1、ICS 75.180.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISHSTANDARDPetroleumandnaturalgasindustriesDownholeequipmentSandscreensBS EN ISO 17824:2014National forewordThis British Standard is the UK implementation of EN ISO 17824:2014. It is identical to ISO 17824:2009. I
2、t supersedes BS ISO 17824:2009, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PSE/17, Materials and equipment for petroleum, petrochemical and natural gas industries.A list of organizations represented on this committee can be obtained on request to
3、its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.BS EN ISO 17824:2014This British Standardwas published under theau
4、thority of the StandardsPolicy and StrategyCommittee on 31 October2009Amendments/corrigenda issued since publicationDate Comments 30 September 2014 This corrigendum renumbers BS ISO 17824:2009 as BS EN ISO 17824:2014ISBN 978 0 580 85023 3 The British Standards Institution 2014. Published by BSI Stan
5、dards Limited 2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 17824 August 2014 ICS 75.180.10 English Version Petroleum and natural gas industries - Downhole equipment - Sand screens (ISO 17824:2009) Industries du ptrole et du gaz naturel - Equipement de fond de puits - Tamis de contrle
6、 de sable (ISO 17824:2009) Erdl- und Erdgasindustrie - Bohrlochausrstungen - Sandfilter (ISO 17824:2009) This European Standard was approved by CEN on 31 July 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Stand
7、ard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English
8、, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bul
9、garia, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, T
10、urkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members
11、. Ref. No. EN ISO 17824:2014 EForeword The text of ISO 17824:2009 has been prepared by Technical Committee ISO/TC 67 “Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries” of the International Organization for Standardization (ISO) and has been taken o
12、ver as EN ISO 17824:2014 by Technical Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication o
13、f an identical text or by endorsement, at the latest by February 2015, and conflicting national standards shall be withdrawn at the latest by February 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall
14、not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmar
15、k, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement noti
16、ce The text of ISO 17824:2009 has been approved by CEN as EN ISO 17824:2014 without any modification. ii ISO 2009 All rights reservedBS EN ISO 17824:2014 EN ISO 17824:2014 (E) ISO 2009 All rights reserved iiiContents PageForeword ivIntroduction v1Scope. 12Normative references. 13Terms and definition
17、s. 24Abbreviated terms 65Functional specification. 65.1 General. 65.2 Product type 75.3 Sand screen parameters 75.4 Well parameters 75.5 Operational parameters. 75.6 Environmental compatibility 85.7 Compatibility with related well equipment. 85.8 Design validation grades. 85.9 Quality grades. 85.10
18、Special quality requirements. 86Technical specification 96.1 General. 96.2 Technical characteristics. 96.3 Design criteria. 96.4 Design verification 96.5 Design validation 106.6 Design changes 106.7 Design validation by scaling . 117Supplier/manufacturer requirements 137.1 General. 137.2 Documentati
19、on and data control. 137.3 Product identification. 147.4 Quality control. 148Storage and transport 238.1 Storage.238.2 Product protection 238.3 Transport. 23Annex A (normative) Collapse pressure test 24Annex B (normative) Burst pressure test 27Annex C (informative) Sized-bead test method. 30Annex D
20、(informative) Sand control screen illustrations. 32Annex E (informative) Wire-wrap screen illustrations 34Annex F (informative) Pre-pack screen illustrations 35Annex G (informative) Metal-mesh screen illustrations. 36Annex H (informative) Increased wire-wrap slot size inspection 37Bibliography. 38BS
21、 EN ISO 17824:2014 ISO 17824:2014 (E)iv ISO 2009 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technica
22、l committees. Each member body interested in a subject for which a tec hnical committee has beenestablished has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closelywith
23、 the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft Interna
24、tional Standardsadopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be
25、 the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 17824 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 4, Drilling a
26、nd productionequipment. BS EN ISO 17824:2014 ISO 17824:2014 (E) ISO 2009 All rights reserved vIntroduction This International Standard has been developed by user/purchasers and supplier/manufacturers of sandcontrol screens intended for use in petroleum and natural gas wells. This International Stand
27、ard providesrequirements and information to both parties regarding the manufacture, m echanical properties and testing of sand control screens. Further, this International Standard addresses supplier/manufacturer requirements that set the minimum parameters with which it is necessary that supplier/m
28、anufacturers comply to claim conformitywith this International Standard. This International Standard is structured with grades of increased requirements for both design validation andquality control. Three design validation grades (V1, V2 and V3) and three quality grades (Q1, Q2 and Q3)provide the u
29、ser/purchaser the choiceof requirements to meet a specific preference or application. Designvalidation grade V3 and qualitygrade Q3 represent equipment designed and manufactured consistent with minimum industry practice.Included within this International Standard are normative annexes A and B specif
30、ying test methods fordetermining the collapse and burst strength of sand control screens. Info rmative annexes C, D, E, F, G and H include measurement criteria for sand control screen filter media, illustrati ons of the three types of sand control screens, and increased wire-wrap slot size inspectio
