1、 ETSI EN 301 841-3 V2.1.1 (2016-09) VHF air-ground Digital Link (VDL) Mode 2; Technical characteristics and methods of measurement for ground-based equipment; Part 3: Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI
2、ETSI EN 301 841-3 V2.1.1 (2016-09) 2 Reference REN/ERM-TGAERO-34 Keywords aeronautical, AM, DSB, harmonised standard, radio, testing, VHF ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Associati
3、on but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print ve
4、rsions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a s
5、pecific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If yo
6、u find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and mic
7、rofilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights
8、 reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and own
9、ed by the GSM Association. ETSI ETSI EN 301 841-3 V2.1.1 (2016-09) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions and abbreviations . 7g33.1 Definitions 7g33.2 Ab
10、breviations . 8g34 Technical requirements specifications . 8g34.1 Environmental profile . 8g34.2 Conformance requirements 9g34.2.1 Transmitter requirements 9g34.2.1.1 Frequency error . 9g34.2.1.1.1 Requirement 9g34.2.1.1.2 Conformance . 9g34.2.1.2 Manufacturers declared output power 9g34.2.1.2.1 Req
11、uirement 9g34.2.1.2.2 Conformance . 9g34.2.1.3 Adjacent channel power 9g34.2.1.3.1 Requirement 9g34.2.1.3.2 Conformance . 9g34.2.1.4 Transmitter Conducted spurious emissions . 9g34.2.1.4.1 Requirement 9g34.2.1.4.2 Conformance . 9g34.2.1.5 Transmitter Cabinet radiation 9g34.2.1.5.1 Requirement 9g34.2
12、.1.5.2 Conformance . 9g34.2.1.6 Void. 10g34.2.1.7 Intermodulation attenuation 10g34.2.1.7.1 Requirements. 10g34.2.1.7.2 Conformance . 10g34.2.1.8 Void. 10g34.2.1.9 RF power release time . 10g34.2.1.9.1 Requirement 10g34.2.1.9.2 Conformance . 10g34.2.1.10 Transient behaviour of the transmitter 10g34.
13、2.1.10.1 Receiver to transmitter turn-around time . 10g34.2.1.10.2 Transmitter to receiver turn-around time . 10g34.2.1.11 Modulation Accuracy - Symbol constellation error 10g34.2.1.11.1 Requirement 10g34.2.1.11.2 Conformance . 11g34.2.1.12 Load VSWR capability . 11g34.2.1.12.1 Requirement 11g34.2.1
14、.12.2 Conformance . 11g34.2.2 Receiver requirements 11g34.2.2.1 Sensitivity . 11g34.2.2.1.1 Requirement 11g34.2.2.1.2 Conformance . 11g34.2.2.2 Co-channel interference 11g34.2.2.2.1 Requirement 11g34.2.2.2.2 Conformance . 11g34.2.2.3 First adjacent channel rejection . 11g3ETSI ETSI EN 301 841-3 V2.1
15、.1 (2016-09) 4 4.2.2.3.1 Requirement 11g34.2.2.3.2 Conformance . 11g34.2.2.4 Spurious response rejection of signals within the VHF aeronautical band . 11g34.2.2.4.1 Requirement 11g34.2.2.4.2 Conformance . 12g34.2.2.5 Spurious response rejection of signals outside the VHF aeronautical band 12g34.2.2.
16、5.1 Requirement 12g34.2.2.5.2 Conformance . 12g34.2.2.6 In-band Intermodulation response rejection 12g34.2.2.6.1 Requirement 12g34.2.2.6.2 Conformance . 12g34.2.2.7 Blocking or desensitization . 12g34.2.2.7.1 Requirement 12g34.2.2.7.2 Conformance . 12g34.2.2.8 Receiver Conducted spurious emission .
