1、BRITISH STANDARD BS EN ISO 15983:2002 Incorporating Corrigenda Nos. 1 and 2 Open end blind rivets with break pull mandrel and protruding head A2/A2 The European Standard EN ISO 15983:2002 has the status of a British Standard ICS 21.060.40 BS EN ISO 15983:2002 This British Standard, having been prepa
2、red under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 20 November 2002 BSI 23 November 2002 ISBN 0 580 40758 6 National foreword This British Standard is the official English language versi
3、on of EN ISO 15983:2002. It is identical with ISO 15983:2002. BS EN ISO 15983:2002, together with BS EN ISO 15980:2002, BS EN ISO 15981:2002, BS EN ISO 15982:2002, BS EN ISO 15984:2002, BS EN ISO 16582:2002, BS EN ISO 16583:2002, BS EN ISO 16584:2002 and BS EN ISO 16585:2002, supersedes BS 7349-2:19
4、93 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee FME/6, Rivets, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implemen
5、t international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does n
6、ot purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European c
7、ommittee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, the
8、EN ISO foreword page, the ISO title page, pages ii and iii, a blank page, pages 1 to 6, the Annex ZA page and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments 14321 Corrigendum No
9、. 1 28 January 2003 Replacing the EN ISO foreword page and incorporating the Annex ZA page 15323 Corrigendum No. 2 23 November 2004 Addition of supersession detailsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM ENISO15983 November2002 ICS21.060.40 Englishversion Openendblindrivetswithbreakpullmandre
10、landprotruding headA2/A2(ISO15983:2002) Rivetsaveuglesrupturedetigecorpsouvert,tte bombeA2/A2(ISO15983:2002) OffeneBlindnietemitSollbruchdornundFlachkopfA2/A2 (ISO15983:2002) ThisEuropeanStandardwasapprovedbyCENon14October2002. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstip
11、ulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheManagementCentreortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,Frenc
12、h,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheManagementCentrehasthesamestatusasthe official versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,CzechRepublic,Denmark,Finland,France,Germany,Greece, Iceland,Ir
13、eland,Italy,Luxembourg,Malta,Netherlands,Norway,Portugal,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2002CEN Allrightsofexploitationinanyformandbyanymeansreserved
14、worldwideforCENnationalMembers. Ref.No.ENISO15983:2002ECORRECTED20021218 Foreword Thisdocument(ENISO15983:2002)hasbeenpreparedbyTechnicalCommitteeISO/TC2 “Fasteners“incollaborationwithTechnicalCommitteeCEN/TC185“Threadedandnon threadedmechanicalfastenersandaccessories“,thesecretariatofwhichisheldbyD
15、IN. ThisEuropeanStandardshallbegiventhestatusofanationalstandard,eitherbypublicationof anidenticaltextorbyendorsement,atthelatestbyMay2003,andconflictingnationalstandards shallbewithdrawnatthelatestbyMay2003. AccordingtotheCEN/CENELECInternalRegulations,thenationalstandardsorganizationsof thefollowi
16、ngcountriesareboundtoimplementthisEuropeanStandard:Austria,Belgium,Czech Republic,Denmark,Finland,France,Germany,Greece,Iceland,Ireland,Italy,Luxembourg, Malta,Netherlands,Norway,Portugal,Spain,Sweden,SwitzerlandandtheUnitedKingdom. Endorsementnotice ThetextofISO15983:2002hasbeenapprovedbyCENasENISO
17、15983:2002withoutany modifications. NOTENormativereferencestoInternationalStandardsarelistedinAnnexZA(normative). ENISO15983:2002 Reference number ISO 15983:2002(E)INTERNATIONAL STANDARD ISO 15983 First edition 2002-11-01 Open end blind rivets with break pull mandrel and protruding head A2/A2 Rivets
18、 aveugles rupture de tige corps ouvert, tte bombe A2/A2 ENISO15983:2002DPlcsid Fremia ihTs PDF file mc yatnoaie nmt deddebyfepca.se Icca ncnadrow eitA hebods licsneilop gnic,y tihs file mirp eb yatniv ro deewb detu slahl ton ide ebtlnu desse tt ehyfepacse wihce era hml era deddebicsnede to i dnasntl
