1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationEnergy performance of lamp controlgearPart 1: Controlgear for fluorescent lamps Method of measurement to determine the total input power of controlgear circuits and the efficienc
2、y of the controlgearBS EN 62442-1:2011National forewordThis British Standard is the UK implementation of EN 62442-1:2011, incorporating CENELEC corrigendum May 2012. It is identical to IEC 62442-1:2011. It supersedes BS EN 50294:1998, which will be with-drawn on 16 November 2014. CENELEC corrigendum
3、 May 2012 adds supersession information to the CENELEC foreword and title page.The UK participation in its preparation was entrusted by Technical Committee CPL/34, Lamps and Related Equipment, to Subcommittee CPL/34/3, Auxiliaries for lamps.A list of organizations represented on this subcommittee ca
4、n be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012.Published by BSI Standards Limited 2012 ISBN 978 0 580 55708 8 ICS 29.140.99;17
5、.220.20Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2012.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 62442-1:
6、2011EUROPEAN STANDARD EN 62442-1 NORME EUROPENNE EUROPISCHE NORM November 2011 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2011
7、CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 62442-1:2011 E ICS 29.140.99 English version Energy performance of lamp controlgear - Part 1: Controlgear for fluorescent lamps - Method of measurement to determine the total input p
8、ower of controlgear circuits and the efficiency of the controlgear (IEC 62442-1:2011) Performance nergtique des appareillages de lampes - Partie 1: Appareillages des lampes fluorescence - Mthode de mesure pour la dtermination de la puissance dentre totale des circuits dappareillage et du rendement d
9、es appareillages (CEI 62442-1:2011) Energieeffizienz von Lampenbetriebsgerten - Teil 1: Betriebsgerte fr Leuchtstofflampen - Messverfahren zur Bestimmung der Gesamteingangsleistung von Betriebsgerteschaltungen und des Wirkungsgrades von Betriebsgerten (IEC 62442-1:2011) This European Standard was ap
10、proved by CENELEC on 2011-11-16. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such na
11、tional standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its
12、 own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
13、Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Supersedes EN 50294:1998 + A1:2001 + A2:2003EN 62442-1:2011 - 2 - Foreword The text of document 34C/987/FDIS, futu
14、re edition 1 of IEC 62442-1, prepared by SC 34C, “Auxiliaries for lamps“, of IEC/TC 34, “Lamps and related equipment“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 62442-1:2011. The following dates are fixed: latest date by which the document has to be implemented at n
15、ational level by publication of an identical national standard or by endorsement (dop) 2012-08-16 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2014-11-16 Attention is drawn to the possibility that some of the elements of this document may be th
16、e subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 62442-1:2011 was approved by CENELEC as a European Standard without any modification. BS EN 62442-1:2011This docum
17、ent supersedes EN 50294:1998 + A1:2001 + A2:2003.- 3 - EN 62442-1:2011 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated reference
18、s, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD
19、Year IEC 60081 - Double-capped fluorescent lamps - Performance specifications EN 60081 - IEC 60901 - Single-capped fluorescent lamps - Performance specifications EN 60901 - IEC 60921 2004 Ballasts for tubular fluorescent lamps - Performance requirements EN 60921 2004 IEC 60929 + corr. September 2011
20、 2011 AC and/or DC-supplied electronic control gear for tubular fluorescent lamps - Performance requirements EN 60929 2011 IEC 61347-2-3 - Lamp controlgear - Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps EN 61347-2-3 - IEC 61347-2-8 - L
21、amp controlgear - Part 2-8: Particular requirements for ballasts for fluorescent lamps EN 61347-2-8 - BS EN 62442-1:2011 2 62442-1 IEC:2011 CONTENTS 1 Scope . 5 2 Normative references 5 3 Terms and definitions . 6 4 General 8 4.1 Applicability . 8 4.2 Declaration of ballast lumen factor . 8 4.3 Dimm
22、able controlgear 8 4.4 Multi-wattage and/or multi-lamp controlgear . 8 4.5 Accuracy of measurement . 8 4.6 Sampling of controlgear for testing . 8 4.7 Number of samples 9 4.8 Conditioning of lamps 9 4.9 Test voltages and frequencies . 9 5 Method of measurement and calculation of total input power of
23、 controlgear lamp circuits and the efficiency of controlgear 9 5.1 Correction for ballast lumen factor . 9 5.2 Method of measurement 9 5.3 Measurement and calculation of the total input power of magnetic wire wound controlgear lamp circuits . 10 5.4 Calculation of the efficiency of magnetic wire wou
24、nd controlgear 10 5.5 Measurement and calculation of the total input power of electronic controlgear lamp circuits 10 5.6 Calculation of the efficiency of electronic controlgear . 12 5.7 Measuring the standby power. 12 Annex A (normative) Energy performance measurement setup . 13 Annex B (informativ
25、e) Application of the reference ballast when assessing lamps in electronic operation . 17 Bibliography 18 Figure 1 Configuration of lamp and photocell sensor . 12 Figure A.1 Measurement of magnetic wire wound controlgear lamp circuits 13 Figure A.2 Measurement of a.c. supplied electronic controlgear
26、 lamp circuits 14 Figure A.3 Test setup for measuring standby power 14 Figure A.4 Side view of light output measurement system . 15 Figure A.5 Top view of light output measurement system 15 Table 1 Typical nominal electricity supply details for some regions 9 BS EN 62442-1:201162442-1 IEC:2011 5 ENE
27、RGY PERFORMANCE OF LAMP CONTROLGEAR Part 1: Controlgear for fluorescent lamps Method of measurement to determine the total input power of controlgear circuits and the efficiency of the controlgear 1 Scope This part of IEC 62442 defines a measurement and calculation method of the total input power fo
28、r controlgear lamp circuits when operating with their associated fluorescent lamp(s). The calculation method for the efficiency of the lamp controlgear is also defined. This International Standard applies to electrical controlgear lamp circuits consisting only of the controlgear and the lamp(s). It
