ETSI EN 301 489-22-2003 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 22 Specifi.pdf

上传人:ownview251 文档编号:729667 上传时间:2019-01-08 格式:PDF 页数:15 大小:76.58KB
下载 相关 举报
ETSI EN 301 489-22-2003 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 22 Specifi.pdf_第1页
第1页 / 共15页
ETSI EN 301 489-22-2003 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 22 Specifi.pdf_第2页
第2页 / 共15页
ETSI EN 301 489-22-2003 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 22 Specifi.pdf_第3页
第3页 / 共15页
ETSI EN 301 489-22-2003 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 22 Specifi.pdf_第4页
第4页 / 共15页
ETSI EN 301 489-22-2003 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 22 Specifi.pdf_第5页
第5页 / 共15页
点击查看更多>>
资源描述

1、 ETSI EN 301 489-22 V1.3.1 (2003-11)Candidate Harmonized European Standard (Telecommunications series) Electromagnetic compatibilityand Radio spectrum Matters (ERM);ElectroMagnetic Compatibility (EMC)standard for radio equipment and services;Part 22: Specific conditions for ground based VHFaeronauti

2、cal mobile and fixed radio equipmentETSI ETSI EN 301 489-22 V1.3.1 (2003-11) 2 Reference REN/ERM-EMC-236-22 Keywords aeronautical, EMC, radio, regulation, VHF ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017

3、- NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case

4、 of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the pres

5、ent document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.or

6、g Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2003. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of

7、 ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI EN 301 489-22 V1

8、.3.1 (2003-11) 3 Contents Intellectual Property Rights4 Foreword.4 1 Scope 5 2 References 5 3 Definitions and abbreviations.6 3.1 Definitions6 3.2 Abbreviations .6 4 Test conditions .7 4.1 General .7 4.2 Arrangements for test signals .7 4.2.1 Arrangement for test signals at the input to the transmit

9、ter 7 4.2.2 Arrangements for test signals at the output from the transmitter7 4.2.3 Arrangements for test signals at the input to the receiver.7 4.2.4 Arrangements for test signals at the output from the receiver 7 4.2.5 Arrangements for testing transmitters and receivers together (as a system) .7 4

10、.3 RF exclusion band for radio communications equipment 8 4.3.1 Transmitter exclusion bands for EM emission measurements8 4.3.2 Receiver exclusion bands for EM emission measurements 8 4.3.3 Transmitter exclusion bands for immunity tests .8 4.3.4 Receiver exclusion bands for immunity tests .8 4.4 Nar

11、row band responses of receivers.8 4.5 Normal test modulation9 5 Performance assessment.9 5.1 General .9 5.2 Equipment which can provide a continuous communications link 9 5.3 Equipment which does not provide a continuous or duty cycle communications link.10 5.4 Ancillary equipment .10 5.5 Equipment

12、classification 10 6 Performance criteria .10 6.1 Performance criteria A for continuous phenomena applied to transmitters and receivers11 6.2 Performance criteria B for transient phenomena applied to transmitters and receivers .11 6.3 Performance criteria C for immunity tests with power interruptions

13、 .11 6.4 Performance criteria for equipment which does not provide a continuous or duty cycle communications link12 6.5 Performance criteria for ancillary equipment tested on a stand alone basis .12 7 Applicability overview.12 7.1 Emission.12 7.1.1 General12 7.1.2 Special conditions.12 7.2 Immunity

14、12 7.2.1 General12 7.2.2 Special conditions.13 Annex A (normative): Definitions of ground based aeronautical radio communications equipment in the scope of the present document14 A.1 Ground based aeronautical VHF radio communications equipment14 A.2 Ground based aeronautical VDL Mode 2 and VDL Mode

15、4 radio communications equipment .14 History 15 ETSI ETSI EN 301 489-22 V1.3.1 (2003-11) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available fo

16、r ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http

17、:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may

18、 become, essential to the present document. Foreword This Candidate Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to a m

19、andate from the European Commission issued under Council Directive 98/34/EC 7 (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. The present document is intended to become a Harmonized Standard, the reference of which will be pu

