1、BSI Standards PublicationDigital addressable lighting interface Part 103: General requirements Control devicesBS EN 62386-103:2014National forewordThis British Standard is the UK implementation of EN 62386-103:2014. It isidentical to IEC 62386-103:2014.The UK participation in its preparation was ent
2、rusted by TechnicalCommittee CPL/34, Lamps and Related Equipment, to SubcommitteeCPL/34/3, Auxiliaries for lamps.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Us
3、ers are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 62956 3ICS 29.140; 29.140.50 Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the aut
4、hority of theStandards Policy and Strategy Committee on 31 January 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 62386-103:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 62386-103 December 2014 ICS 29.140; 29.140.50 English Version Digital addre
5、ssable lighting interface - Part 103: General requirements - Control devices (IEC 62386-103:2014) Interface dclairage adressable numrique - Partie 103: Exigences gnrales - Dispositifs de commande (CEI 62386-103:2014) Digital adressierbare Schnittstelle fr die Beleuchtung - Teil 103: Allgemeine Anfor
6、derungen - Steuergerte (IEC 62386-103:2014) This European Standard was approved by CENELEC on 2014-12-12. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alter
7、ation. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language
8、made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czec
9、h Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kin
10、gdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CENELEC All rights of exploitation in any form and by any means reserve
11、d worldwide for CENELEC Members. Ref. No. EN 62386-103:2014 E BS EN 62386-103:2014EN 62386-103:2014 - 2 - Foreword The text of document 34C/1100/FDIS, future edition 1 of IEC 62386-103, prepared by SC 34C “Auxiliaries for lamps“ of IEC/TC 34 “Lamps and related equipment“ was submitted to the IEC-CEN
12、ELEC parallel vote and approved by CENELEC as EN 62386-103:2014. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2015-09-12 latest date by which the national standards co
13、nflicting with the document have to be withdrawn (dow) 2017-12-12 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice T
14、he text of the International Standard IEC 62386-103:2014 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: CISPR 15 NOTE Harmonized as EN 55015. IEC 60598-1 NOTE Harmon
15、ized as EN 60598-1. IEC 60669-2-1 NOTE Harmonized as EN 60669-2-1. IEC 60921 NOTE Harmonized as EN 60921. IEC 60923 NOTE Harmonized as EN 60923. IEC 60929 NOTE Harmonized as EN 60929. IEC 61347-1 NOTE Harmonized as EN 61347-1. IEC 61347-2-3 NOTE Harmonized as EN 61347-2-3. IEC 61547 NOTE Harmonized
16、as EN 61547. IEC 62034 NOTE Harmonized as EN 62034. BS EN 62386-103:2014- 3 - EN 62386-103:2014 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this docu
17、ment and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicate
18、d by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu Publication Year Title EN/HD Year IEC 62386-101 2014 Digital addressable lighting interface - Part 101: General requirements -
