1、BRITISH STANDARDBS EN 62384:2006DC or AC supplied electronic control gear for LED modules Performance requirementsICS 29.140.99; 31.080.99g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3
2、g38g50g51g60g53g44g42g43g55g3g47g36g58+A1:2009National forewordThis British Standard is the UK implementation of EN 62384:2006+A1:2009. It is identical to IEC 62384:2006, incorporating amendment 1:2009. It supersedes BS EN 62384:2006 which will be withdrawn on 1 August 2012.The UK participation in i
3、ts preparation was entrusted by Technical Committee CPL/34, Lamps and related equipment, to Subcommittee CPL/34/3, Auxiliaries for lamps.A list of organizations represented on this subcommittee can be obtained on request to its secretary. This publication does not purport to include all the necessar
4、y provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. BS EN 62384:2006+A1:2009This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 Novemb
5、er 2006 BSI 2009Amendments/corrigenda issued since publicationDate Comments 31 December 2009 Implementation of IEC amendment 1:2009 with CENELEC endorsement A1:2009; Figure A.1 replacedISBN 978 0 580 63312 6EUROPEAN STANDARD EN 62384:2006+A1 NORME EUROPENNE EUROPISCHE NORM September 2009 CENELEC Eur
6、opean Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide f
7、or CENELEC members. Ref. No. EN 62384:2006 E ICS 29.140.99; 31.080.99 English version DC or AC supplied electronic control gear for LED modules - Performance requirements (IEC 62384:2006) Appareillages lectroniques aliments en courant continu ou alternatif pour modules de DEL - Exigences de performa
8、nces (CEI 62384:2006) Gleich- oder wechselstromversorgte elektronische Betriebsgerte fr LED-Module - Anforderungen an die Arbeitsweise (IEC 62384:2006) This European Standard was approved by CENELEC on 2006-09-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which st
9、ipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Stan
10、dard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the natio
11、nal electrotechnical committees of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerl
12、and and the United Kingdom. Foreword The text of document 34C/752/FDIS, future edition 1 of IEC 62384, prepared by SC 34C, Auxiliaries for lamps, of IEC TC 34, Lamps and related equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 62384 on 2006-09-01. This stan
13、dard is to be used in conjunction with EN 61347-2-13. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2007-06-01 latest date by which the national standards conflicting with t
14、he EN have to be withdrawn (dow) 2009-09-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 62384:2006 was approved by CENELEC as a European Standard without any modification. _ EN 62384:2006+A1:2009 2 Foreword to amendment A1 The text of document
15、34C/869/CDV, future amendment 1 to IEC 62384:2006, prepared by SC 34C, Auxiliaries for lamps, of IEC TC 34, Lamps and related equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 62384:2006 on 2009-08-01. The following dates were fixed: latest d
16、ate by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2010-05-01 latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2012-08-01 _ Endorsement notice The text of ame
17、ndment 1:2009 to the International Standard IEC 62384:2006 was approved by CENELEC as an amendment to the European Standard without any modification. _ BS EN 62384:2006+A1:2009 3 EN 62384:2006+A1:2009CONTENTS 1 Scope 4 2 Normative references .4 3 Terms and definitions .4 4 General notes on tests5 5
18、Classification5 5.1 Classification according to the load 5 5.2 Classification according to the output voltage .6 5.3 Classification according to the output current .6 6 Marking 6 6.1 Mandatory marking 6 6.2 Optional marking .6 7 Output voltage and current .6 7.1 Starting and connecting requirements
19、6 7.2 Voltage and current during operation .7 7.3 Capacitive load requirement.7 7.4 Voltage surges during switching and operation .7 8 Total circuit power 7 9 Circuit power factor 7 10 Supply current 7 11 Impedance at audio-frequencies .8 12 Operational tests for abnormal conditions8 13 Endurance8An
20、nex A (normative) Tests .10 Annex B (informative) A guide to quoting product life and failure rate 13Annex ZA (normative) Normative references to international publications with their corresponding European publications 15 Bibliography. 14 BS EN 62384:2006+A1:2009EN 62384:2006+A1:2009 4 DC OR AC SUP
21、PLIED ELECTRONIC CONTROL GEAR FOR LED MODULES PERFORMANCE REQUIREMENTS 1 Scope This international standard specifies performance requirements for electronic control gear foruse on d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz with anoutput frequency which can deviate fr
22、om the supply frequency, associated with LED modulesaccording to IEC 62031. Control gear for LED modules specified in this standard are designedto provide constant voltage or current. Deviations from the pure voltage and current types donot exclude the gear from this standard. NOTE 1 The tests in th
23、is standard are type tests. Requirements for testing individual control gear duringproduction are not included. NOTE 2 Requirements for control gear which incorporate means for varying the output power are underconsideration. NOTE 3 It may be expected that control gear complying with this standard w
24、ill ensure satisfactory operationbetween 92 % and 106 % of the rated supply voltage, taking into account the specifications of the LED modulemanufacturer. 2 Normative references The following referenced documents are indispensable for the application of this document.For dated references, only the e
25、dition cited applies. For undated references, the latest editionof the referenced document (including any amendments) applies. IEC 61347-2-13, Lamp controlgear Part 2-13: Particular requirements for d.c. or a.c.supplied electronic control gear for LED modules IEC 62031, LED modules for general light
26、ing Safety requirements 1 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 total circuit power total power dissipated by control gear and LED module(s) in combination, at rated supplyvoltage of the control gear and at the highest rated output
27、load. 3.2 circuit power factor ratio of the measured circuit power to the product of the supply voltage (r.m.s.) and the supplycurrent (r.m.s.). 3.3 high audio-frequency impedance control gear control gear the impedance of which in the frequency range 250 Hz to 2 000 Hz exceeds thevalues specified i
28、n Clause 11 of this standard. BS EN 62384:2006+A1:2009 5 EN 62384:2006+A1:20094 General notes on tests 4.1 The tests according to this standard are type tests. NOTE The requirements and tolerances permitted by this standard are based on testing of a type test samplesubmitted by the manufacturer for
