1、Rubber hoses and hose assemblies for use in oil burners - Specification (ISO 6806:2017)BS EN ISO 6806:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 6806 June 2017 ICS 83.140.40; 27.060.10 Supersedes EN IS
2、O 6806:2014English Version Rubber hoses and hose assemblies for use in oil burners - Specification (ISO 6806:2017) Tuyaux et flexibles en caoutchouc pour brleurs fuel -Spcifications (ISO 6806:2017) Gummischluche und Schlauchleitungen fr den Einsatz in lbrennern - Anforderung (ISO 6806:2017)This Euro
3、pean Standard was approved by CEN on 3 February 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references c
4、oncerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member
5、 into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, Franc
6、e, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPIS
7、CHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 6806:2017 ENational forewordThis British Standard is the UK implementation of EN ISO
8、6806:2017. It is identical to ISO 6806:2017. It supersedes BS EN ISO 6806:2014, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/66, Rubber and plastics tubing, hoses and hose assemblies.A list of organizations represented on this committee can be o
9、btained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 89075 8ICS 27.060.10; 83.140.40
10、Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 6806:201
11、7EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 6806 June 2017 ICS 83.140.40; 27.060.10 Supersedes EN ISO 6806:2014English Version Rubber hoses and hose assemblies for use in oil burners - Specification (ISO 6806:2017) Tuyaux et flexibles en caoutchouc pour brleurs fuel -Spcifications (ISO
12、 6806:2017) Gummischluche und Schlauchleitungen fr den Einsatz in lbrennern - Anforderung (ISO 6806:2017)This European Standard was approved by CEN on 3 February 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European St
13、andard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (Engl
14、ish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium,
15、Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Swi
16、tzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN natio
17、nal Members. Ref. No. EN ISO 6806:2017 EBS EN ISO 6806:2017EN ISO 6806:2017 (E) 3 European foreword This document (EN ISO 6806:2017) has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber products“ in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses and hos
18、e assemblies” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2017, and conflicting national standards shall be withdrawn at the latest by Decembe
19、r 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 6806:2014. According to the CEN-CENELEC Internal Regulations,
20、 the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, La
21、tvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 6806:2017 has been approved by CEN as EN ISO 6806:2017 without any modification. ISO 6806:2017
22、(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a
23、 technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matte
24、rs of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This docu
25、ment was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all
26、 such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users a
27、nd does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to
28、 Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Rubber and plastics hoses and hose assemblies.This fourth edition cancels and replaces the third edition (ISO 6806:2014),
29、 which has been technically revised with the following changes: Table 3 has been amended; Clause 10 has been amended.iv ISO 2017 All rights reservedBS EN ISO 6806:2017ISO 6806:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodi
30、es (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations
31、, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further m
32、aintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives
33、).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Intro
34、duction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specif
35、ic terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee
36、 ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Rubber and plastics hoses and hose assemblies.This fourth edition cancels and replaces the third edition (ISO 6806:2014), which has been technically revised with the following changes: Table 3 has been amended; Clause 10 has been amended.iv
37、ISO 2017 All rights reservedBS EN ISO 6806:2017INTERNATIONAL STANDARD ISO 6806:2017(E)Rubber hoses and hose assemblies for use in oil burners Specification1 ScopeThis document specifies the minimum requirements for rubber hoses and hose assemblies for use in oil burners.The following two types of ho
38、se assembly are specified. Type 1: Hose assemblies for flux and reflux, but not for insertion between the oil burner pump and the atomizing connection; maximum working pressure 1,0 MPa (10 bar); maximum oil temperature 100 C. Type 2: Hose assemblies for insertion between the oil burner pump and the
39、atomizing connection; maximum working pressure 4,0 MPa (40 bar); maximum oil temperature 100 C.The hose assemblies specified in this document are not intended to be used, without special assessment, for purposes other than oil burner installations.2 Normative referencesThe following documents are re
40、ferred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 48, Rubber, vulcanized o
41、r thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD)ISO 1307, Rubber and plastics hoses Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hosesISO 1402, Rubber and plastics hoses and hose assemblies Hydrostatic testingISO 1436, Rubber hose
42、s and hose assemblies Wire-braid-reinforced hydraulic types for oil-based or water-based fluids SpecificationISO 1817, Rubber, vulcanized or thermoplastic Determination of the effect of liquidsISO 4671, Rubber and plastics hoses and hose assemblies Methods of measurement of the dimensions of hoses a
43、nd the lengths of hose assembliesISO 7326, Rubber and plastics hoses Assessment of ozone resistance under static conditionsISO 8330, Rubber and plastics hoses and hose assemblies VocabularyISO 10619-2:2011, Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 2: Bending
44、 tests at sub-ambient temperatures3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 8330 apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at h t t p :/ www .electroped
45、ia .org/ ISO 2017 All rights reserved 1BS EN ISO 6806:2017INTERNATIONAL STANDARD ISO 6806:2017(E)Rubber hoses and hose assemblies for use in oil burners Specification1 ScopeThis document specifies the minimum requirements for rubber hoses and hose assemblies for use in oil burners.The following two
46、types of hose assembly are specified. Type 1: Hose assemblies for flux and reflux, but not for insertion between the oil burner pump and the atomizing connection; maximum working pressure 1,0 MPa (10 bar); maximum oil temperature 100 C. Type 2: Hose assemblies for insertion between the oil burner pu
47、mp and the atomizing connection; maximum working pressure 4,0 MPa (40 bar); maximum oil temperature 100 C.The hose assemblies specified in this document are not intended to be used, without special assessment, for purposes other than oil burner installations.2 Normative referencesThe following docum
48、ents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 48, Rubber, v
49、ulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD)ISO 1307, Rubber and plastics hoses Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hosesISO 1402, Rubber and plastics hoses and hose assemblies Hydrostatic testingISO 1436, Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types for oil-based or water-based fluids SpecificationISO 1817, Rubber, vulcanized or thermoplastic Determination of the effect of liqu
