1、CEN EN*IS0*45bb 95 M 3404589 0304324 873 BRITISH STANDARD Small craft with inboard M BS EN IS0 engine - Propeller shaft ends and bosses with 1:lO taper The European Standard EN IS0 4566 : 1995 has the status of a British Standard 4566 : 1995 CEN EN*IS0*45bb 95 3404589 0304325 70T under the authority
2、 of the Standards Board and comes into Amd. No. Date effect on 15 August 1995 0 BSI 1995 The following BSI references relate to the work on this standard: Committee reference GME133 Draft for comment 91!82889 DC ISBN O 580 24549 7 BS EN IS0 4566 : 1995 Text affected Committees responsible for this B
3、ritish Standard The preparation of this British Standard was entrusted to chnical Committee GMEl33, Small craft, upon which the following bodies were represented: Consumer Policy Committee of BSI Department of Trade and Industry Department of Trade and Industry (Standards Policy Unit) Federation of
4、Wire Rope Manufacturers of Great Britain Fire Extinguishing Trades Association Home Office Lloyds Register of Shipping Manne Safety Agency National Rivers Authority Personal Watercraft Association Royal Ocean Racing Club Royal Society for the Prevention of Accidents Royal Yachting Association Coopte
5、d Members British Canoe Manufacturers Association British Manne Industries Federation British Nautical Instrument Trade Association British Waterways Board CEN EN*IS0*45bb 95 U 3404589 010432b b4b BS EN IS0 4566 : 1995 Contents Committees responsible National foreword Page Inside front cover 11 Fore
6、word Specification 1 Scope 2 Normative references 3 Definitions 4 Dimensions 5 Construction details 6 %lerances 7 Threads 8 Designation 2 i CEN EN*IS0*4566 95 3404589 0304327 582 BS EN IS0 4566 : 1995 National foreword This British Standard has been prepared by Technical Committee GME/33 and is the
7、English language version of EN IS0 4566 : 1995 Small craft with inboard engine - Propeller shaft ends and bosses with 1:10 taper, published by the European Committee for Standardization (CEN). It is identical with IS0 4566 : 1992 published by the International Organization for Standardization (ISO).
8、 Cross-reference IS0 1947 : 1973 Publication referred to Corresponding British Standard BS 4500 IS0 limits and fits part 5 : 1988 Specification for system of cone tolerances for conical workpieces from C = 1:3 to 1:500 and lengths from 6 mm to 630 mm Compliance with a British Standard does not of it
9、self confer immunity from legal obligations. 11 CEN EV*IS0*4566 95 3404589 0304328 4L W EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 4566 April 1995 ICs 47.080 Supersedes EN 24566 : 1989 Descriptors: Shipbuilding, small craft, marine propellers, propeller shafts, shaft ends, hubs, dimens
10、ions, dimensional tolerances, designation English version Small craft with inboard engine - Propeller shaft ends and bosses with 1 : 10 taper (IS0 4566 : 1992) Navires de plaisance moteur intrier - Extrmits darbres porte-hlices et moyeux dhlices avec une conicit de 1 : 10 (IS0 4566 : 1992) Kleine Wa
11、sserfahrzeuge mit Innenbordmotoren - Propellerwellenenden und Propellernaben mit Kegel 1 : 10 (IS0 4566 : 1992) This European Standard was approved by CEN on 1994-10-25. CEN members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European
12、Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, Fre
13、nch, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland,
14、France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart, 36 B-1050 Brussel
15、s O 1995 All rights of reproduction and communication in any form and by any means reserved in all countries to CEN and its members. Ref. No. EN IS0 4566 : 1995 E CEN EN*ISO*45bb 95 3404589 0304329 355 Page 2 EN IS0 4566 : 1995 Foreword The text of the International Standard from ISO/X 188, Small cr
16、aft, of the International Organization for Standardization (ISO) has been taken over as a European Standard by CEN/CS. This European Standard supersedes EN 24566 : 1989. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsem
