1、BRITISH STANDARD CONFIRMED DECEMBER 1998 BS EN ISO 11126-8:1998 BS 7079-F8: 1994 Incorporating Amendment No. 1 to BS 7079-F8:1994 (which is renumbers as BS EN ISO 11126-8:1998) Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cle
2、aning abrasives Part 8: Olivine sand The European Standard EN ISO 11126-8:1997 has the status of a British Standard ICS 87.020BSENISO11126-8:1998 This British Standard, having been prepared under the direction of the Surface Treatments and Coatings Standards Policy Committee, was published under the
3、 authority of the Standards Board and comes into effect on 15 March 1994 BSI 04-1999 The following BSI references relate to the work on this standard: Committee reference STC/21 Draft for comment 92/50246 DC ISBN 0 580 23058 9 Committees responsible for this British Standard The preparation of this
4、British Standard was entrusted by the Surface Treatments and Coatings Standards Policy Committee (STC/-) to Technical Committee STC/21, upon which the following bodies were represented: Association of Consulting Engineers British Chemical Engineering Contractors Association British Coatings Federati
5、on Ltd. British Constructional Steelwork Association Ltd. British Grit Association British Railways Board British Steel Industry Department of Transport Electricity Association Institute of Corrosion National Federation of Painting and Decorating Contractors Oil and Colour Chemists Association Paint
6、 Research Association Royal Society of Chemistry Amendments issued since publication Amd. No. Date Comments 9845 February 1998 Renumbers BS 7079-F8:1994 as BS EN ISO 11126-8:1998, with addition of ENISO title page, foreword and Annex ZA, and changes to national foreword (indicated by sidelines in th
7、e margin)BSENISO11126-8:1998 BSI 04-1999 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN ISO 11126-8 3BSENISO11126-8:1998 ii BSI 04-1999 National foreword This British Standard has been prepared by Technical CommitteeSTI/21 and is the English lang
8、uage version of EN ISO11126-8:1997 Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part8: Olivine sand, published by the European Committee for Standardization (CEN). It is identical with ISO11126-8:1993, publ
9、ished by the International Organization for Standardization (ISO). International Standard ISO11126-8 was prepared by Technical Committee ISO/TC35, Paints and varnishes, Subcommittee SC12, Preparation of steel substrates before application of paints and related products. Cross-references The British
10、Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British St
11、andard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cove
12、r, an inside front cover, pagesi andii, theENISO title page, pages2to4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME
13、 EUROPENNE EUROPISCHE NORM EN ISO 11126-8 July 1997 ICS 87.020 Descriptors: Paints, varnishes, substrates, steel products, blast-cleaning, abrasives, non-metallic abrasives, specifications. English version Preparation of steel substrates before application of paints and related products Specificatio
14、ns for non-metallic blast-cleaning abrasives Part8: Olivine sand (ISO 11126-8:1993) Prparation des subjectiles dacier avant application de peintures et de produits assimils Spcifications pour abrasifs non mtalliques destins la prparation par projection Partie8: Sable lolivine (ISO 11126-8:1993) Vorb
15、ereitung von Stahloberflchen vor dem Auftragen von Beschichtungsstoffen Anforderungen an nichtmetallische Strahlmittel Teil 8: Olivinsand (ISO 11126-8:1993) This European Standard was approved by CEN on1997-06-16. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipul
16、ate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exi
17、sts in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bo
18、dies of Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Norm
19、ung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref. No. EN ISO 11126-8:1997 EENISO11126-8:1997 BSI 04-1999 2 Foreword The text of the International Standard from Technical Commi
20、ttee ISO/TC35, Paints and varnishes, of the International Organization for Standardization (ISO) has been taken over as a European Standard by Technical Committee CEN/TC139, Paints and varnishes, the secretariat of which is held by DIN. This European Standard shall be given the status of a national
21、standard, either by publication of an identical text or by endorsement, at the latest by January1998, and conflicting national standards shall be withdrawn at the latest by January1998. According to CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are
22、 bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. NOTENormative references to International Standards are liste
23、d in Annex ZA (normative). Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Definition 3 4 Designation of abrasives 3 5 Sampling 4 6 Requirements 4 7 Identification and marking 4 8 Information to be supplied by the manufacturer or supplier 4 Annex A (informative) Bibliography Inside bac
24、k cover Annex ZA (normative) Normative references to international publications with their relevant European publications Inside back cover Table 1 Particle size distribution 4 Table 2 Particular requirements for olivine sand abrasives 4ENISO11126-8:1993(E) BSI 04-1999 3 ENISO11126-8:1993(E) WARNING
25、 Equipment, materials and abrasives used for surface preparation can be hazardous if used carelessly. Many national regulations exist for those materials and abrasives that are considered to be hazardous during or after use (waste management), such as free silica or carcinogenic or toxic substances.
