1、 ETSI EN 301 843-1 V2.2.1 (2017-11) ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services; Harmonised Standard for electromagnetic compatibility; Part 1: Common technical requirements HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 843-1 V2.2.1 (2017-11) 2 Reference REN/
2、ERM-EMC-385 Keywords EMC, harmonised standard, maritime, radio, regulation ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06)
3、 N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without th
4、e prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the pre
5、sent document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment
6、 to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The
7、content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI registered for the benefit
8、of its Members. 3GPPTM and LTE are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM and the GSM logo are trademarks registered and owned by the GSM Association. ETSI ETSI EN 301 843-1 V2
9、.2.1 (2017-11) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 6g31 Scope 7g32 References 8g32.1 Normative references . 8g32.2 Informative references 8g33 Definitions, symbols and abbreviations . 9g33.1 Definitions 9g33.2 Symbols 10g33.3 Abbreviations . 10g34 General
10、 and operational requirements 11g34.1 Environmental profile . 11g34.2 Arrangements for test signals . 11g34.2.0 General 11g34.2.1 Arrangements for test signals at the input of transmitters . 11g34.2.2 Arrangements for test signals at the output of transmitters . 12g34.2.3 Arrangements for test signa
11、ls at the input of receivers . 12g34.2.4 Arrangements for test signals at the output of receivers . 12g34.2.5 Arrangements for testing transmitter and receiver together (as a system) 13g34.3 RF exclusion band of radio communications equipment 13g34.4 Narrow band responses of receivers or receivers w
12、hich are part of transceivers . 14g34.5 Normal test modulation 14g35 Performance assessment . 14g35.1 General . 14g35.2 Equipment which can provide a continuous communication link 15g35.3 Equipment which does not provide a continuous communication link 15g35.4 Ancillary equipment . 16g35.5 Equipment
13、 classification 16g36 Performance criteria . 17g36.0 General requirements . 17g36.1 Performance criteria A for continuous phenomena applied to transmitters and receivers 17g36.2 Performance criteria B for transient phenomena applied to transmitters and receivers . 17g36.3 Performance criteria C appl
14、ied to power supply failure . 18g36.4 Performance check . 18g36.5 Performance criteria for equipment which does not provide a continuous communication link 18g36.6 Performance criteria for ancillary equipment tested on a stand alone basis . 18g37 Applicability overview tables . 19g37.0 General . 19g
15、37.1 EMC emission 19g37.2 Immunity 19g38 Testing for compliance with technical requirements 20g38.0 Environmental conditions for testing . 20g38.1 Test configuration. 20g38.2 Enclosure of ancillary equipment measured on a stand alone basis . 20g38.2.0 Applicability . 20g38.2.1 Test description . 21g
16、38.2.2 Test method 21g38.2.3 Limits 21g38.3 DC power input/output ports 22g38.3.0 Applicability . 22g38.3.1 Test description . 22g3ETSI ETSI EN 301 843-1 V2.2.1 (2017-11) 4 8.3.2 Test method 22g38.3.3 Limits 23g38.4 AC mains power input/output ports . 23g38.4.0 Applicability . 23g38.4.1 Test descrip
17、tion . 23g38.4.2 Test method 23g38.4.3 Limits 24g39 Test methods and levels for immunity tests . 24g39.0 General . 24g39.1 Test configuration. 24g39.2 Radio frequency electromagnetic field (80 MHz to 2 700 MHz) . 25g39.2.0 Applicability . 25g39.2.1 Test description . 25g39.2.2 Test method 25g39.2.3
18、Performance criteria 25g39.3 Electrostatic discharge 26g39.3.0 Applicability . 26g39.3.1 Test description . 26g39.3.2 Test method 26g39.3.3 Performance criteria 26g39.4 Fast transients, differential and common mode 26g39.4.0 Applicability . 26g39.4.1 Test description . 27g39.4.2 Test method 27g39.4.