17、ent, at the latest by October 1995, and conflicting national standards shall be withdrawn at the latest by October 1995. According to the CENKENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greec
18、e, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom. CEN EN*ISO*45bb 95 D 3404589 0304330 077 D Page 3 EN IS0 4566 : 1995 Small craft with inboard engine - Propeller shaft ends and bosses with 1:lO taper 1 Scope This International Standar
19、d specifies the dimensions for interchangeability of propeller bosses (hubs) and propeller shaft ends in the shaft diameter range of 20 mm to 160 mm with a taper of 1 :1 O”, intended for installation on inboard-engined small craft. 2 Normative references The following standards contain provisions wh
20、ich, through reference in this text, constitute provisions of this International Standard. At the time of publi- cation, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibil
21、ity of applying the most re- cent editions of the standards indicated below. Members of IEC and IS0 maintain registers of cur- rent ly valid l nternat iona l Standards , ISO/R 773:1969, Rectangular or square parallel keys and their corresponding keyways (Dimensions in millime tres). IS0 1947: 1973,
22、System of cone tolerances for conical workpieces from C = 1:3 to 1.500 and lengths from 6 to 630 mm. 3 Definitions For the purposes of this International Standard, the following definitions apply. 3.1 nominal diameter: Diameter of the large end of the shaft end taper, which is the same as the di- am
23、eter of the cylindrical shaft, ignoring tolerances. 3.2 taper: Conical portion of the shaft end designed to accommodate a key to transmit the full propeller shaft torque to the propeller, while allowing for dis- assembly. 4 Dimensions The dimensions shall be those shown in figure1 and table 1. The “
24、reference dimensions” indicated in the table shall be considered nominal dimensions for guidance only. Configurations shown in figure 1 not specified by di- mensions in table 1 are not essential to interchange- ability and are therefore left to the discretion of the manufacturer. Nominal diameters w
25、ithout brackets shall be pre- ferred; those in brackets are a second choice. Thread diameters without brackets shall similarly be preferred; those in brackets are alternatives. 5 Construction details Details indicated in figure 1 are not intended to restrict design; nor are they to scale. Types and
26、methods of construction or machining of the key, the keyway and their corner radii, the thread undercut and the thread end, or of other optional details (.e. safety pin hole, centring point, etc.) are left open for individual meth- ods to comply with the configuration of the coupling and/or particul
27、ar needs. The length of the thread l2 shall be equal to thread diameter 4. The part of the thread engaged by the propeller nut shall be not less than 80 % of the thread length 12. 6 Tolerances 6.1 Shaft end taper small diameter, d, The tolerances shall be as given in table 1. The toler- ance deviati
28、ons are calculated from the nominal di- ameter. 1) IS0 8845 (to be published) will cover propeller shaft ends and bosses machined to a taper of 1 :I 6. 6.2 Boss taper large diameter, D The tolerances shall be as given in table 1 6.3 Cone angle The tolerances shall be cone diameter tolerances as in I
29、S0 1947 with tolerance ranges equal to the diam- eter tolerance ranges specified in 6.1 and 6.2 for di- ameters d, and D respectively. 6.4 Keyways and keys The tolerances shall be those given for normal keys in ISO/R 773. A-A 8 6.5 Boss length, Z, The tolerance shall be f 0,5 mm. 7 Threads Propeller
30、 nuts and shaft ends shall use M-Fine threads. 8 Designation Both propeller shafts and bosses constructed in ac cordance with these requirements shall be designated by a reference to this International Standard, and the nominal diameter. EXAMPLE Propeller boss IS0 4566 - 35 Forward face of propeller