20、blished in the Official Journal of the European Communities referencing the Council Directive on the approximation of the laws of the Member States relating to electromagnetic compatibility (“the EMC Directive“) (89/336/EEC 3 as amended) and Directive 1999/5/EC of the European Parliament and of the

21、Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (“the R ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements“. 2 Directive 1999/5/EC of the European Par

22、liament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R Ground-based VHF hand-held, mobile and fixed radio transmitters, receivers and transceivers for the VHF aeronautical mobile service using amplitud

23、e modulation; Technical characteristics and methods of measurement“. ETSI ETSI EN 301 489-22 V1.3.1 (2003-11) 6 5 ITU Radio Regulations (1998). 6 ITU-T Recommendation P.53: “Psophometer for use on telephone-type circuits“. 7 Directive 98/34/EC of the European Parliament and of the Council of 22 June

24、 1998 laying down a procedure for the provision of information in the field of technical standards and regulations. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in EN 301 489-1 1, clause 3 and the following apply: base stat

25、ion: aeronautical radio equipment, used in the aeronautical mobile service, for use with an external antenna and intended for use at a fixed location centre frequency (Fc): centre of the transmitter necessary bandwidth integral antenna equipment: radio communications equipment with an antenna integr

26、ated into the equipment without the use of an external connector and considered to be part of the equipment NOTE: An integral antenna may be internal or external to the equipment. In equipment of this type, a 50 RF connection point shall be provided for test purposes. necessary bandwidth: for a give

27、n class of emission, the width of the frequency band which is just sufficient to ensure the transmission of information at the rate and with the quality required under specified conditions (ITU Radio Regulations, clause 146) occupied bandwidth: width of a frequency band such that, below the lower an

28、d above the upper frequency limits, the mean powers emitted are each equal to a specified percentage /2 of the total mean power of a given emission NOTE: Unless otherwise specified by ITU-R for the appropriate class of emission, the value of /2 should be taken as 0,5 % (ITU Radio Regulations 5). sim

29、plex: instantaneous one-way communications link product standard: functional standard describing frequency management parameters of radio product operating frequency range: range(s) of continuous radio frequencies covered by the Equipment Under Test (EUT) 3.2 Abbreviations For the purposes of the pr

30、esent document, the following abbreviations apply: AC Alternating Current AM Amplitude Modulation BER Bit Error Ratio BW BandWidthD8PSK Differentially encoded 8 Phase Shift Keying DC Direct Current DSB Double Side Band full carrier EM ElectroMagnetic EMC ElectroMagnetic Compatibility EUT Equipment U

31、nder Test Fc centre frequency GFSK Gaussian Frequency Shift Keying PEP Peak Envelope Power RF Radio Frequency rms root mean of squares ETSI ETSI EN 301 489-22 V1.3.1 (2003-11) 7 VDL VHF Digital Link VHF Very High Frequency 4 Test conditions For the purpose of the present document, the test condition

32、s of EN 301 489-1 1, clause 4 shall apply as appropriate. Further product related test conditions for VHF aeronautical radio equipment are specified in the present document. 4.1 General For emission and immunity tests the test modulation, test arrangements, etc., as specified in the present document

33、, clauses 4.2 to 4.5, shall apply. 4.2 Arrangements for test signals The provisions of EN 301 489-1 1, clause 4.2 shall apply with the following modification. For integral antenna radio communications equipment a 50 RF connection point shall be provided for connection to the measuring equipment. 4.2

34、.1 Arrangement for test signals at the input to the transmitter The provisions of EN 301 489-1 1, clause 4.2.1 shall apply with the following modification. The transmitter shall be modulated with normal test modulation by an internal or external signal source capable of producing the appropriate dri

35、ve signal (see clause 4.5). 4.2.2 Arrangements for test signals at the output from the transmitter The provisions of EN 301 489-1 1, clause 4.2.2 shall apply with the following modifications. The transmitter shall be operated at its maximum rated RF output (PEP), or at a level not less than -6 dB re

36、lative to that power level in the event of declared thermal limitations. The RF output signal of the transmitter shall be coupled to the measuring equipment via a shielded transmission line such as a coaxial cable. The measuring equipment shall comprise a combination of a modulation analyser and an