19、3 Performance criteria 27g39.5 Radio frequency, common mode 27g39.5.0 Applicability . 27g39.5.1 Test description . 27g39.5.2 Test method 28g39.5.3 Performance criteria 28g39.6 Power supply variations . 28g39.6.0 Applicability . 28g39.6.1 Power supply short term variations . 28g39.6.1.1 Test descript
20、ion . 28g39.6.1.2 Test method . 29g39.6.1.3 Performance criteria 29g39.6.2 Power supply failure . 29g39.6.2.1 Test description . 29g39.6.2.2 Test method . 29g39.6.2.3 Performance criteria 29g39.7 Surges . 29g39.7.0 Applicability . 29g39.7.1 Test description . 29g39.7.2 Test method 30g39.7.3 Performa
21、nce criteria 30g3Annex A (informative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 31g3Annex B (informative): Bibliography . 33g3Annex C (informative): Change history . 34g3History 35g3ETSI ETSI EN 301 843-1 V2.2.1 (2017-11) 5 Intellectual Prop
22、erty Rights Essential patents IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Propert
23、y Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR search
24、es, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/o
25、r tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not
26、 constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prep
27、ared under the Commissions standardisation request C(2015) 5376 final i.10 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and re
28、pealing Directive 1999/5/EC i.4. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of c
29、onformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 1 of a multi-part deliverable covering the ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services, as identified below: Part 1: “Comm
30、on technical requirements“; Part 2: “Specific conditions for VHF radiotelephone transmitters and receivers“; Part 4: “Specific conditions for Narrow-Band Direct-Printing (NBDP) NAVTEX receivers“; Part 5: “Specific conditions for MF/HF radiotelephone transmitters and receivers“; Part 6: “Specific con
31、ditions for Earth Stations on board Vessels operating in frequency bands above 3 GHz“. Part 7: “Specific conditions for Maritime Broadband Radiolink equipment“. ETSI ETSI EN 301 843-1 V2.2.1 (2017-11) 6 National transposition dates Date of adoption of this EN: 17 October 2017 Date of latest announce
32、ment of this EN (doa): 31 January 2018 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 July 2018 Date of withdrawal of any conflicting National Standard (dow): 31 July 2019 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “shou
33、ld not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN
34、 301 843-1 V2.2.1 (2017-11) 7 1 Scope The present document contains the common requirements for marine radio communications equipment and associated ancillary equipment, in respect of ElectroMagnetic Compatibility (EMC). The provisions of the present document apply to marine radio equipment not cove
35、red in the scope of the Council Directive on marine equipment (the “Marine Equipment Directive“ 96/98/EC i.5). Product dependent arrangements necessary to perform the EMC tests on dedicated types of marine radio communications equipment, and the assessment of test results, are detailed in the approp
36、riate product related parts of the present document. The present document, together with the product related part, specifies the applicable EMC tests, the methods of measurement, the limits and the performance criteria for marine radio equipment and associated ancillary equipment. In case of differe
37、nces (for instance concerning special conditions, definitions, abbreviation) between the present document and the relevant product related part of the present document, the product related part takes precedence. For the further content of the present document, the expression “radio equipment“ is tak
38、en to mean marine radio communications equipment, in each individual case. Technical specifications related to the antenna port of radio equipment and emissions from the enclosure port of radio equipment and combinations of radio and associated ancillary equipment are not included in the present doc
39、ument. Such technical specifications are normally found in the relevant product standards for the effective use of the radio spectrum. The environment classification used in the present document is maritime, as defined in IEC EN 60945 1. Marine radio communications equipment meeting the EMC requirem
40、ents set out in IEC EN 60945 1 is deemed to meet also the EMC requirements for the residential, commercial and light industrial environment as defined in IEC EN 61000-6-3 i.1 and IEC EN 61000-6-1 i.2. The EMC requirements have been selected to ensure an adequate level of compatibility for apparatus
41、intended to be used in the maritime environment. The levels, however, do not cover extreme cases which may occur in any location but with low probability of occurrence. Compliance of radio equipment to the requirements of the present document does not signify compliance to any requirements related t
42、o spectrum management or to the use of the equipment (licensing requirements). Compliance to the requirements of the present document does not signify compliance to any safety requirements. However, it is the responsibility of the assessor of the equipment to record in the test report any observatio
43、ns regarding the test sample becoming dangerous or unsafe as a result of the application of the tests called for in the present document. NOTE: The relationship between the present document and essential requirements of article 3.1b of Directive 2014/53/EU i.4 is given in annex A. In addition to the
44、 present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the Radio Equipment Directive i.4 may apply to equipment within the scope of the present document. ETSI ETSI EN 301 843-1 V2.2.1 (2017-11) 8 2 References 2.1 Normat
45、ive references References are specific, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicly available in the expected location might be found at https:/docbox.etsi.org/Reference/. NOTE: Whi
46、le any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 IEC EN 60945 (2002) + Corrigendum 1 (2008): “Maritime navigation and radioc
47、ommunication equipment and systems - General requirements - Methods of testing and required test results“. 2 CISPR 16-1-1 (2015): “Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus“. 3
48、 IEC EN 61000-4-2 (2008): “Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test“. 4 IEC EN 61000-4-3 (2006 + Amendment 1:2007 +Amendment 2:2010): “Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques
49、- Radiated, radio-frequency, electromagnetic field immunity test“. 5 IEC EN 61000-4-4 (2012): “Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test“. 6 IEC EN 61000-4-5 (2014): “Electromagnetic compatibility (EMC) - Part 4-5: Testing and measurement techniques - Surge immunity test“. 7 IEC EN 61000-4-6 (2013): “Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields“. 2