31、 boss I“ i;) -.- i II )“I r !I ) t -i I I I I” NOTE - 12 (thread length) = 04 Patt of thread engaged by nut = 0.8 4 See clause 5. Figure 1 CEN EN*ISO*4566 95 m 3404589 0104332 94T m Page 5 EN IS0 4566 : 1995 Dimensions in millimetres Reference dimension11 4 - 15 17 19 22 26 30 34 38 42 46 50 54 57 6
32、1 65 69 73 77 85 93 1 o1 1 o9 117 125 - - - - - - - Table 1 Shaft end taper Small diameter Thread Diameter Pitch Nominal diameter Dmm Key Width b 6 6 8 8 10 12 14 14 16 18 18 20 20 22 22 25 25 28 28 32 32 36 36 40 Boss Bore bigger diameter Depth h 6 6 7 7 8 8 9 9 10 11 11 12 12 14 14 14 14 16 16 18
33、18 20 20 22 15 45 45 55 75 85 95 105 115 120 130 140 150 165 175 185 190 200 215 235 255 275 295 315 335 c b 5 o 5 o 5 o 5 o 5 o 5 o 5 O 5 O 10 o 10 O 10 O 10 O 10 5 10 5 10 5 15 5 15 5 15 10 15 10 15 10 15 10 15 10 15 10 15 10 38,438 I 36 (30) I 3 I 40 I 45 75,000 78,500 86,500 74,913 64 (56) 4 78,
34、413 72 (64) 4 86,413 80 (72) 4 70 80 85 75 85 90 Length 4 max 7 min. min max 20 22 25 30 20,000 22,000 25,000 30,000 20,052 22,052 25,052 30,052 50 50 60 80 90 1 O0 110 35 40 45 35,000 40,000 45,000 35,062 40,062 45,062 50 (55) 60 120 130 140 50,000 55,000 60,000 65,000 70,000 74,500 50,062 55,074 6
35、0,074 65,074 70,074 74,574 38,500 43,000 47,000 51,000 55,000 58,500 36 42 40 50 50 55 55 - 42,926 46,926 50,926 54,926 58,426 42 48 48 (651 70 (75) 80 (85) 90 150 160 170 180 190 200 79,500 84,500 89.500 79,574 84,587 89,587 62,500 66,500 71,000 62,426 66,413 70,913 56 64 (56) (95) 1 O0 110 94,587
36、99,087 109,087 21 o 220 240 260 280 300 94,500 99,000 109,000 1 19,000 129,O 139.0 120 130 140 119,087 129,l 139.1 1 94,413 94,500 1 90 (80) 1 i 102,500 102,413 100 (90) 110,500 710.413 100 (90) 118,500 118,413 110 (1001 90 1 O0 1 O0 320 340 149.0 159.0 - 149.1 159,l 110 150 160 1 For guidance only.
37、 see clause 4 CEN EN*IS0*45bb 75 M 3404589 0304333 886 D BS EN IS0 4566 : 1995 List of references Sec national foreword. CEN EN*IS0*45bb 75 3404589 0104334 712 BS EN IS0 4566 : 1995 BSI 389 Chiswick High Road London W4 4AL 9508- 5- 0.35k- FP BSI - British Standards Institution BSI is the independent
38、 national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Contract requirements A British Standard does not purport to include all the necessary provisions of a contract. Users of Br
39、itish Standards are responsible for their correct application. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. Any person who finds an inaccuracy or ambiguity while using this British S
40、tandard should bring it to the attention of the Quality Manager, BSI without delay so that the matter may be investigated swiftly. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Ord
41、ers for all BSI, international and foreign standards publications should be addressed to Customer Services, Sales Department at Chiswick: Tel: 0181 996 7000; Fax: O181 996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have be
42、en published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library, the Standardline Database, the BSI Information Rchnology Service (BITS) and its Rchnical Help to Exp
43、orters Service. Contact the Information Department at Chiswick: Tel: O181 996 7111; Fax: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Cus
44、tomer Services, Membership at Chiswick: Bl: O181 996 7002; Fax: 0181 996 7001. Copyright Copyright subsists in all BSI publications and no part may be reproduced in any form without the prior permission in writing of BSI. This does not preclude the free use, in the course of implementing the standar
45、d of necessary details such as symbols and size, type or grade designations including use by incorporation into computer programs, but where these details are reproduced including without limitation in printed form, in computer programs or in any other form whatsoever, the permission in writing of BSI must be obtained and if granted will be on terms including royalty, before the product is sold, licensed or otherwise exploited for commercial gain. Enquiries about copyright should be made to the Copyright Manager at Chiswick. SBN O 580 24549 7 Product code 00559522