19、 System Components EN 62386-101 2014 IEC 62386-102 2014 Digital addressable lighting interface - Part 102: General requirements - Control gear EN 62386-102 2014 BS EN 62386-103:2014 2 IEC 62386-103:2014 IEC 2014 CONTENTS INTRODUCTION . 13 1 Scope 15 2 Normative references 15 3 Terms and definitions
20、15 4 General . 18 4.1 General . 18 4.2 Version number 18 5 Electrical specification . 18 6 Interface power supply 18 7 Transmission protocol structure . 18 7.1 General . 18 7.2 24 bit forward frame encoding . 19 Frame format for instructions and queries 19 7.2.1Frame format for event messages 20 7.2
21、.28 Timing . 21 9 Method of operation . 21 9.1 General . 21 9.2 Application controller 21 General . 21 9.2.1Single-master application controller . 22 9.2.2Multi-master application controller . 22 9.2.39.3 Input device 22 9.4 Instances of input devices . 23 General . 23 9.4.1Instance number 23 9.4.2I
22、nstance type . 23 9.4.3Feature type 23 9.4.4Instance groups . 24 9.4.59.5 Commands . 24 General . 24 9.5.1Device commands . 24 9.5.2Instance commands . 25 9.5.3Feature commands 25 9.5.49.6 Event messages . 25 Response to event messages 25 9.6.1Device power cycle event 25 9.6.2Input notification even
23、t 25 9.6.3Event message filter 26 9.6.49.7 Input signal and input value 27 General . 27 9.7.1Input resolution 27 9.7.2Getting the input value . 27 9.7.3Notification of changes 28 9.7.49.8 System failure . 28 BS EN 62386-103:2014IEC 62386-103:2014 IEC 2014 3 9.9 Operating a control device 29 Enable/d
24、isable the application controller 29 9.9.1Enable/disable event messages . 29 9.9.2Quiescent mode 29 9.9.3Modes of operation 30 9.9.49.10 Memory banks 30 General . 30 9.10.1Memory map 31 9.10.2Selecting a memory bank location . 31 9.10.3Memory bank reading 32 9.10.4Memory bank writing 32 9.10.5Memory
25、 bank 0 33 9.10.6Memory bank 1 35 9.10.7Manufacturer specific memory banks . 37 9.10.8Reserved memory banks . 37 9.10.99.11 Reset 37 Reset operation . 37 9.11.1Reset memory bank operation . 37 9.11.29.12 Power on behaviour 37 Power on . 37 9.12.1Power cycle notification . 38 9.12.29.13 Priority use
26、. 38 General . 38 9.13.1Priority of input notifications 38 9.13.29.14 Assigning short addresses 39 General . 39 9.14.1Random address allocation 39 9.14.2Identification of a device 39 9.14.39.15 Exception handling . 40 9.16 Device capabilities and status information 40 Device capabilities . 40 9.16.1
27、Device status . 40 9.16.2Instance status 41 9.16.39.17 Non-volatile memory . 41 10 Declaration of variables . 42 11 Definition of commands . 43 11.1 General . 43 11.2 Overview sheets . 43 11.3 Event messages . 48 INPUT NOTIFICATION (device/instance, event) 48 11.3.1POWER NOTIFICATION (device) . 48 1
28、1.3.211.4 Device control instructions 48 General . 48 11.4.1IDENTIFY DEVICE 48 11.4.2RESET POWER CYCLE SEEN 49 11.4.311.5 Device configuration instructions. 49 General . 49 11.5.1RESET 49 11.5.2RESET MEMORY BANK (DTR0) 49 11.5.3BS EN 62386-103:2014 4 IEC 62386-103:2014 IEC 2014 SET SHORT ADDRESS (DT
29、R0) . 49 11.5.4ENABLE WRITE MEMORY 49 11.5.5ENABLE APPLICATION CONTROLLER 50 11.5.6DISABLE APPLICATION CONTROLLER . 50 11.5.7SET OPERATING MODE (DTR0) . 50 11.5.8ADD TO DEVICE GROUPS 0-15 (DTR2:DTR1) 50 11.5.9ADD TO DEVICE GROUPS 16-31 ( DTR2:DTR1 ) 50 11.5.10REMOVE FROM DEVICE GROUPS 0-15 (DTR2:DTR
