for commonly used single mode and multimode ferrules, accurate direct measurement is difficult to achieve. One technique is the direct measurement of the inside diameter of a ferrule precision alignment hole. This can b
30、e carried out either by projecting the ferrule hole using a projection optical microscope or by using an imaging and digitizing system to measure the bore diameter. Thesr techniques tend to suffer from inaccuracy in determining the inside edges of a precision hole. Thus, the use of “pin gauges“ beca
31、me the most common method for determining the inside diameter of a ferrule manufactured to specified dimensional limits. O BSI 08-2000 STD.BSI BS EN bL300-3-3b-ENGL 2000 9 Lb24bb9 OBbLb7l 365 Tolerance of the hole diameter 4 b + b Hole LL Hole UL - GO pin gauge tolerance field Page 6 EN 61300-3-36:2
32、000 f-, NO-GO pin gauge tolerance field 3.3 The pin gauges shall be made from hard-wearing material, such as tungsten carbide, ruby or hard ceramic and shall be rigid. Inspection method: pin gauging technique 3.3.1 GO pin gauge: Gauging of ferrules (see figure 1) The diameter of the pin gauge shall
33、be equal to or larger than the lower limit of the specified inside diameter of the ferrule. It shall be capable of gauging the entire length of the hole. NO-GO pin gauge: The diameter of the pin gauge shall be equal to or larger than the upper limit of the specified diameter of the ferrule. 3.3.2 In
34、spection conditions GO pin gauge Key LL Lower limit UL Upper limit NO-GO pin gauge IEC 107RoOO Figure 1 - Pin gauging tolerance field of ferrule hole a) The inspection shall be carried out in an environmentally controlled location. The environ- mental temperature shall be within limits determined by
35、 the tolerance of the measurement and the thermal expansion values of the pin gauge and the ferrule material under inspection. b) The pin gauges shall be kept free from contamination and shall be thoroughly cleaned before use. c) Measure the diameter of the pin gauge before inserting into the ferrul
36、es, using a suitably calibrated instrument having sufficient accuracy. d) The diameter of the pin gauges or the instrument used for their calibration shall be certified and periodically verified by an accredited laboratory. O BSI 08-2000 Page 6 EN 6 1300-3 -3 6 :2000 3.3.3 Inspection procedure a) Th
37、oroughly clean the pin gauges before use, using alcohol and a lint-free tissue. b) Gently insert the GO pin gauge into the precision hole of the ferrule under inspection until the pin is fully inserted. c) When inserting the pin gauge into the ferrule hole, ensure that the axis of the pin gauge is i
38、n line with the axis of the ferrule, thus preventing angular misalignment of the pin gauge. d) When inserting a pin gauge into the ferrule hole, the ferrule can be gently rotated around the common axis (along the length of the ferrule). e) If the GO gauge fails to pass through the ferrule, the ferru
39、le is rejected. f) Gently attempt to insert the NO-GO pin gauge into the ferrule precision hole. g) If the NO-GO gauge enters the ferrule, the ferrule is rejected. 3.4 Details to be specified Upper and lower limits of the hole diameter. The length of the ferrule. The length of the precision hole. Th
40、e length of the pin gauge. Diameter and tolerance of the GO and NO-GO pin gauges Roundness of the pin gauges. The uniformity of the diameter of the pin gauges. The roughness of the surface finish of the pin gauge. The tolerance on the diameter of the pin gauges. 4 Measurement methods for the outside
41、 diameter of fibre optic connector ferrules 4.1 Purpose The purpose of these procedures is to inspect and measure the outside diameter of fibre optic connector ferrules. The procedures described here use the ring GO and NO-GO gauging technique or contact and non-contact micrometer and laser diameter
42、 measurement techniques. 4.2 General description One method used to inspect the diameter of fibre optic connector ferrules is the ring GO and NO-GO gauging technique. The ferrule diameter can also be measured directly by using other suitable techniques. Conformity of the outside diameter of fibre op
43、tic connector ferrules to the agreed dimensions and tolerances is necessary for proper performance. O BSI 08-2000 STD*BSI BS EN b3300-3-3b-ENGL 2000 36246b9 0863673 138 W NO-GO ring gauge - tolerance field Page 7 EN 6 1300-3-362000 GO ring gauge tolerance field 4.3 Inspection methods 4.3.1 The ring
44、gauges shall be made from hard-wearing material, such as tungsten carbide, ruby or hard ceramic and shall be rigid. The inside surface of the ring gauge shall be smooth and cylindrical. Method 1: ring gauging technique 4.3.1 .I Gauging of ferrules (see figure 2) GO ring gauge: The inside diameter of
45、 the ring gauge shall be equal to or smaller than the upper limit of the specified outside diameter of the ferrule. NO-GO ring gauge: The inside diameter of the ring gauge shall be equal to or larger than the lower limit of the specified outside diameter of the ferrule. 4.3.1.2 Inspection conditions
46、 LL UL NO-GO ring gauge LL UL GO ring gauge IEC 108/2000 Key LL Lower limit UL Upper limit Figure 2 - Ring gauging tolerance field of ferrule outside diameter a) The number of insertions in the ring gauges shall be noted. b) The inspection shall be carried out in an environmentally controlled locati
47、on. The environ- mental temperature should be kept within limits determined by the tolerance of the measurement and the thermal expansion values of the ring gauge and the ferrule material under inspection. c) The ring gauges shall be kept free from contamination and shall be cleaned thoroughly befor
48、e use. d) The inside diameter of the ring gauge shall meet specifications for roundness, cylindricity, and surface finish. O BSI 08-2000 STD-BSI BS EN bL300-3-3h-ENGL 2000 II 1624669 OBbLb74 O74 II Page 8 EN 61300-3-36:2000 e) Measure the diameter of the ring gauges before insertion of the ferrules,
49、 using a suitably calibrated instrument having sufficient accuracy. f) The diameter of the ring gauges or the instrument used for their calibration shall be certified and periodically verified by an accredited laboratory. 4.3.1.3 Inspection procedure a) Thoroughly clean the ring gauges before use, using alcohol and a lint-free tissue. b) Gently insert the ferrule into the GO ring gauge until it has passed through the gauge. If the ferrule fails to pass through the GO gauge, the ferrule is rejected. c) Repeat item b) above with the NO-GO ring gauge. if th