37、audio distortion meter. For transmitters with an integral antenna, a 50 RF connection point shall be provided for test purposes. 4.2.3 Arrangements for test signals at the input to the receiver The provisions of EN 301 489-1 1, clause 4.2.3 shall apply with the following modifications. The wanted RF

38、 input signal coupled to the receiver shall be modulated with normal test modulation (see clause 4.5). For receivers with an integral antenna, a 50 RF connection point shall be provided for test purposes. 4.2.4 Arrangements for test signals at the output from the receiver The provisions of EN 301 48

39、9-1 1, clause 4.2.4 shall apply. 4.2.5 Arrangements for testing transmitters and receivers together (as a system) The provisions of EN 301 489-1 1, clause 4.2.5 shall apply. ETSI ETSI EN 301 489-22 V1.3.1 (2003-11) 8 4.3 RF exclusion band for radio communications equipment The provisions of EN 301 4

40、89-1 1, clause 4.3 shall apply. Frequencies on which radio communications equipment is intended to operate are excluded from immunity tests with radiated RF test signals. The RF test exclusions are referred to as “exclusion bands“ and are detailed below for the various cases. 4.3.1 Transmitter exclu

41、sion bands for EM emission measurements Exclusion bands shall apply when measuring transmitters in transmit mode of operation. Exclusion bands shall not apply when measuring transmitters in standby mode of operation. The exclusion band for transmitters is given in table 1. Table 1: Transmitter exclu

42、sion bands for emission measurements Category of EUT (Channel spacing) Width of exclusion band (see notes 1 and 2) Centre of exclusion band 8,33 kHz equipment 2,042 MHz or 2,442 MHz Fc 25 kHz equipment 2,125 MHz or 2,525 MHz Fc NOTE 1: The exclusion band is the product of 5 times the receiver bandwi

43、dth plus 20 times the measurement bandwidth (i.e. 100 kHz, or 120 kHz), for the measurement range 30 MHz to 1 GHz. NOTE 2: The extension of the exclusion bandwidth for transmitters to include 20 times the measurement bandwidth is needed to accommodate the skirt bandwidth of the filters used in the m

44、easurement equipment. A narrower measurement bandwidth may be used. The exclusion band and measurement bandwidth shall be recorded in the test report. 4.3.2 Receiver exclusion bands for EM emission measurements There shall be no frequency exclusion band applied to EM emission measurements of receive

45、rs, or ancillaries. 4.3.3 Transmitter exclusion bands for immunity tests The exclusion band extends plus and minus twice the occupied bandwidth (BW) from the centre frequency (Fc 2BW). For 25 kHz equipment the exclusion band extends 50 kHz, and for 8,33 kHz equipment 16,7 kHz around the centre frequ

46、ency (Fc). 4.3.4 Receiver exclusion bands for immunity tests The exclusion band is the operating frequency range, extended at each end by 5 % of the centre frequency (Fc). EXAMPLE: For the centre frequency 127,5 MHz, the exclusion band extends from 111,625 MHz (i.e. 118 MHz minus 6,375 MHz) to 143,3

47、5 MHz (i.e. 136,975 MHz plus 6,375 MHz). 4.4 Narrow band responses of receivers Any receiver response to an RF immunity test that has a bandwidth as defined in EN 301 489-1 1, clause 4.4. shall be considered a narrow band response, and shall be subject to spurious response rejection tests specified

48、in the relevant product standards for the effective use of the radio spectrum. ETSI ETSI EN 301 489-22 V1.3.1 (2003-11) 9 4.5 Normal test modulation The normal test modulation is specified as follows: for analogue speech equipment: - the receiver input signal shall be set to the nominal operating fr

49、equency, modulated with a sinusoidal audio frequency of 1 kHz at 30 % depth and at a level which gives a SINAD ratio of 20 dB, measured at the receiver output using a psophometric telephone filtering network as described in ITU-T Recommendation P.53 6; - the transmitter shall be modulated with a sinusoidal audio frequency signal of 1 kHz. The level of this audio signal shall be set to obtain at least 80 % modulation depth of the RF output signal. for VDL Mode 2 and VDL Mode 4 equipment: - the receiver input signal shall be s

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1