1、BSENISO10350-1:2008ICS 83.080.20,NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISHSTANDARDPlasticsAcquisitionandpresentationofcomparablesingle-pointdataPart1:Mouldingmaterials(ISO10350-1:2007)+A1:2014National forewordThis British Standard is the UK implementation of EN IS
2、O 10350-1:2008+A1:2014. It is identical to ISO 10350-1:2008, incorporating amendment 1:2014. It supersedes BS EN ISO 10350-1:2008 which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to ISO text carry the number
3、of the ISO amendment. For example, text altered by ISO amendment 1 is indicated by !“.The UK participation in its preparation was entrusted to Technical Committee PRI/21, Testing of plastics.A list of organizations represented on this committee can be obtained on request to its secretary.This public
4、ation does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.BS EN ISO 10350-1:2008+A1:2014This British Standardwas published under theauthority of theS
5、tandards Policy andStrategy Committee on31 December 2008Amendments/corrigenda issued since publicationDate Comments 31 August 2014 Implementation of ISO amendment 1:2014 with CEN endorsement A1:2014ISBN 978 0 580 74926 1 The British Standards Institution 2014. Published by BSI Standards Limited 2014
6、EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 10350-1:2008+A1ICS 83.080.20English VersionPlastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2007)Plastiques - Acquisition et prsentation de caractristiquesintrinsques comparables -
7、Partie 1: Matriaux pourmoulage (ISO 10350-1:2007)Kunststoffe - Ermittlung und Darstellung vergleichbarerEinpunktkennwerte - Teil 1: Formmassen (ISO 10350-1:2007)This European Standard was approved by CEN on 30 July 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
8、stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standar
9、d exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standard
10、s bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
11、EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 10350-1:2008: EJune 201
12、43 Foreword The text of ISO 10350-1:2007 has been prepared by Technical Committee ISO/TC 61 “Plastics” of theInternational Organization for Standardization (ISO) and has been taken over as EN ISO 10350-1:2008 byTechnical Committee CEN/TC 249 “Plas tics” the secretariat of which is he ld by NBN. This
13、 European Standard shall be given the status ofa national standard, either by publication of an identical text or byendorsement, at the latest by February2009, and conflicting national standards shall be withdrawnat the latest by February 2009. Attention is drawn to the possibility that some of the
14、elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any orall such patent rights. This document supersedes EN ISO 10350-1:2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the f
15、ollowingcountries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, CzechRepublic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, S lovakia, Sl
16、ovenia, Spain, Sweden, Switzerland and the UnitedKingdom. Endorsement noticeThe text of ISO 10350-1:2007 has been approved by CEN as a EN ISO 10350-1:2008 without anymodification. This document (EN ISO 10350-1:2008/A1:2014) has been prepared by Technical Committee ISO/TC 61 “Plastics” in collaborati
17、on with Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by NBN. This Amendment to the European Standard EN ISO 10350:2008 shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2014, and co
18、nflicting national standards shall be withdrawn at the latest by December 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. Accord
19、ing to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
20、Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 10350-1:2008/Amd 1:2014 has been approved by CEN as EN ISO
21、 10350-1:2008/A1:2014 without any modification. Foreword to amendment A1BS EN ISO 10350-1:2008+A1:2014 EN ISO 10350-1:2008+A1:2014 (E) ISO 2007 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope .12 Normative references. 13 Terms and definitions. 34 Specimen preparation and conditi
22、oning 35 Test requirements.46 Presentation of results.4BS EN ISO 10350-1:2008+A1:2014 ISO 10350-1:2007+A1:2014 (E)iv ISO 2007 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of p
23、reparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a tec hnical committee has beenestablished has the right to be represented on that committee. International organizations, governmental and non-governmental,
24、in liaison with ISO, also take part in the work. ISO collaborates closelywith the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordancewith the rules given in the ISO/IEC Directives, Part 2.The main task
25、of technical committees is to prepare International Standards. Draft International Standardsadopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval byat least 75 % of the member bodies casting a vote. Attention is
26、 drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO10350-1 wasprepared by Technical Committee ISO/TC61, Plastics, Subcommittee SC 2, Mechanical properties. This
27、second edition cancels and replaces the first edition (ISO10350-1:1998), which has been technically revised.ISO10350 consists of the following parts, under the general title Plastics Acquisitionand presentation of comparable single-point data : Part 1:Moulding materials Part 2: Long-fibre-reinforced
28、 plasticsBS EN ISO 10350-1:2008+A1:2014 ISO 10350-1:2007+A1:2014 (E) ISO 2007 All rights reserved vIntroduction ISO10350 has been prepared because users of plastics find that available data cannot always be readily used to compare the properties of similar materials, especiallywhen the data have bee
29、n supplied by differentsources. Evenwhen the same standard tests have been used, they often allowthe adoption of a wide rangeof alternative test conditions, and the data obtained are not necessarily comparable. The purpose of thisInternational Standard is to identify s pecific methods and conditions
30、 of test to be used for the acquisition andpresentation of data in order that valid comparisons between materials can be made. ISO10350 is concerned with tests employed to present “single-point” data on the limited range of propertiescommonly included in data sheets and used for the preliminary sele
31、ction ofmaterials. Suchdata represent the most basic approach to the specification of properties ofmaterials, and the standard thus facilitates the firststeps towards more efficient selection and use of plastics in the manyapplications to which they are suited. Complementary International Standards
32、(ISO11403-1, ISO11403-2 and ISO 11403-3)1 ) are concernedwiththe standardized acquisition and presentation of multipoint data, to demonstrate how properties varywithimportant factors such as time, temperature and the presence of particular natural and chemical environments.In these standards, some a
33、dditional properties are included. Their use will provide a more substantialdatabase than one containing only single-point data, and so will enable improved assessment of the fitness of a material for any particular application. In addition, ISO11403-1, which deals with mechanical properties, assist
34、s predictions of the performance of components and ISO 11403-2, co vering thermal and processingproperties, aids predictions of melt-flow behaviour during manufacturing. ISO 11403-3 is concerned withenvironmental influences on properties, and other partsmaybe prepared to cover additional properties.
