1、BS EN ISO15614-3:2008ICS 25.160.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDSpecification andqualification ofwelding procedures formetallic materials Welding procedure testPart 3: Fusion welding of non-alloyedand low-alloyed cast irons (ISO15614-3:2008)Thi
2、s British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 July 2008 BSI 2008ISBN 978 0 580 54475 0Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 15614-3:2008National forewordThis British Standard is the UK implementation of EN ISO1561
3、4-3:2008.The UK participation in its preparation was entrusted to TechnicalCommittee WEE/36, Qualification of welding personnel and weldingprocedures.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the
4、necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 15614-3March 2008ICS 25.160.10English VersionSpecification and qualification of w
5、elding procedures for metallicmaterials - Welding procedure test - Part 3: Fusion welding ofnon-alloyed and low-alloyed cast irons (ISO 15614-3:2008)Descriptif et qualification dun mode opratoire de soudagepour les matriaux mtalliques - preuve de qualificationdun mode opratoire de soudage - Partie 3
6、: Soudage parfusion des fontes non allies et faiblement allies (ISO15614-3:2008)Anforderung und Qualifizierung von Schweiverfahren frmetallische Werkstoffe - Schweiverfahrensprfung - Teil3: Schmelzschweien von unlegierten und niedriglegiertenGusseisen (ISO 15614-3:2008)This European Standard was app
7、roved by CEN on 7 March 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalsta
8、ndards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified t
9、o the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Neth
10、erlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in
11、 any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 15614-3:2008: EBS EN ISO 15614-3:2008EN ISO 15614-3:2008 (E) 3 Foreword This document (EN ISO 15614-3:2008) has been prepared by Technical Committee CEN/TC 121 “Welding“, the secretariat of which is held by DIN, in
12、 collaboration with Technical Committee ISO/TC 44 “Welding and allied processes“. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2008, and conflicting national standards shall be withdr
13、awn at the latest by September 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations
14、, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands
15、, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN ISO 15614-3:2008ISO 15614-3:2008(E) ISO 2008 All rights reserved iiiContents Page Foreword iv Introduction v 1 Scope 1 2 Normative references 1 3 Terms and definitions .2 4 Welding proce
16、sses 3 5 Preliminary welding procedure specification .3 6 Welding procedure test.3 7 Test piece .3 7.1 General3 7.2 Shape and dimensions of test piece .4 7.3 Welding of test piece.4 8 Examination and testing .5 8.1 Extent of testing.5 8.2 Location and taking of test specimens .6 8.3 Non-destructive
17、testing.6 8.4 Destructive tests6 8.5 Acceptance criteria7 8.6 Re-testing .7 9 Range of qualification .7 9.1 General7 9.2 Qualification related to the manufacturer .7 9.3 Qualification related to the material.8 9.4 Qualification common to all welding procedures 10 9.5 Qualification specific to proces
18、ses .12 10 Welding procedure qualification record form.13 Annex A (informative) Welding procedure qualification record form.14 Bibliography 17 BS EN ISO 15614-3:2008ISO 15614-3:2008(E) iv ISO 2008 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide fed
19、eration of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that comm
20、ittee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accorda
21、nce with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires
22、 approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15614-3 was prepared by the Europ
23、ean Committee for Standardization (CEN) Technical Committee CEN/TC 121, Welding, in collaboration with Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 10, Unification of requirements in the field of metal welding, in accordance with the Agreement on technical cooperation
24、 between ISO and CEN (Vienna Agreement). Requests for official interpretations of any aspect of this part of ISO 15614 should be directed to the Secretariat of ISO/TC 44/SC 10 via your national standards body. A complete listing of these bodies can be found at www.iso.org. ISO 15614 consists of the
25、following parts, under the general title Specification and qualification of welding procedures for metallic materials Welding procedure test: Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys Part 2: Arc welding of aluminium and its alloys Part 3: Fusion welding of no
26、n-alloyed and low-alloyed cast irons Part 4: Finishing welding of aluminium castings Part 5: Arc welding of titanium, zirconium and their alloys Part 6: Arc and gas welding of copper and its alloys Part 7: Overlay welding Part 8: Welding of tubes to tube-plate joints Part 10: Hyperbaric dry welding
27、Part 11: Electron and laser beam welding Part 12: Spot, seam and projection welding Part 13: Resistance butt and flash welding BS EN ISO 15614-3:2008ISO 15614-3:2008(E) ISO 2008 All rights reserved vIntroduction Details of International Standards dealing with specification and qualification of weldi
28、ng procedures are given in ISO 15607:2003, Annex A. Welding procedure tests for flash welding are presented in ISO 15614-13 and for friction welding in ISO 15620. BS EN ISO 15614-3:2008BS EN ISO 15614-3:2008INTERNATIONAL STANDARD ISO 15614-3:2008(E) ISO 2008 All rights reserved 1Specification and qu
29、alification of welding procedures for metallic materials Welding procedure test Part 3: Fusion welding of non-alloyed and low-alloyed cast irons 1 Scope This part of ISO 15614 specifies how a preliminary welding procedure specification (pWPS) for production and repair welding of non-alloyed and low-