29、that purpose. In principle this type test sample should consist of units havingcharacteristics typical of the manufacturers production and be as close to the production centre point values aspossible. It may be expected with the tolerances given in the standard that products manufactured in accordan
30、ce with thetype test sample will comply with the standard for the majority of the production. Due to the production spreadhowever, it is inevitable that there will sometimes be products outside the specified tolerances. For guidance ofsampling plans and procedures for inspection by attributes, see I
31、EC 60410. 4.2 For tests which are carried out with a LED module or LED modules, this (these) LEDmodule(s) shall fulfil the following requirements: The wattage of the LED module(s) when measured at its(their) rated voltage or rated current(d.c. and/or a.c.) shall not differ from the rated wattage by
32、more than +6 % and 0 %. 4.3 The tests shall be carried out in the order of the clauses, unless otherwise specified. 4.4 One specimen shall be submitted to all the tests. 4.5 In general all the tests are made on each type of control gear or, where a range ofsimilar control gear is involved for each r
33、ated wattage in the range or on a representativeselection from the range as agreed with the manufacturer. 4.6 The tests shall be made under the conditions specified in Clause A.1. Since up to nowdata of LED modules are not published in an IEC standard, they shall be made available bythe LED module m
34、anufacturer. 4.7 All control gear covered by this standard shall comply with the requirements ofIEC 61347-2-13. 4.8 The tests shall be carried out with the length of the output cable of both 20 cm and200 cm unless otherwise declared by the manufacturer. 5 Classification 5.1 Classification according
35、to the load a) Single value load control gear This type of control gear is designed for use with one specific output wattage only, whichmay be dissipated by one or more LED modules. b) Multiple value load control gear This type of control gear is designed for use with one or more LED modules with a
36、totalload within the declared wattage range. BS EN 62384:2006+A1:2009EN 62384:2006+A1:2009 6 5.2 Classification according to the output voltage a) Control gear having a stabilised output voltage b) Control gear without a stabilised output voltage 5.3 Classification according to the output current a)
37、 Control gear having a stabilised output current b) Control gear without a stabilized output current 6 Marking 6.1 Mandatory marking 6.1.1 Control gear shall be clearly marked as follows: Circuit power factor; e.g. = 0,9 If the power factor is less than 0,95 leading, it shall be followed by the lett
38、er “C”, e.g. = 0,9 C. 6.1.2 In addition to the above mandatory marking, the following information shall either begiven on the control gear or made available in the manufacturers catalogue or the like: a) if applicable: limits of the permissible temperature range; b) if applicable: an indication that
39、 the control gear has a stabilised output voltage; c) if applicable: an indication that the control gear has a stabilised output current; d) if applicable: an indication that the control gear is suitable for operation with a mainssupply dimmer; e) if applicable: an indication of the operation mode,
40、e.g. phase control. 6.2 Optional marking The following information may either be given on the control gear or made available in themanufacturers catalogue or the like: a) total circuit power; b) if applicable: the symbol Z which indicates that the control gear is designed to complywith conditions fo
41、r audio-frequency impedance; c) If applicable: a symbol which indicates that the control gear is a short-circuit proof type(the symbol is under consideration). 7 Output voltage and current 7.1 Starting and connecting requirements After starting or connecting a LED module, the output should be within
42、 110 % of its ratedvalue within 2 s. Maximum current or maximum voltage shall not exceed the values given bythe manufacturer. This performance is tested with the minimum rated power. NOTE If the output voltage is a.c., 110 % is the percentage of the r.m.s. value, if d.c., 110 % is the percentage oft
43、he d.c. value. BS EN 62384:2006+A1:2009 7 EN 62384:2006+A1:2009 7.2 Voltage and current during operation For control gear having a non-stabilised output voltage, when supplied with the rated supplyvoltage, the output voltage shall not differ by more than 10 % from the rated voltage of theLED modules
44、; for control gear having a stabilised output voltage when supplied at any supplyvoltage between 92 % and 106 % of the rated supply voltage, the output voltage shall notdiffer by more than 10 % from the rated voltage of the LED modules. For control gear having a non-stabilised output current, when s
45、upplied with the rated supplyvoltage, the output current shall not differ by more than 10 % from the rated current of theLED modules; for control gear having a stabilised output current when supplied at any supplyvoltage between 92 % and 106 % of the rated supply voltage, the output current shall no
46、tdiffer by more than 10 % from the rated current of the LED modules. Multiple load control gear shall be tested with both the minimum and maximum load. 7.3 Capacitive load requirement If the LED module or any additional control unit connected to the convertor contain capacitorsfor control and/or dri
47、ving circuitry on the modules, current pulses may be generated whenconnecting the LED module to the control gear. This shall not disturb the control gearovercurrent detection nor the starting process of the control gear. For test conditions, See clause A.2. Figure A.1a describes a test circuit durin
48、g the startingprocess of the control gear and figure A.1b describes a test circuit for connecting the loadduring steady state operation. Compliance: when connecting the measurement circuit to the control gear, the detectiondevice shall not trip. 7.4 Voltage surges during switching and operation Volt
49、age surges superimposed on the output voltage shall not exceed the values specifiedbelow (values under consideration). 8 Total circuit power At rated voltage, the total circuit power shall not be more than 110 % of the value declared bythe manufacturer, when the control gear is operated with LED module(s). 9 Circuit power factor The measured circuit power factor shall not be less than the marked value by more than 0,05when the control gear is operated on its rated wattage with LE