17、12g34.2.2.8.1 Requirement 12g34.2.2.8.2 Conformance . 12g34.2.2.9 Receiver Cabinet radiation 12g34.2.2.9.1 Requirement 12g34.2.2.9.2 Conformance . 12g35 Testing for compliance with technical requirements 13g35.1 Environmental conditions for testing . 13g35.1.0 General 13g35.1.1 Test power source . 1
18、3g35.1.2 Normal and extreme test conditions 13g35.2 Interpretation of the measurement results 13g35.3 Conformance tests 14g35.3.1 Transmitter test specifications 14g35.3.1.1 Frequency error . 14g35.3.1.2 Manufacturers declared output power 14g35.3.1.3 Adjacent channel power 14g35.3.1.4 Conducted Spu
19、rious emissions 14g35.3.1.5 Cabinet Radiation 14g35.3.1.6 Void. 14g35.3.1.7 Inter-modulation attenuation . 15g35.3.1.8 Void. 15g35.3.1.9 RF power release time . 15g35.3.1.10 Transient behaviour of the transmitter 15g35.3.1.10.1 Receiver to transmitter turn-around time . 15g35.3.1.10.2 Transmitter to
20、 receiver turn-around time . 15g35.3.1.11 Modulation accuracy - Symbol constellation error . 15g35.3.1.12 Load VSWR capability . 15g35.3.2 Receiver test specifications . 15g35.3.2.1 Sensitivity . 15g35.3.2.2 Co-channel interference 15g35.3.2.3 First Adjacent channel rejection 15g35.3.2.4 Spurious re
21、sponse rejection of signals within the VHF aeronautical band . 15g35.3.2.5 Spurious response rejection of signals outside the VHF aeronautical band 15g35.3.2.6 In-band Intermodulation rejection . 15g35.3.2.7 Blocking or desensitization . 15g35.3.2.8 Conducted spurious emission 16g35.3.2.9 Cabinet Ra
22、diation 16g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 17g3Annex B (informative): Bibliography . 19g3History 20g3ETSI ETSI EN 301 841-3 V2.1.1 (2016-09) 5 Intellectual Property Rights IPRs essential or potentially essential
23、 to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified t
24、o ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the
25、 existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and R
26、adio spectrum Matters (ERM). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.4 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating t
27、o the making available on the market of radio equipment and repealing Directive 1999/5/EC i.1. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the l
28、imits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 3 of a multi-part deliverable covering VHF air-ground Digital Link (VDL) Mode 2; Technical characteri
29、stics and methods of measurement for ground-based equipment, as identified below: Part 1: “Physical layer and MAC sub-layer“; Part 2: “Upper layers“; Part 3: “Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU“. National transposition dates Date of ado
30、ption of this EN: 13 September 2016 Date of latest announcement of this EN (doa): 31 December 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 30 June 2017 Date of withdrawal of any conflicting National Standard (dow): 30 June 2018 Modal verbs terminology I
31、n the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI de
32、liverables except when used in direct citation. ETSI ETSI EN 301 841-3 V2.1.1 (2016-09) 6 1 Scope The present document applies to VDL Mode 2 ground-air digital communications using Differential Eight Phase Shift Keying (D8PSK), intended for channel increments of 25 kHz. The VDL Mode 2 system provide
33、s data communication exchanges between aircraft and ground-based systems, operating in the VHF band (117,975 MHz to 137,000 MHz). The scope of the present document is limited to ground based stations. NOTE: The VDL Mode 2 can be used as an Air/Ground sub-network of the Aeronautical Telecommunication
34、 Network (ATN) using a band with AM(R)S spectrum allocation. The present document contains requirements to demonstrate that “. Radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference“ i.1. In additi
35、on to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the Directive 2014/53/EU i.1 as well as essential requirements under the SES Interoperability Regulation No 552/2004 i.5 and related implementing rules and
36、/or essential requirements under the EASA basic Regulation No 216/2008 i.6 as amended by Regulation No 1108/2009 i.7 may apply to equipment within the scope of the present document. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition
37、 number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected locati
38、on might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 ETSI EN 301
39、841-1 (V1.4.1) (04-2015): “VHF air-ground Digital Link (VDL) Mode 2; Technical characteristics and methods of measurement for ground-based equipment; Part 1: Physical layer and MAC sub-layer“. 2 ETSI EN 300 113-1 (V1.7.1) (11-2011): “Electromagnetic compatibility and Radio spectrum Matters (ERM); La
40、nd mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector; Part 1: Technical characteristics and methods of measurement“. 2.2 Informative references References are either specific (ident
41、ified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this c
42、lause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Directive 2014/53/EU of the European Pa
43、rliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. ETSI ETSI EN 301 841-3 V2.1.1 (2016-09) 7 i.2 ETSI TR 100 028-1: “Electromagnetic compatibility and
44、Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 1“. i.3 ETSI TR 100 028-2: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 2“. i.4 Commissi
45、on Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and
46、of the Council. i.5 Regulation (EC) No 552/2004 of the European Parliament and of the Council of 10 March 2004 on the interoperability of the European Air Traffic Management network (interoperability Regulation), OJ L 96, 31.03.2004, p. 26 as amended by Regulation (EC) No 1070/2009, OJ L 300, 14.11.
47、2009, p. 34. i.6 Regulation (EC) No 216/2008 of the European Parliament and of the Council of 20 February 2008 on common rules in the field of civil aviation and establishing a European Aviation Safety Agency, and repealing Council Directive 91/670/EEC, Regulation (EC) No 1592/2002 and Directive 200
48、4/36/EC. i.7 Regulation (EC) No 1108/2009 of the European Parliament and of the Council of 21 October 2009 amending Regulation (EC) No 216/2008 in the field of aerodromes, air traffic management and air navigation services and repealing Directive 2006/23/EC. 3 Definitions and abbreviations 3.1 Defin
49、itions For the purposes of the present document, the terms and definitions given in Directive 2014/53/EU i.1 and the following apply: adjacent channel power: amount of the modulated RF signal power transmitted outside of the assigned channel NOTE: Adjacent channel power includes discrete spurious, signal sidebands, and noise density (including phase noise) at the transmitter output. adjacent channel rejection: receivers ability to demodulate the desired signal and meet the uncorrected BER requirement in the presence of an interfering sign