29、is intended for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz. NOTE Requirements for testing individual controlgear during production are not included. It specifies the measurement method for the total input power and the calculation method of the controlgear efficiency for all controlgear us
30、ed for domestic and normal commercial purposes operating with the following fluorescent lamps: linear fluorescent lamps; single-ended (compact) fluorescent lamps; other general purpose fluorescent lamps. This International Standard does not apply to: controlgear which form an integral part of the la
31、mp; controllable wire-wound magnetic controlgear; luminaires, which rely on additional optical performance aspects. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated refe
32、rences, the latest edition of the referenced document (including any amendments) applies. IEC 60081, Double-capped fluorescent lamps Performance specifications IEC 60901, Single-capped fluorescent lamps Performance requirements IEC 60921:2004, Ballasts for tubular fluorescent lamps Performance requi
33、rements IEC 60929:2011, AC and/or DC-supplied electronic control gear for tubular fluorescent lamps Performance requirements IEC 61347-2-3, Lamp control gear Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps IEC 61347-2-8, Lamp controlgear
34、Part 2-8: Particular requirements for ballasts for fluorescent lamps BS EN 62442-1:2011 6 62442-1 IEC:2011 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 nominal value suitable approximate quantity value used to designate or identify a compo
35、nent, device or equipment 3.2 limiting value the greatest or smallest admissible value of one of the quantities 3.3 rated value quantity value for specified operating conditions of a component, device or equipment The value and conditions are specified in the relevant standard or assigned by the man
36、ufacturer or responsible vendor NOTE For the different kinds of operation, rated electrical values are given on the lamp data sheets as: rated electrical values under “electrical characteristics”, if the lamp is defined for 50 Hz / 60 Hz operation only, rated electrical values under “electrical char
37、acteristics”, if the lamp is defined for high frequency ( 20 kHz) operation only, rated electrical values and typical electrical values, if the lamp is defined simultaneously for 50 Hz / 60 Hz operation and high frequency operation for 50 Hz / 60 Hz operation: rated electrical values under “electric
38、al characteristics”, and for high frequency operation: rated electrical values under “typical lamp characteristics”. 3.4 controlgear one or more components between the supply and one or more lamps which may serve to transform the supply voltage, limit the current of the lamp(s) to the required value
39、, provide starting voltage and preheating current, prevent cold starting, correct power factor or reduce radio interference 3.5 electromagnetic controlgear controlgear which by means of inductance, or a combination of inductance and capacitance, serves mainly to limit the current of the lamp(s) to t
40、he required value Frequency of the lamp operation is the same as supply frequency. 3.6 electronic controlgear a.c. and/or d.c. supplied to a.c. invertor including stabilizing elements for starting and operating one or more tubular fluorescent lamps, generally at high frequency 3.7 fluorescent lamp d
41、ischarge lamp of the low pressure mercury type, in which most of the light is emitted by one or several layers of phosphors excited by the ultra-violet radiation from the discharge 3.8 controlgear lamp circuit electrical circuit, or part thereof, normally built in a luminaire, consisting of the cont
42、rolgear and lamp(s) BS EN 62442-1:201162442-1 IEC:2011 7 3.9 reference ballast special ballast, either inductive for lamps for operation on a.c. mains frequencies, or resistive for lamps for operation on high frequency It is designed for the purpose of providing comparison standards for use in testi
43、ng ballasts, for the selection of reference lamps and for testing regular production lamps under standardized conditions. It is essentially characterized by the fact that, at its rated frequency, it has a stable voltage/current ratio which is relatively uninfluenced by variations in current, tempera
44、ture and magnetic surroundings, as outlined in IEC 60929. NOTE Annex B provides details of calculating the reference ballast characteristics and the method of operation with the reference ballast. 3.10 reference lamp lamp selected for testing controlgear which, when associated with a reference contr
45、olgear, has electrical characteristics which are close to the rated values or typical lamp characteristics as stated in the relevant lamp standard For details regarding the tolerances, see Clause B.2. 3.11 rated supply voltage of a controlgear voltage specified by the controlgear manufacturer for a
46、given controlgear that applies to a given operation condition 3.12 rated power of a lamp PLratedpower, expressed in watts, of a given lamp type specified by the manufacturer or the supplier, the lamp being operated under specified conditions 3.13 ballast lumen factor BLF ratio of the light output of
47、 the reference lamp when the ballast under test is operated at its rated voltage, compared with the light output of the same lamp operated with the appropriate reference ballast supplied at its rated voltage and frequency 3.14 total input power total power supplied to the controlgear lamp circuit me
48、asured at rated input voltage The rated power specified is related to a specific ballast lumen factor (BLF). 3.15 controlgear efficiency controlgearratio between the summation of the rated lamp power(s) and the corrected to reference conditions input power of the controlgear lamp circuit with possib
49、le sensors, network connections and other auxiliary loads disconnected 3.16 multi-lamp-power controlgear controlgear designed for the operation of one lamp which could have different lamp power 3.17 multi-number-lamp controlgear controlgear designed for the operation of more than one lamp BS EN 62442-1:2011 8 62442-1 IEC:2011 4 General 4.1 Applicability The measurement and calculation methods of this standard shall only be used for controlgear which confor