30、1) 50 11.5.11REMOVE FROM DEVICE GROUPS 16-31 (DTR2:DTR1) 50 11.5.12START QUIESCENT MODE 50 11.5.13STOP QUIESCENT MODE 50 11.5.14ENABLE POWER CYCLE NOTIFICATION . 51 11.5.15DISABLE POWER CYCLE NOTIFICATION 51 11.5.16SAVE PERSISTENT VARIABLES 51 11.5.1711.6 Device queries 51 General . 51 11.6.1QUERY D
31、EVICE CAPABILITIES 51 11.6.2QUERY DEVICE STATUS . 51 11.6.3QUERY APPLICATION CONTROLLER ERROR 52 11.6.4QUERY INPUT DEVICE ERROR . 52 11.6.5QUERY MISSING SHORT ADDRESS 52 11.6.6QUERY VERSION NUMBER 52 11.6.7QUERY CONTENT DTR0 52 11.6.8QUERY NUMBER OF INSTANCES 52 11.6.9QUERY CONTENT DTR1 52 11.6.10QU
32、ERY CONTENT DTR2 52 11.6.11QUERY RANDOM ADDRESS (H) 53 11.6.12QUERY RANDOM ADDRESS (M) 53 11.6.13QUERY RANDOM ADDRESS (L) . 53 11.6.14READ MEMORY LOCATION (DTR1, DTR0) 53 11.6.15QUERY APPLICATION CONTROL ENABLED . 53 11.6.16QUERY OPERATING MODE . 53 11.6.17QUERY MANUFACTURER SPECIFIC MODE 53 11.6.18
33、QUERY QUIESCENT MODE 53 11.6.19QUERY DEVICE GROUPS 0-7 53 11.6.20QUERY DEVICE GROUPS 8-15 54 11.6.21QUERY DEVICE GROUPS 16-23 54 11.6.22QUERY DEVICE GROUPS 24-31 54 11.6.23QUERY POWER CYCLE NOTIFICATION 54 11.6.24QUERY EXTENDED VERSION NUMBER(DTR0) . 54 11.6.25QUERY RESET STATE . 54 11.6.2611.7 Inst
34、ance control instructions . 54 11.8 Instance configuration instructions 54 General . 54 11.8.1ENABLE INSTANCE 55 11.8.2DISABLE INSTANCE . 55 11.8.3SET PRIMARY INSTANCE GROUP (DTR0) . 55 11.8.4SET INSTANCE GROUP 1 (DTR0) . 55 11.8.5SET INSTANCE GROUP 2 (DTR0) . 55 11.8.6BS EN 62386-103:2014IEC 62386-
35、103:2014 IEC 2014 5 SET EVENT SCHEME (DTR0) 55 11.8.7SET EVENT PRIORITY (DTR0) 56 11.8.8SET EVENT FILTER (DTR2, DTR1, DTR0) 56 11.8.911.9 Instance queries . 56 General . 56 11.9.1QUERY INSTANCE TYPE . 56 11.9.2QUERY RESOLUTION 56 11.9.3QUERY INSTANCE ERROR 56 11.9.4QUERY INSTANCE STATUS . 56 11.9.5Q
36、UERY INSTANCE ENABLED 57 11.9.6QUERY PRIMARY INSTANCE GROUP . 57 11.9.7QUERY INSTANCE GROUP 1 . 57 11.9.8QUERY INSTANCE GROUP 2 . 57 11.9.9QUERY EVENT SCHEME 57 11.9.10QUERY INPUT VALUE 57 11.9.11QUERY INPUT VALUE LATCH 57 11.9.12QUERY EVENT PRIORITY 57 11.9.13QUERY FEATURE TYPE . 58 11.9.14QUERY NE
37、XT FEATURE TYPE . 58 11.9.15QUERY EVENT FILTER 0-7 58 11.9.16QUERY EVENT FILTER 8-15 58 11.9.17QUERY EVENT FILTER 16-23. 58 11.9.1811.10 Special commands 58 General . 58 11.10.1TERMINATE 58 11.10.2INITIALISE (device) 59 11.10.3RANDOMISE . 59 11.10.4COMPARE 59 11.10.5WITHDRAW . 59 11.10.6SEARCHADDRH
38、(data) 60 11.10.7SEARCHADDRM (data) . 60 11.10.8SEARCHADDRL (data) 60 11.10.9PROGRAM SHORT ADDRESS (data) 60 11.10.10VERIFY SHORT ADDRESS (data) . 60 11.10.11QUERY SHORT ADDRESS . 61 11.10.12WRITE MEMORY LOCATION (DTR1, DTR0, data) 61 11.10.13WRITE MEMORY LOCATION NO REPLY (DTR1, DTR0, data) . 61 11
39、.10.14DTR0 (data) . 61 11.10.15DTR1 (data) . 62 11.10.16DTR2 (data) . 62 11.10.17DIRECT WRITE MEMORY (DTR1, offset, data) . 62 11.10.18DTR1:DTR0 (data1, data0) 62 11.10.19DTR2:DTR1 (data2, data1) 62 11.10.20SEND TESTFRAME (data) . 62 11.10.2112 Test procedures 63 12.1 General notes on test 63 Genera
