1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationDD CEN ISO/TS 16410-1:2011Electronic fee collection Evaluation of equipment forconformity to ISO/TS 17575-3Part 1: Test suite structure and test purposes(ISO/TS 16410-1:2011)DD C
2、EN ISO/TS 16410-1:2011 DRAFT FOR DEVELOPMENTNational forewordThis Draft for Development is the UK implementation of CEN ISO/TS16410-1:2011.This publication is not to be regarded as a British Standard.It is being issued in the Draft for Development series of publicationsand is of a provisional nature
3、. It should be applied on thisprovisional basis, so that information and experience of its practicalapplication can be obtained.Comments arising from the use of this Draft for Developmentare requested so that UK experience can be reported to theinternational organization responsible for its conversi
4、on toan international standard. A review of this publication willbe initiated not later than 3 years after its publication by theinternational organization so that a decision can be taken on itsstatus. Notification of the start of the review period will be made inan announcement in the appropriate i
5、ssue of Update Standards.According to the replies received by the end of the review period,the responsible BSI Committee will decide whether to support theconversion into an international Standard, to extend the life of theTechnical Specification or to withdraw it. Comments should be sentto the Secr
6、etary of the responsible BSI Technical Committee at BritishStandards House, 389 Chiswick High Road, London W4 4AL.The UK participation in its preparation was entrusted to TechnicalCommittee EPL/278, Road transport informatics.A list of organizations represented on this committee can beobtained on re
7、quest to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012ISBN 978 0 580 71679 9ICS 03.220.20; 35.240.60Compliance with a British Standard cannot confer immuni
8、ty fromlegal obligations.This Draft for Development was published under the authority ofthe Standards Policy and Strategy Committee on 31 January 2012.Amendments issued since publicationDate Text affectedTECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN ISO/TS 16410-1 Octob
9、er 2011 ICS 35.240.60; 03.220.20 English Version Electronic fee collection - Evaluation of equipment for conformity to ISO/TS 17575-3 - Part 1: Test suite structure and test purposes (ISO/TS 16410-1:2011) Perception du tlpage - valuation de la conformit de lquipement lISO/TS 17575-3 - Partie 1: Stru
10、cture de la suite dessais et objectifs des essais (ISO/TS 16410-1:2011) Elektronische Gebhrenerfassung - Konformittsevaluierung von Equipment zur CEN ISO/TS 17575-3 - Teil 1: Struktur der Testfolge und Testabsichten (ISO/TS 16410-1:2011) This Technical Specification (CEN/TS) was approved by CEN on 1
11、5 August 2011 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN members
12、are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the poss
13、ible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
14、Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any f
15、orm and by any means reserved worldwide for CEN national Members. Ref. No. CEN ISO/TS 16410-1:2011: EDD CEN ISO/TS 16410-1:2011CEN ISO/TS 16410-1:2011 (E) 3 Foreword This document (CEN ISO/TS 16410-1:2011) has been prepared by Technical Committee CEN/TC 278 “Road transport and traffic telematics”, t
16、he secretariat of which is held by NEN, in collaboration with Technical Committee ISO/TC 204 “Intelligent transport systems”. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for ide
17、ntifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Franc
18、e, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DD CEN ISO/TS 16410-1:2011ISO/TS 16410-1:2011(E) ISO 2011 All rights reserved iiiContents
19、 Page Foreword iv Introduction . v 1 Scope 1 2 Normative references 2 3 Terms and definitions . 2 4 Abbreviated terms . 4 5 Test Suite Structure (TSS) 4 5.1 Structure . 4 5.2 Reference to conformance test specifications 6 5.3 Test Purposes (TP) 6 5.4 Conformance test report . 7 Annex A (normative) T
20、est Purposes (TP) for Front End . 8 Annex B (normative) Test purposes (TP) for Back End 92 Annex C (normative) Data Structures . 124 Annex D (normative) PCTR for Front End 135 Annex E (normative) PCTR for Back End . 141 Bibliography 147 DD CEN ISO/TS 16410-1:2011ISO/TS 16410-1:2011(E) iv ISO 2011 Al
21、l rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subj
22、ect for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IE
23、C) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committ
24、ees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. In other circumstances, particularly when there is an urgent market requirement for such documents, a technical committee may decide to
25、 publish other types of document: an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in an ISO working group and is accepted for publication if it is approved by more than 50 % of the members of the parent committee casting a vote; an ISO Technical Sp
26、ecification (ISO/TS) represents an agreement between the members of a technical committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting a vote. An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a
27、further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an International Standard or be withdrawn. Attention is drawn to the possibility t
28、hat some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO/TS 16410-1 was prepared by Technical Committee ISO/TC 204, Intelligent transport systems, in collaboration with Technical Committee CEN/
29、TC 278, Road Transport and Traffic Telematics. ISO/TS 16410 consists of the following parts, under the general title Electronic fee collection Evaluation of equipment for conformity to ISO/TS 17575-3: Part 1: Test suite structure and test purposes Part 2: Abstract test suites DD CEN ISO/TS 16410-1:2
