1、BSI Standards PublicationFibre optic active components and devices Test and measurement proceduresPart 3: Optical power variation induced by mechanical disturbance in optical receptacles and transceiver interfacesBS EN 62150-3:2015National forewordThis British Standard is the UK implementation of EN
2、 62150-3:2015. It isidentical to IEC 62150-3:2015. It supersedes BS EN 62150-3:2012 which iswithdrawn.The UK participation in its preparation was entrusted by TechnicalCommittee GEL/86, Fibre optics, to Subcommittee GEL/86/3, Fibre optic systems and active devices.A list of organizations represented
3、 on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 83712
4、8ICS 33.180.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 September 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS
5、EN 62150-3:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 62150-3 August 2015 ICS 33.180.20 Supersedes EN 62150-3:2012 English Version Fibre optic active components and devices - Test and measurement procedures - Part 3: Optical power variation induced by mechanical disturbance in optical
6、receptacles and transceiver interfaces (IEC 62150-3:2015) Composants et dispositifs actifs fibres optiques - Procdures fondamentales dessais et de mesures - Partie 3: Variation de puissance optique induite par des perturbations mcaniques dans les interfaces dembases et dmetteurs-rcepteurs optiques (
7、IEC 62150-3:2015) Aktive Lichtwellenleiter-Bauteile und -Bauelemente - Grundlegende Prf- und Messverfahren - Teil 3: Optische Leistungsabweichungen bedingt durch mechanische Strungen in optischen Kupplungen und Transceiver-Schnittstellen (IEC 62150-3:2015) This European Standard was approved by CENE
8、LEC on 2015-06-11. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standar
9、ds may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language
10、and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, G
11、ermany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalis
12、ation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 62150-3:2015 E BS EN 62150-3:2015EN 62150-
13、3:2015 2 European foreword The text of document 86C/1311/FDIS, future edition 2 of IEC 62150-3, prepared by SC 86C “Fibre optic systems and active devices“ of IEC/TC 86 “Fibre optics“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 62150-3:2015. The following dates are f
14、ixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2016-03-11 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2018-06-11 This document supersedes
15、 EN 62150-3:2012. EN 62150-3:2015 includes the following significant technical changes with respect to EN 62150-3:2012: extension of application field to SC connector interface transceivers in addition to LC connector interface transceivers specified in the first edition as both transceiver interfac
16、es are very important in the industry; addition of a new Annex E dealing with load value difference for connector type in Method A. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible f
17、or identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 62150-3:2015 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicate
18、d: IEC 61300 Series NOTE Harmonized as EN 61300 Series. IEC 61754-4 NOTE Harmonized as EN 61754-4. IEC 61754-20 NOTE Harmonized as EN 61754-20. BS EN 62150-3:2015EN 62150-3:2015 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications T
19、he following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 W
20、hen an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu Publication Year Title EN/HD Year IEC 6175
21、3 Series Fibre optic interconnecting devices and passive components - Performance standard EN 61753 Series IEC 61753-021-6 - Fibre optic interconnecting devices and passive components performance standard - Part 021-6: Grade B/2 single-mode fibre optic connectors for category O - Uncontrolled enviro
22、nment EN 61753-021-6 - IEC 61754 Series Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces EN 61754 Series BS EN 62150-3:2015 2 IEC 62150-3:2015 IEC 2015 CONTENTS FOREWORD . 4 1 Scope 6 2 Normative references 6 3 Terms, definitions and abbreviations . 6 3.1
23、 Terms and definitions 6 3.2 Abbreviations 7 4 Measurement consideration . 7 4.1 Multiple test methods 7 4.2 Two wiggle loss mechanisms 7 Rationale for two different wiggle loss test methods . 7 4.2.1Case A: Point of action for the ferrule 7 4.2.2Case B: Point of action for the plug housing 8 4.2.35
24、 Test Method A . 8 5.1 Apparatus . 8 General . 8 5.1.1Test cord . 8 5.1.2Power meter 8 5.1.3Test load . 8 5.1.45.2 Test procedures for Tx interfaces 9 Test procedures . 9 5.2.1Set-up . 9 5.2.2Initial measurement . 9 5.2.3Apply load and rotate . 9 5.2.4Wiggle loss 9 5.2.55.3 Test procedures for Rx in