35、 1 ) ISO11403-1, Plastics Acquisition and presentation of comparable multipoint data Part 1: Mechanical propertiesISO11403-2, Plastics Acquisition and presentation of comparable multipoint data Part 2: Thermal andprocessing propertiesISO11403-3, Plastics Acquisition and presentation of comparable mu
36、ltipoint data Part3: Environmentalinfluences on propertiesBS EN ISO 10350-1:2008+A1:2014 ISO 10350-1:2007+A1:2014 (E)BS EN ISO 10350-1:2008+A1:2014 ISO 10350-1:2007+A1:2014 (E)INTERNATIONAL STANDA RD ISO 2007 All rights reserved 1Plastics Acquisition and presentation of comparable single-point dataP
37、art 1: Moulding materials 1 Scope ISO10350 identifies specific test procedures for the acquisition and presentation of comparable data forcertain basic properties of plastics. In general, each property is specified by a single experimental value,although in certain cases properties are represented b
38、ytwo values obtained under different test conditions. The properties included are those presented conventionally in manufacturers data sheets. This part of ISO10350 applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials that may be injection- or compression-mo
39、ulded or prepared as sheets of specified thickness. Part2 of ISO10350 deals specificallywith long- or continuous-fibre-reinforced plastics. For the purposes of ISO10350, long-fibre-reinforced plastics are considered to have fibre lengths greater than 7,5 mm prior to moulding. 2 NormativereferencesTh
40、e following referenced documents are indispensable for the application of this document. For datedreferences, only the edition cited applies. For undated references, the latest edition of the referenceddocument (including anyamendments) applies.ISO 62, Plastics Determination of water absorptionISO 7
41、5-1, Plastics Determination of temperature of deflection under load Part 1: General test methodISO 75-2, Plastics Determination of temperature of deflection under load Part 2: Plastics and eboniteISO 178, Plastics Determination of flexural propertiesISO 179-1, Plastics Determination of Charpy impact
42、 properties Part1: Non-instrumented impact testISO 179-2, Plastics Determination of Charpy impact properties Part2: Instrumented impact testISO 291, Plastics Standard atmospheres for conditioning and testingISO 293, Plastics Compression moulding of test specimens of thermoplastic materialsISO 294-1,
43、 Plastics Injection mouldingoftestspecimens of thermoplastic materials Part1:Generalprinciples, and mouldingof multipurpose and bar testspecimensISO 294-3, Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small platesISO 294-4, Plastics Injection moulding of test spec
44、imens of thermoplastic materials Part4:Determination of mouldingshrinkageISO 295, Plastics Compression moulding of test specimens of thermosetting materialsBS EN ISO 10350-1:2008+A1:2014 ISO 10350-1:2007+A1:2014 (E)2 ISO 2007 All rights reservedISO 306, Plastics Thermoplastic materials Determination
45、 of Vicat softening temperature (VST)ISO 527-1, Plastics Determination of tensile properties Part 1: General principlesISO 527-2, Plastics Determination of tensile properties Part2: Test conditions for moulding and extrusion plasticsISO 899-1, Plastics Determination of creep behaviour Part 1: Tensil
46、e creepISO 1133, Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplasticsISO 1183-1, Plastics Methods for determining the density of non-cellular plastics Part1: Immers ionmethod, liquid pyknometer method and titration methodISO 1183-2, Plastics M
47、ethods for determining the density of non-cellular plastics Part2: Density gradient column methodISO 1183-3, Plastics Methods for determining the density of non-cellular plastics Part3: Gas pyknometer methodISO 2577, Plastics Thermosetting moulding materials Determination of shri nkageISO 2818, Plas
48、tics Preparation of test specimens by machiningISO 4589-2, Plastics Determination of burning behaviour by oxygen index Part2: Ambient-temperaturetestISO 6603-2, Plastics Determination of punctureimpact behaviour of rigid plastics Part2: Instrumentedimpact testingISO 8256, Plastics Determination of t
49、ensile-impact strengthISO 10724-1, Plastics Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) Part 1: General principles and moulding of multipurpose test specimensISO 10724-2, Plastics Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) Part 2: Small platesISO 11357-2, Plastics Differential scanning calorimetry (DSC) Part2: Determination of glass transitiontemperatureISO 11357