30、011ISO/TS 16410-1:2011(E) ISO 2011 All rights reserved vIntroduction This part of ISO 16410 is part of a set of standards that supports interoperability of autonomous EFC-systems, which includes ISO/TS 17575 parts 1 to 4 that define the EFC context data, their charge reports and their use of communi
31、cation infrastructure. Within the suite of EFC standards this conformance evaluation procedure defines the process and tests for conformity evaluation of Front End and Back End that comply with the requirements in ISO/TS 17575-3. This part of ISO 16410 is intended to assess Front End and Back End ca
32、pabilities, assess Front End and Back End behaviour, serve as a guide for Front End and Back End conformance evaluation and type approval, achieve comparability between the results of the corresponding tests applied in different places at different times, and facilitate communications between partie
33、s. This part of ISO 16410 is based on ISO/TS 17575-3, and the ISO 9646 family of standards on conformance test methodology. DD CEN ISO/TS 16410-1:2011DD CEN ISO/TS 16410-1:2011TECHNICAL SPECIFICATION ISO/TS 16410-1:2011(E) ISO 2011 All rights reserved 1Electronic fee collection Evaluation of equipme
34、nt for conformity to ISO/TS 17575-3 Part 1: Test suite structure and test purposes 1 Scope This part of ISO/TS 16410 specifies the test suite structure (TSS) and test purposes (TP) to evaluate the conformity of Front End and Back End to ISO/TS 17575-3. The objective of this part of ISO/TS 16410 is t
35、o provide a basis for conformance tests for the Front End and the Back End in Electronic Fee Collection (EFC) based on autonomous on-board equipment (OBE) to enable interoperability between different equipment supplied by different manufacturers. Autonomous OBE operates without relying on dedicated
36、road-side infrastructure by employing wide-area technologies such as Global Navigation Satellite Systems (GNSS) and Cellular Communications Networks (CN). These EFC systems are referred to by a variety of names. Besides the terms autonomous systems and GNSS/CN systems, also the terms GPS/GSM systems
37、 and wide-area charging systems are in use. Autonomous systems use satellite positioning, often combined with additional sensor technologies such as gyroscopes, odometers, and accelerometers, to localise the vehicle and to find its position on a map containing the charged geographic objects, such as
38、 charged roads or charged areas. From the charged objects, the vehicle characteristics, the time of day and other data that are relevant for describing road use, the tariff and ultimately the road usage fee is determined. For more information regarding autonomous systems, please refer to ISO/TS 1757
39、5-3. Testing of the following behaviours and functionalities is outside of the scope of this part of ISO/TS 16410: dynamic behaviour, i.e. sequence of messages and triggering events that must be exchanged/happen to fulfil certain charging scenarios; profiles and business logic built on top of partic
40、ular pricing schemas; authentication, as its handling is not described in ISO/TS 17575-3; Front End behaviour with respect to optional data elements in ChargeReportConfiguration, as handling of configurations requesting presence/absence of parent data element, and absence/presence of child data elem
41、ent is not specified in ISO/TS 17575-3. As ISO/TS 17575-3 does not specify any invalid behaviour of Front End and Back End, BI test purposes are not applicable for any test purpose group. DD CEN ISO/TS 16410-1:2011ISO/TS 16410-1:2011(E) 2 ISO 2011 All rights reserved2 Normative references The follow
42、ing referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC 9646-6, Information technology Open Systems Interco
43、nnection Conformance testing methodology and framework Part 6: Protocol profile test specification ISO/TS 17575-1, Electronic fee collection Application interface definition for autonomous systems Part 1: Charging ISO/TS 17575-3, Electronic fee collection Application interface definition for autonom
44、ous systems Part 3: Context data 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 area pricing charging process based on road usage occurring within a given area ISO/TS 17575-1:2010, definition 3.1 3.2 attribute application information formed
45、by one or by a sequence of data elements, and that is managed by different actions used for implementation of a transaction ISO 14906:2011, definition 3.3 3.3 authenticator data appended to, or a cryptographic transformation of, a data unit that allows a recipient of the data unit to prove the sourc
46、e and/or the integrity of the data unit and protect against forgery ISO 14906:2011, definition 3.4 3.4 Back End generic name for the computing and communication facilities of the Service Provider and the Toll Charger exchanging data with the Front End NOTE 1 Adapted from ISO/TS 17575-1. NOTE 2 Accor
47、ding to the architecture defined in ISO 17573, it is assumed in this part of ISO/TS 16410 that the Front End in general communicates with the Back End typically controlled and operated by the Service Provider. 3.5 charge object any object that is part of the toll context description, including toll
48、objects but also used for parking fees, etc. NOTE Adapted from ISO/TS 17575-1. 3.6 charge report data structure transmitted from the Front End to the Back End to report road usage data and supplementary related information ISO/TS 17575-1:2010, definition 3.5 DD CEN ISO/TS 16410-1:2011ISO/TS 16410-1:
49、2011(E) ISO 2011 All rights reserved 33.7 contract expression of an agreement between two or more parties concerning the use of the road infrastructure ISO 14906:2011, definition 3.7 3.8 cordon border line of an area ISO/TS 17575-1:2010, definition 3.8 3.9 cordon pricing charging process based on registering passages of a cordon ISO/TS 17575-1:2010, definition 3.9 3.10 data element datum, which might itself consist of lower level data elements ISO/TS 17575-1:2010, definition 3.10 3
