1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 7049:2011Cross-recessed pan head tapping screws(ISO 7049:2011)BS EN ISO 7049:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN
2、ISO 7049:2011.It supersedes BS EN ISO 7049:1995 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee FME/9/3, Fasteners - Product Standards.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does
3、 not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 68777 8ICS 21.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of t
4、heStandards Policy and Strategy Committee on 31 August 2011.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 7049 August 2011 ICS 21.060.10 Supersedes EN ISO 7049:1994English Version Cross-recessed pan head tapping screws (ISO 7049:2011) V
5、is tle tte cylindrique bombe large empreinte cruciforme (ISO 7049:2011) Linsenkopf-Blechschrauben mit Kreuzschlitz (ISO 7049:2011) This European Standard was approved by CEN on 1 July 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for g
6、iving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three o
7、fficial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies
8、 of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingd
9、om. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 7049:2011: EBS E
10、N ISO 7049:2011EN ISO 7049:2011 (E) 3 Foreword This document (EN ISO 7049:2011) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be given the status of
11、a national standard, either by publication of an identical text or by endorsement, at the latest by February 2012, and conflicting national standards shall be withdrawn at the latest by February 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject
12、 of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 7049:1994. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this
13、 European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland
14、and the United Kingdom. Endorsement notice The text of ISO 7049:2011 has been approved by CEN as a EN ISO 7049:2011 without any modification. BS EN ISO 7049:2011ISO 7049:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federatio
15、n of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.
16、 International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance wi
17、th the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires appro
18、val by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 7049 was prepared by Technical Committe
19、e ISO/TC 2, Fasteners, Subcommittee SC 13, Fasteners with non-metric thread. This second edition cancels and replaces the first edition (ISO 7049:1983), which has been technically revised. BS EN ISO 7049:2011BS EN ISO 7049:2011INTERNATIONAL STANDARD ISO 7049:2011(E) ISO 2011 All rights reserved 1Cro
20、ss-recessed pan head tapping screws 1 Scope This International Standard specifies the characteristics of cross-recessed pan head tapping screws with thread sizes from ST 2,2 to ST 9,5 inclusive. 2 Normative references The following referenced documents are indispensable for the application of this d
21、ocument. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions ISO 1478, Tapping screws thread ISO 2702, H
22、eat-treated steel tapping screws Mechanical properties ISO 3269, Fasteners Acceptance inspection ISO 3506-4, Mechanical properties of corrosion-resistant stainless steel fasteners Part 4: Tapping screws ISO 4042, Fasteners Electroplated coatings ISO 4757, Cross recesses for screws ISO 4759-1, Tolera
23、nces for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings ISO 16048, Passivation of corrosion-resistant stainless-steel fasteners
24、BS EN ISO 7049:2011ISO 7049:2011(E) 2 ISO 2011 All rights reserved3 Dimensions See Figure 1 and Table 1. Symbols and descriptions of dimensions are specified in ISO 225. a) Type C b) Type F c) Type R d) Type H Cross recess e) Type Z Cross recess aDimension a shall be measured at the core diameter of
25、 the first full thread. Figure 1 Cross-recessed pan head tapping screw BS EN ISO 7049:2011ISO 7049:2011(E) ISO 2011 All rights reserved 3Table 1 Dimensions Dimensions in millimetres Thread size ST 2,2 ST 2,9 ST 3,5 ST 4,2 ST 4,8 ST 5,5 ST 6,3 ST 8 ST 9,5 Pa0,8 1,1 1,3 1,4 1,6 1,8 1,8 2,1 2,1 a max.