31、n requirements.It is necessary that users of this International Standard be aware that r equirements above those outlined in this International Standard can be needed for individual applications. This International Standard is not intended to inhibit a supplier/manufacturer from offering, or the use
32、r/purchaser from accepting, alternativeequipment or engineering solutions. This can be particularly applicable where there is innovative ordeveloping technology.Where an alternative is offered, it is the res ponsibility of the supplier/manufacturer toidentifyany variations from this International St
33、andard and provide details. BS EN ISO 17824:2014 ISO 17824:2014 (E)BS EN ISO 17824:2014 ISO 17824:2014 (E)INTERNATIONAL STANDA RD ISO 2009 All rights reserved 1Petroleum and natural gas industries Downhole equipment Sand screens 1 Scope This International Standard provides the requirements and guide
34、lines for sand control screens for use in thepetroleum and natural gas industries. Included are the requirements for design, design validation, functionalevaluation, manufacturing, storage and transport. The requirements of this International Standard are applicable to wire-wrap screens, pre-pack sc
35、reens and metal-mesh screens as defined herein. The following items are outside the scope of this International Standard: expandable sand screens, slotted liners or tubing and accessory items such as centralizers or bull plugs; shunt screen technology, inflow control devices, downhole sensors and se
36、lective isolation devices, even where they can be an integral part of the sand control screen; screen filtration performance criteria, including test methods or a nalysis for sand retention efficiency; end connections of the basepipe. 2 NormativereferencesThe following referenced documents are indis
37、pensable for the application of this document. The wayin whichthese referenced documents are cited determines the extent (in w hole orpart) towhich theyapply. For dated references, only the edition cited applies. For undated references, the latest edition of the referenceddocument (including any ame
38、ndments) applies.ISO 10414-1:2008, Petroleum and natural gas industries Field testing of drilling fluids Part 1: Water-based fluidsISO11960, Petroleum and natural gas industries Steel pipes for use as casingor tubing for wellsNOTE ISO 11960 has been back adopted by API as API SPEC 5CT. Therefore, fo
39、r the purposes of the provisions ofthis International Standard which cite ISO 11960, API SPEC 5CT is equivalent to ISO 11960. ISO/IEC 17025, General requirements for the competence of testing and calibration laboratoriesISO 9000, Quality management systems Fundamentals and vocabularyASME, Boiler and
40、 Pressure Vessel Code BPVC Section II: Materials: Part D: PropertiesASME, Boiler and Pressure Vessel Code BPVC Section VIII: 1998, Div. 1, Appendix 8: Methods for LiquidPenetrant Examination (PT)ASME, Boiler and Pressure Vessel Code BPVC Section IX: Welding and Brazing QualificationsASTM E11, Standa
41、rd Specification for Wire Cloth and Sieves for Testing PurposesASTME165, Standard Test Method for Liquid Penetrant Examination ISO 17824:2014 (E)BS EN ISO 17824:2014 2 ISO 2009 All rights reserved3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 9000 a
42、nd the following apply.3.1 annular gravel packsized sand or synthetic proppant p laced in the annulus outside the sand control screen during gravel pack ing3.2 basepipe tubulars that have perforations or sl ots to allow fluid flow through the screen jacket NOTE See FiguresE.1, F.1 and G.1.3.3 box ha
43、ndling length axial length of blank basepipe on a sand control screen, measured between the end of the box connectionand the nearest component along the basepipe NOTE See FiguresD.4 and D.5. 3.4 center break axial length of blank pipe between two screen jackets on a sand control screen NOTE See Figu
44、re D.5. 3.5 component individual part of an assembly3.6 design familygroup of sand control screens wherein the configuration, materials,and functionality are the same and the design stress levels in relation to material mechanical properties are based on the same criteria 3.7 design validation proce
45、ss of proving a design by testing to demonstrate conformity of the product to design requirementsISO/TS 29001 3.8 design verification process of examining the result of a given design or development activity to determine conformity withspecified requirementsISO/TS 29001 3.9 direct-wrap screensand sc
46、reen in which the screen jacket rib wires are in direct contact with the base pipe along the axial length NOTE See Annexes E and F.3.10 direct-wrap pre-pack screenpre-pack screen in which the inner screen, which maybe wire-wrap or metal-mesh, is a direct-wrap screen NOTE See Annex F. BS EN ISO 17824
47、:2014 ISO 17824:2014 (E) ISO 2009 All rights reserved 33.11 downhole sensordevice incorporated into the sand control screen to measure various downhole conditions3.12 drainage or support layercomponent used in metal-mesh sc reens to provide structural support and/or to facilitate flow between the ba
48、sepipe perforations and metal meshNOTE See Figure G.1.3.13 drift OD minimum ID of the drift toolutilized to verify screen assembly OD clearance 3.14 end ring component used to seal the annular gap between the ends of the screen jacket and basepipe 3.15 filter media OD metal-mesh screens metal-meshOD
49、 wire-wrap screens wrap-wire OD pre-pack screens outermost wrap-wire ODNOTE See Figures D.1, D.2 and D.3.3.16 fluid-loss control pillfluid with a concentration of a wide array of sized particles that forms a filter cake that seals off a screensurface with little or no leak-off through the screens slot openings or pores3.17 gravel packing well completion method used for the purpose of excluding formation sand from entering the well bore and including a sand control screen, sized sand or synthetic proppant 3.18 inflow con