30、alloyed cast irons is qualified by fusion welding procedure tests. This part of ISO 15614 defines the conditions for execution of the welding procedure tests and the range of qualification for welding procedures for all practical welding operations within the range of a defined list of variables. Th
31、is part of ISO 15614 is applicable to all new welding procedures. However, it does not invalidate previous welding procedure tests made to former national standards or specifications. Where additional tests have to be carried out to make the qualification technically equivalent, it is only necessary
32、 to do the additional tests on a test piece made in accordance with this part of ISO 15614. Additional tests may be required by application standards. This part of ISO 15614 is applicable to welding non-alloyed and low-alloyed grey cast iron castings according to: EN 1561; EN 1562; EN 1563; and EN 1
33、564. The principles of this part of ISO 15614 are also applicable for welding cast iron to steel or to other unalloyed and low-alloyed cast iron materials. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the
34、 edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 783, Metallic materials Tensile testing at elevated temperature ISO 6947, Welds Working positions Definitions of angles of slope and rotation ISO 14175, Welding consu
35、mables Gases and gas mixtures for fusion welding and allied processes ISO 15607:2003, Specification and qualification of welding procedures for metallic materials General rules ISO 15609-1, Specification and qualification of welding procedures for metallic materials Welding procedure specification P
36、art 1: Arc welding ISO 15609-2, Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 2: Gas welding BS EN ISO 15614-3:2008ISO 15614-3:2008(E) 2 ISO 2008 All rights reservedISO 15611, Specification and qualification of welding procedures fo
37、r metallic materials Qualification based on previous welding experience ISO 15613, Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test EN 571-1, Non destructive testing Penetrant testing Part 1: General principles EN 970, No
38、n-destructive examination of fusion welds Visual examination EN 1011-1, Welding Recommendations for welding of metallic materials Part 1: General guidance for arc welding EN 1011-8:2004, Welding Recommendations for welding of metallic materials Part 8: Welding of cast irons EN 1321, Destructive test
39、s on welds in metallic materials Macroscopic and microscopic examination of welds EN 1561, Founding Grey cast irons EN 1562, Founding Malleable cast irons EN 1563, Founding Spheroidal graphite cast irons EN 1564, Founding Austempered ductile cast irons EN 10002-1, Metallic materials Tensile testing
40、Part 1: Method of test at ambient temperature 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 15607 and the following apply. 3.1 production welding any welding carried out during manufacture before final delivery to the end user 3.2 joint welding pro
41、duction welding used to join components together 3.3 finishing welding production welding carried out in order to remove casting defects to ensure the required quality of castings 3.4 repair welding any welding carried out after delivery to the end user, i.e. after the product has been in service BS
42、 EN ISO 15614-3:2008ISO 15614-3:2008(E) ISO 2008 All rights reserved 34 Welding processes Welding is covered by the following welding processes in accordance with ISO 4063: 111 manual metal arc welding (metal arc welding with covered electrode); shielded metal arc welding (USA); 114 self-shielded tu
43、bular-cored arc welding; 121 submerged arc welding with one wire electrode; 131 metal inert gas welding, MIG welding; gas metal arc welding (USA); 135 metal active gas welding, MAG welding; gas metal arc welding (USA); 136 tubular-cored metal arc welding with active gas shield; flux cored arc weldin
44、g (USA); 141 tungsten inert gas welding; TIG welding; gas tungsten arc welding (USA); 15 plasma arc welding; 311 oxy-acetylene welding; oxyacetylene welding (USA). 5 Preliminary welding procedure specification (pWPS) The pWPS shall be prepared in accordance with ISO 15609-1 or ISO 15609-2. 6 Welding
45、 procedure test The welding and testing of test pieces shall be in accordance with Clauses 7 and 8. The welder or welding operator, who undertakes the welding procedure test satisfactorily in accordance with this part of ISO 15614, is qualified to weld within the range of qualification according to
46、Clause 9. 7 Test piece 7.1 General The test piece shall comply with the requirements of 7.2, 7.3, and Figure 1. It can be cast separately or removed from the casting/component. Preparation of sufficiently large test pieces is by machining. When the standardized test pieces as shown in this part of I
47、SO 15614 do not represent the production/joint geometry, the use of ISO 15611 or ISO 15613 shall be required. BS EN ISO 15614-3:2008ISO 15614-3:2008(E) 4 ISO 2008 All rights reservedDimensions in millimetres Key 1 discard 2 inspection length The dimensions shown are for information only and may be a
48、djusted to meet production and testing requirements. The edges of the groove should be smooth rounded. Edge preparation of the groove and fit-up shall be as detailed in the pWPS. aIn accordance with Table 3 or Table 4. ba = 5 mm to 15 mm or = 5 to 20. Figure 1 Test piece 7.2 Shape and dimensions of
49、test piece The length or number of test pieces shall be sufficient to allow all required tests to be carried out. Additional test pieces, or longer test pieces than the minimum size, may be prepared in order to allow for extra and/or for retesting test specimens (see 8.5). The thickness of the test pieces shall be selected in accordance with 9.3.2. 7.3 Welding of test piece Preparation and welding of test piece(s) shall be carried out in accordance with a