19、alde t noeh comtupfrep remroign tide ehti.gn Iwod nnlidaogn tihs fil,e trapies ccatpe tiereht nsnopser ehiiblity fo ton ifnriignA gnebods licnesilop gnic.y I ehTStneC Oarl Scerteiraat cacpets l oniibality it nihs .aera Ai ebods a tedarmfo kra Aebod SystemI snctaropro.de teDials fo ts ehfotworp eracu
20、dts ust dec ortaet eihs PDF filc eeb na fi dnuot nlareneG eh Ifnler otait evt of ehil;e tP ehD-Fcrtaeiarap nomtesre wretpo eimizf deirp rotni.gn Evyre csah era t neebkat nesne ot eruaht tf ehili es siutlbaf esu roI yb eSO memidob rebse. It neh lnuikletneve y ttah a lborpem leratign ti ot is fnuo,d l
21、psaee ifnrom ttneC ehlar Secrteirata at tsserdda eh igleb nevwo. ISO 2002 Athgir lls serevr.de selnUs towrehise specfi,dei trap on fo this ilbupctanoi may cudorper ebtu ro deziliyna ni de fomr yb ro nam y,snae lecetinorc m roecinahcal, inclidutohp gnocpoiym dna gnicrfoilm, wittuoh repmissii now nrit
22、if gnrom ietreh ISa Ot tserdda ehs lebwo I roSOs membre ydob it neh ctnuoo yrf ttseuqer eh.re ISO cirypothg fofice saCe tsopale 65 eneG 1121-HC 02 av leT. 4 + 10 947 22 1 11 xaF0 947 22 14 + 9 74 E-mial coirypthgis.oc h Web ww.wiso.ch ii ENISO15983:2002 iiiForeword ISO (the International Organizatio
23、n for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has
24、 the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Inter
25、national Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publicat
26、ion as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all su
27、ch patent rights. ISO 15983 was prepared by Technical Committee ISO/TC 2, Fasteners. Annex A of this International Standard is for information only. ENISO15983:2002INTENRATIONAL TSANDADR IS:38951 O2002(E)1Open end blind rivets with break pull mandrel and protruding head A2/A2 1 Scope This Internatio
28、nal Standard specifies dimensional and mechanical characteristics and application data for open end blind rivets with break pull mandrel and protruding head, with an austenitic stainless steel body (A2) and an austenitic stainless steel mandrel (A2) and with nominal diameters, d, from 3 mm up to and
29、 including 5 mm. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However,
30、parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC m
31、aintain registers of currently valid International Standards. ISO 3269:2000, Fasteners Acceptance inspection ISO 3506-1:1997, Mechanical properties of corrosion-resistant stainless-steel fasteners Part 1: Bolts, screws and studs ISO 14588:2000, Blind rivets Terminology and definitions ISO 14589:2000
32、, Blind rivets Mechanical testing 3 Dimensions 3.1 General Symbols and designations of dimensions are specified in ISO 14588. 3.2 Rivet dimensions See Figure 1 and Table 1. ENISO15983:2002ISO 15983:2002(E) 2 Figure 1 Rivet dimensions Tableau 1 Rivet dimensions Dimensions in millimetres nom. 3 3,2 4
33、4,8 5 max. 3,08 3,28 4,08 4,88 5,08 d min. 2,85 3,05 3,85 4,65 4,85 max. 6,3 6,7 8,4 10,1 10,5 d kmin. 5,4 5,8 6,9 8,3 8,7 Rivet body k max. 1,3 1,3 1,7 2 2,1 d mmax. 2,05 2,15 2,75 3,2 3,25 Mandrel p min. 25 25 25 27 27 Blind length b max. l max+ 4 l max+ 4 l max+ 4,5 l max+ 5 l max+ 5 Rivet length
34、 l bnom. = min. max. Recommended grip ranges a6 7 0,5 to 3,0 1,0 to 2,5 1,5 to 2,0 8 9 3 to 5 2,5 to 4,5 2 to 4 10 11 5,0 to 6,5 4,5 to 6,5 4 to 6 12 13 6,5 to 8,5 6,5 to 8,5 6 to 8 14 15 8,5 to 10,5 8,5 to 10,0 16 17 10,5 to 12,5 10 to 12 8 to 11 18 19 12 to 14 11 to 13 20 21 14 to 16 13 to 16 25 2
35、6 16 to 21 16 to 19 NOTE The rivet body dimensions are generated from the design formulae specified in annex A. aThe grip ranges of rivets with dimensions as given in Table 1, with the material combination as given in clause 4 are specified by the minimum and maximum grip lengths. The minimum grip l