26、 These regulations are therefore to be observed. It is important to ensure that adequate instructions are given and that all required precautions are exercised. 1 Scope This part of ISO11126 specifies requirements for olivine sand abrasives, as supplied for blast-cleaning processes. It specifies ran
27、ges of particle sizes and values for apparent density, Mohs hardness, moisture content, conductivity of aqueous extract and water-soluble chlorides. The requirements specified in this part of ISO11126 apply to abrasives supplied in the “new” condition only. They do not apply to abrasives either duri
28、ng or after use. Test methods for non-metallic blast-cleaning abrasives are given in the various parts of ISO11127. NOTE 1Information on commonly referenced national standards for non-metallic abrasives is given in Annex A. NOTE 2Although this part of ISO11126 has been developed specifically to meet
29、 requirements for preparation of steelwork, the properties specified will generally be appropriate for use when preparing other material surfaces, or components, using blast-cleaning techniques. These techniques are described in ISO8504-2:1992, Preparation of steel substrates before application of p
30、aints and related products Surface preparation methods Part2: Abrasive blast-cleaning. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO11126. At the time of publication, the editions indicated were vali
31、d. All standards are subject to revision, and parties to agreements based on this part of ISO11126 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards
32、. ISO 11127-1:1993, Preparation of steel substrates before application of paints and related products Test methods for non-metallic blast-cleaning abrasives Part1: Sampling. ISO 11127-2:1993, Preparation of steel substrates before application of paints and related products Test methods for non-metal
33、lic blast-cleaning abrasives Part2: Determination of particle size distribution. ISO 11127-3:1993, Preparation of steel substrates before application of paints and related products Test methods for non-metallic blast-cleaning abrasives Part3: Determination of apparent density. ISO 11127-4:1993, Prep
34、aration of steel substrates before application of paints and related products Test methods for non-metallic blast-cleaning abrasives Part4: Assessment of hardness by a glass slide test. ISO 11127-5:1993, Preparation of steel substrates before application of paints and related products Test methods f
35、or non-metallic blast-cleaning abrasives Part5: Determination of moisture. ISO 11127-6:1993, Preparation of steel substrates before application of paints and related products Test methods for non-metallic blast-cleaning abrasives Part6: Determination of water-soluble contaminants by conductivity mea
36、surement. ISO 11127-7:1993, Preparation of steel substrates before application of paints and related products Test methods for non-metallic blast-cleaning abrasives Part7: Determination of water-soluble chlorides. 3 Definition For the purposes of this part of ISO11126, the following definition appli
37、es. 3.1 olivine sand a material manufactured from the naturally occurring mineral olivine which is crushed by a mechanical process, dried and sieved and prepared for use as a blast-cleaning abrasive NOTE 3Olivine is a magnesium/iron silicate with the chemical formula MgOSiO 2 Fe 2 O 3 . 4 Designatio
38、n of abrasives Olivine sand abrasives shall be identified by “Abrasive ISO11126” and the abbreviation N/OL indicating non-metallic, olivine sand abrasive. This shall be followed, without spaces, by an oblique stroke and then by the symbol G to indicate the required particle shape of the abrasive, wh