25、terfaces and optical receptors 10 Test procedures . 10 5.3.1LOS indicator method 10 5.3.2Receiver optical power monitor method . 10 5.3.36 Test Method B . 11 6.1 Apparatus . 11 General . 11 6.1.1Test fixture and rotation mechanism 11 6.1.2Test cord . 11 6.1.3Power meter 12 6.1.4Test load . 12 6.1.56
26、.2 Test procedures for Tx interfaces 12 Test procedures . 12 6.2.1Set-up . 12 6.2.2Initial measurement . 12 6.2.3Apply load . 12 6.2.4Measurement . 12 6.2.5Wiggle loss 12 6.2.66.3 Test procedures for Rx interfaces and optical receptors 13 Test procedures . 13 6.3.1LOS-indicator method 13 6.3.2Receiv
27、er optical power monitor method . 13 6.3.3BS EN 62150-3:2015IEC 62150-3:2015 IEC 2015 3 7 Test results . 14 Annex A (normative) Load requirements 15 A.1 Loads for Method A . 15 A.2 Loads for Method B . 15 Annex B (normative) Summary of test conditions . 16 Annex C (normative) Characteristics of the
28、test cord 17 Annex D (normative) Floating tolerance . 20 Annex E (informative) Load value difference for connector type in Method A . 21 Bibliography 22 Figure 1 Equipment setup of Method A for Tx interfaces 10 Figure 2 Equipment set-up of Method A for Rx interfaces and optical receptors . 11 Figure
29、 3 Equipment set-up of Method B for Tx interfaces . 13 Figure 4 Equipment set-up of Method B for Rx interface and optical receptors . 14 Figure C.1 Wiggle test cord interface (LC connector) . 17 Figure C.2 Wiggle test cord interface (SC connector) . 18 Figure D.1 Floating tolerance . 20 Figure E.1 F
30、loating tolerance . 21 Table 1 Multiple test methods 7 Table A.1 Method A: Loads applied for devices using connector cords with 1,25 mm ferrule and 2,5 mm ferrule . 15 Table A.2 Method B: Loads applied for devices using connector cords with 1,25 mm ferrule and 2,5 mm ferrule . 15 Table B.1 Summary o
31、f test conditions for Method A (normative) 16 Table B.2 Summary of test conditions for Method B (normative) 16 Table C.1 Wiggle test cord specification (LC connector) 17 Table C.2 Dimensions of the wiggle test cord interface 18 Table C.3 Wiggle test cord specification (SC connector) 18 Table C.4 Dim
32、ensions of the wiggle test cord interface 19 BS EN 62150-3:2015 4 IEC 62150-3:2015 IEC 2015 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES TEST AND MEASUREMENT PROCEDURES Part 3: Optical power variation induced by mechanical disturbance in optical receptacles a
33、nd transceiver interfaces FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concern
34、ing standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
35、preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates clos
36、ely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the releva
37、nt subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the te
38、chnical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum e
39、xtent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provi
40、de conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or i
41、ts directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses
42、 arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attentio
43、n is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62150-3 has been prepared by subcommittee 86C: Fibre optic systems and acti
44、ve devices, of IEC technical committee 86: Fibre optics. This second edition cancels and replaces the first edition published in 2012 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: extension of application
45、 field to SC connector interface transceivers in addition to LC connector interface transceivers specified in the first edition as both transceiver interfaces are very important in the industry; addition of a new Annex E dealing with load value difference for connector type in Method A. BS EN 62150-
46、3:2015IEC 62150-3:2015 IEC 2015 5 The text of this standard is based on the following documents: FDIS Report on voting 86C/1311/FDIS 86C/1330/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has b
47、een drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 62150 series, published under the general title Fibre optic active components and devices Test and measurement procedures, can be found on the IEC website. The committee has decided that the contents of thi
48、s publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of th
49、is publication may be issued at a later date. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. BS EN 62150-3:2015 6 IEC 62150-3:2015 IEC 2015 FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES TEST AND MEASUREMENT PROCEDURES Part 3: Optical power variation