36、engths are given as a recommendation only. It may be possible to go into individual cases below the minimum values. bNominal lengths greater than 25 mm shall be specified in 5 mm increments. For availability and grip range refer to manufacturer. ENISO15983:2002ISO 15983:2002(E) 33.3 Clearance hole d
37、iameters The diameters of the clearance holes, d h1 , to accommodate the rivet in the components to be fastened are given in Table 2. Table 2 Clearance hole diameters Dimensions in millimetres d d h1nom. min. max. 3 3,1 3,2 3,2 3,3 3,4 4 4,1 4,2 4,8 4,9 5,0 5 5,1 5,2 Non-conformance to the values li
38、sted in Table 2 may result in assembly difficulties and/or reduction in the shear and tensile loads specified in Table 3. When necessary, to facilitate alignment, only the component on the access side may have a clearance hole larger than specified in Table 2 (see Figure 2). This may also result in
39、a reduction of the shear and tensile loads specified in Table 3. aEnlarged clearance hole Figure 2 Enlarged clearance hole to facilitate alignment 4 Material and finish Blind rivets in accordance with this International Standard shall have a rivet body and a mandrel made of austenitic stainless stee
40、l grade A2 in accordance with ISO 3506-1 and shall have mechanical properties as specified in clause 5. Material specification is at the discretion of the manufacturer. The surface of rivet body and mandrel shall be plain, i.e. in natural finish. ENISO15983:2002ISO 15983:2002(E) 4 5 Mechanical prope
41、rties The minimum shear load, minimum tensile load and maximum mandrel break load shall be as specified in Table 3 when tested in accordance with ISO 14589. Table 3 Mechanical properties Shear load Tensile load Mandrel break load d nom. min. min. max. mm N N N 3 1 800 2 200 4 100 3,2 1 900 2 500 4 5
42、00 4 2 700 3 500 6 500 4,8 4 000 5 000 8 500 5 4 700 5 800 9 000 6 Mandrel push-out resistance The load to push out the mandrel shall exceed 10 N when tested in accordance with ISO 14589. 7 Mandrel head retention capability The portion of the mandrel remaining in the set rivet shall not be ejected b
43、y the application of the head retention test load specified in Table 4 when tested in accordance with ISO 14589. Table 4 Mandrel head retention test loads d Head retention test load nom. mm N 3 35 3,2 35 4 40 4,8 45 5 45 8 Workmanship Rivets shall be free from burrs and harmful defects and shall hav
44、e well-formed heads and shanks. After setting, rivets shall not show evidence of cracking when viewed at 5 magnification. 9 Acceptance testing If there is no other agreement, acceptance inspection in accordance with ISO 3269 applies. ENISO15983:2002ISO 15983:2002(E) 510 Designation EXAMPLE An open e
45、nd blind rivet, with break pull mandrel and protruding head, with nominal diameter d = 4,8 mm and nominal length l = 12 mm with an austenitic stainless body (A2) and an austenitic stainless steel mandrel (A2) is designated as follows: Blind rivet ISO 15983 - 4,8 12 - A2/A2 ENISO15983:2002ISO 15983:2
46、002(E) 6 Annex A (informative) Design formulae A.1 General Blind rivets in accordance with this International Standard comply with the following design formulae and tolerances. A.2 Shank diameter The maximum shank diameter complies with the formula: d max= d nom+ 0,08 mm The minimum shank diameter c
47、omplies with the formula: d min= d nom 0,15 mm A.3 Head diameter The maximum head diameter complies with the formula: d k max= 2,1 d nomrounded to one decimal place. A.4 Head diameter tolerance The head diameter tolerance is h16 for d nomu 3,2 mm and h17 for d nom 3,2 mm. A.5 Head height The maximum
48、 head height complies with the formula: k max= 0,415 d nomrounded to one decimal place. A.6 Clearance hole diameter The clearance hole diameter for blind rivet application complies with the formulae: d h1 max= d nom+ 0,2 mm d h1 min= d nom+ 0,1 mm ENISO15983:2002AnnexZA (normative) Normativereferencestointernationalpublications withtheir