39、en purchased, as grit. The designation shall be completed by numbers denoting the particle size range, in millimetres, required (seeTable 1). EXAMPLE 1 Abrasive ISO 11126 N/OL/G 0,2-0,5 denotes an abrasive of the non-metallic olivine sand type, complying with the requirements of this part of ISO1112
40、6, of initial particle shape grit and particle size range0,2mm to0,5mm.ENISO11126-8:1993(E) 4 BSI 04-1999 It is essential that this full product designation is quoted on all orders. 5 Sampling Sampling procedures shall be as specified in ISO11127-1. 6 Requirements 6.1 General requirements The materi
41、al shall be free from corrosive constituents and adhesion-impairing contaminants. Foreign, harmful impurities shall not be permitted. 6.2 Particular requirements Particular requirements for olivine sand abrasives shall be as specified inTable 2. 7 Identification and marking All supplies shall be cle
42、arly marked or identified using the appropriate designation as specified in clause4, either directly or by the accompanying delivery note. 8 Information to be supplied by the manufacturer or supplier The manufacturer or supplier shall supply, if requested, a test report detailing results for any rel
43、evant property as determined by the appropriate method specified inTable 2. Table 1 Particle size distribution Table 2 Particular requirements for olivine sand abrasives Particle size range a mm 0,2 to 0,5 0,2 to 1 0,2 to 1,4 0,2 to 2 0,2 to 2,8 0,5 to 1 0,5 to 1,4 1,0 to 2 1,4 to 2,8 Oversize Sieve
44、 size mm 0,5 1 1,4 2 2,8 1 1,4 2 2,8 Residue %(m/m) max. 10 10 10 10 10 10 10 10 10 Nominal size Sieve size mm 0,2 0,2 0,2 0,2 0,2 0,5 0,5 1 1,4 Residue %(m/m) min. 85 85 85 85 85 80 80 80 80 Undersize Sieve size mm 0,2 0,2 0,2 0,2 0,2 0,5 0,5 1 1,4 Through-flow % (m/m) max 5 5 5 5 5 10 10 10 10 a B
45、y agreement between the interested parties, abrasives of different particle size ranges may be mixed together. Details of proportions of nominal size, oversize and undersize shall be specified. The maximum particle size shall not exceed3,15 mm and the proportion of particles less than0,2mm shall not
46、 exceed5% (m/m). Property Requirement Test method Particle size range and distribution See Table 1 ISO 11127-2 Apparent density kg/m 3 kg/dm 3 (3,0 to3,3) 10 3 3,0 to 3,3 ISO 11127-3 Mohs hardness a min. 6 ISO 11127-4 Moisture % (m/m) max. 0,2 ISO 11127-5 Conductivity of aqueous extract mS/m max. 25
47、 ISO 11127-6 Water-soluble chlorides % (m/m) max. 0,002 5 ISO 11127-7 a Another method for assessing hardness may be used, together with an appropriate minimum requirement, by agreement between the interested parties.ENISO11126-8:1997 BSI 04-1999 Annex A (informative) Bibliography Commonly reference
48、d national standards for non-metallic abrasives are as follows: 1 DIN 8200:1982, Strahlverfahrenstechnik; Begriffe, Einordnung der Strahlverfahren (Blasting;terms,classification of blasting techniques). 2 DIN 8201 Teil 1:1985, Feste Strahlmittel; Einteilung, Bezeichnung (Abrasives;classification,des
49、ignation). 3 DIN 8201 Teil 5:1985, Feste Strahlmittel, natrlich, mineralisch; Quarzsand (Naturalmineralabrasives; quartz sand). 4 DIN 8201 Teil 6:1985, Feste Strahlmittel, synthetisch, mineralisch; Elektrokorund (Syntheticmineralabrasives; electric corundum). 5 DIN 8201 Teil 9:1986, Feste Strahlmittel, synthetisch, mineralisch; Kupferhttenschlacke, Schmelzkammerschlacke (Synthetic mineral solid abrasives; copper refinery slag, melting chamber slag). Annex ZA (normative) Nor