40、l . 63 12.1.1Test execution . 63 12.1.2Data transmission 64 12.1.3BS EN 62386-103:2014 6 IEC 62386-103:2014 IEC 2014 Test setup . 64 12.1.4Test output 64 12.1.5Test notation . 65 12.1.6Test execution limitations 66 12.1.7Test results . 66 12.1.8Exception handling 66 12.1.9Unexpected answer . 66 12.1
41、.1012.2 Preamble 68 Test preamble . 68 12.2.112.3 Physical operational parameters . 79 Polarity test . 79 12.3.1Maximum and minimum system voltage . 80 12.3.2Overvoltage protection test 80 12.3.3Current rating test 81 12.3.4Transmitter voltages 83 12.3.5Transmitter rising and falling edges . 84 12.3
42、.6Transmitter bit timing . 86 12.3.7Transmitter frame timing 88 12.3.8Receiver start-up behavior . 89 12.3.9Receiver threshold . 90 12.3.10Receiver bit timing . 91 12.3.11Extended receiver bit timing 95 12.3.12Receiver forward frame violation 97 12.3.13Receiver settling timing . 97 12.3.14Receiver f
43、rame timing FF-FF send twice 98 12.3.15Transmitter collision avoidance by priority . 100 12.3.16Transmitter collision detection for truncated idle phase 101 12.3.17Transmitter collision detection for extended active phase 104 12.3.1812.4 Device configuration instructions. 107 RESET deviceGroups 107
44、12.4.1RESET quiescentMode 108 12.4.2RESET instance groups . 109 12.4.3RESET event filter . 110 12.4.4RESET event scheme 111 12.4.5RESET: timeout / command in-between . 112 12.4.6Send twice timeout (device) . 114 12.4.7Send twice timeout (instance) 117 12.4.8Commands in-between (device) . 119 12.4.9C
45、ommands in-between (instance) 122 12.4.10SAVE PERSISTENT VARIABLES 125 12.4.11SET OPERATING MODE . 125 12.4.12Device Disable/Enable Application Controller 126 12.4.13Multi Master Control Device PING . 127 12.4.14Quiescent Mode 128 12.4.15Device power cycle notification 129 12.4.16SET SHORT ADDRESS .
46、 130 12.4.17Reset/Power-on values (device) 131 12.4.18Reset/Power-on values (instance) . 133 12.4.19DTR0 / DTR1 / DTR2 . 134 12.4.20BS EN 62386-103:2014IEC 62386-103:2014 IEC 2014 7 DTR1:DTR0 and DTR2:DTR1 135 12.4.21Device Groups . 136 12.4.2212.5 Device queries 137 Device query capabilities . 137
47、12.5.1QUERY VERSION NUMBER 137 12.5.2Device power cycle seen . 138 12.5.3Input device error 138 12.5.412.6 Device Memory banks . 139 READ MEMORY LOCATION on Memory Bank 0 139 12.6.1READ MEMORY LOCATION on Memory Bank 1 144 12.6.2READ MEMORY LOCATION on other Memory Banks 146 12.6.3Memory bank writin
48、g 148 12.6.4ENABLE WRITE MEMORY: writeEnableState 153 12.6.5ENABLE WRITE MEMORY: timeout / command in-between . 155 12.6.6RESET MEMORY BANK: timeout / command in-between 156 12.6.7RESET MEMORY BANK 159 12.6.812.7 Device Special commands 160 INITIALISE timer . 160 12.7.1TERMINATE 161 12.7.2INITIALISE
49、 - device addressing . 162 12.7.3RANDOMISE . 163 12.7.4COMPARE 163 12.7.5WITHDRAW . 165 12.7.6SEARCHADDRH / SEARCHADDRM / SEARCHADDRL . 166 12.7.7PROGRAM SHORT ADDRESS 167 12.7.8VERIFY SHORT ADDRESS . 169 12.7.9QUERY SHORT ADDRESS . 170 12.7.10IDENTIFY DEVICE 172 12.7.1112.8 Logical unit cross contamination . 174 DTR0 . 174 12.8.1NVM variables . 174 12.8.2Random address generation 175 12.8.3Addressing 1 . 176 12.8.4Addressing 2 . 177 12.8.5Addressing 3 . 179 12.8.612.9 Instance addressing 180 Instance Type Addressing . 18