26、0,8 1,1 1,3 1,4 1,6 1,8 1,8 2,1 2,1 damax. 2,8 3,5 4,1 4,9 5,6 6,3 7,3 9,2 10,7 max. 4,00 5,60 7,00 8,00 9,50 11,00 12,00 16,00 20,00 dkmin. 3,70 5,30 6,64 7,64 9,14 10,57 11,57 15,57 19,48 max. 1,60 2,40 2,60 3,10 3,70 4,00 4,60 6,00 7,50 k min. 1,40 2,15 2,35 2,80 3,40 3,70 4,30 5,60 7,10 r min. 0
27、,10 0,10 0,10 0,20 0,20 0,25 0,25 0,40 0,40 rf 3,2 5,0 6,0 6,5 8,0 9,0 10,0 13,0 16,0 Recess No 0 1 2 3 4 m ref. 1,9 3,0 3,9 4,4 4,9 6,4 6,9 9,0 10,1 max. 1,20 1,80 1,90 2,40 2,90 3,10 3,60 4,70 5,80 Type H Penetration min. 0,85 1,40 1,40 1,90 2,40 2,60 3,10 4,15 5,20 m ref. 2,0 3,0 4,0 4,4 4,8 6,2
28、6,8 8,9 10,1 max. 1,20 1,75 1,90 2,35 2,75 3,00 3,50 4,50 5,70 Cross recess Type Z Penetration min. 0,95 1,45 1,50 1,95 2,30 2,55 3,05 4,05 5,25 Type C 2,0 2,6 3,2 3,7 4,3 5,0 6,0 7,5 8,0 Type F 1,6 2,1 2,5 2,8 3,2 3,6 3,6 4,2 4,2 y ref. Type R 2,7 3,2 3,6 4,3 5,0 6,3 lbType C and Type R Type F nom.
29、 min. max. min. max. 4,5 3,7 5,3 3,7 4,5 6,5 5,7 7,3 5,7 6,5 9,5 8,7 10,3 8,7 9,5 13 12,2 13,8 12,2 13,0 Range 16 15,2 16,8 15,2 16,0 of 19 18,2 19,8 18,2 19,0 preferred 22 21,2 22,8 20,7 22,0 lengths 25 24,2 25,8 23,7 25,0 32 30,7 33,3 30,7 32,0 38 36,7 39,3 36,7 38,0 45 43,7 46,3 43,5 45,0 50 48,7
30、 51,3 48,5 50,0 aP = pitch of the thread. bSizes with lengths marked with a dash () cannot be manufactured. BS EN ISO 7049:2011ISO 7049:2011(E) 4 ISO 2011 All rights reserved4 Specifications and reference International Standards See Table 2. Table 2 Specifications and reference International Standar
31、ds Material Steel, in accordance with ISO 2702 Stainless steel General requirements ISO 8992 Thread ISO 1478 Cross recess ISO 4757 Steel grade/ hardness class A2-20H, A4-20H, A5-20H Mechanical propertyInternational Standard ISO 2702 ISO 3506-4 Product grade A Tolerances International Standard ISO 47
32、59-1 As processed Finish Coating Requirements for electroplating are specified in ISO 4042. Requirements for non-electrolytically applied zinc flake coatings are specified in ISO 10683. Additional requirements or other finishes or coatings shall be agreed between the supplier and the purchaser. Requ
33、irements for passivation are specified in ISO 16048. Acceptability Acceptance inspection is specified in ISO 3269. 5 Designation EXAMPLE 1 A cross-recessed pan head tapping screw with thread size ST 3,5, nominal length l = 16 mm, made of steel (St) in accordance with ISO 2702, rounded end (Type R) a
34、nd cross recess Type Z is designated as follows: Tapping screw ISO 7049 - ST 3,5 16 - St - R - Z EXAMPLE 2 A cross-recessed pan head tapping screw with thread size ST 3,5, nominal length l = 16 mm, made of stainless steel (A4-20H) in accordance with ISO 3506-4, rounded end (Type R) and cross recess
35、Type H is designated as follows: Tapping screw ISO 7049 - ST 3,5 16 - A4-20H - R - H BS EN ISO 7049:2011This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, informat
36、ion and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 S
37、tandards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileu
38、sing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers auto
39、matically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standard
40、s publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Inform
41、ation on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and se
42、rvices. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996
43、7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications
44、of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission
45、from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email:
