1、 ETSI EN 301 843-5 V2.2.1 (2017-11) ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services; Harmonised Standard for electromagnetic compatibility; Part 5: Specific conditions for MF/HF radiotelephone transmitters and receivers HARMONISED EUROPEAN STANDARD ETSI ETSI EN 3
2、01 843-5 V2.2.1 (2017-11) 2 Reference REN/ERM-EMC-388 Keywords EMC, harmonised standard, HF, maritime, MF, radio, receiver, regulation ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association
3、but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versi
4、ons of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a spec
5、ific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you f
6、ind errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microf
7、ilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the
8、ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM and the GSM logo are trademarks registered
9、 and owned by the GSM Association. ETSI ETSI EN 301 843-5 V2.2.1 (2017-11) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions, symbols and abbreviations . 7g33.1 Defi
10、nitions 7g33.2 Symbols 7g33.3 Abbreviations . 7g34 General and operational requirements 8g34.1 Environmental profile . 8g34.2 Arrangements for test signals . 8g34.2.0 General 8g34.2.1 Arrangements for test signals at the input of the transmitter 8g34.2.2 Arrangements for test signals at the output o
11、f the transmitter 8g34.2.3 Arrangements for test signals at the input of the receiver . 8g34.2.4 Arrangements for test signals at the output of the receiver . 8g34.2.5 Arrangements for testing transmitter and receiver together (as a system) 8g34.3 Exclusion bands 9g34.3.0 General 9g34.3.1 Exclusion
12、bands for receivers and receiver parts of transceivers 9g34.3.2 Exclusion band for transmitters 9g34.4 Narrow band responses on receivers 9g34.5 Normal test modulation 9g34.6 Artificial Antennae (non-radiating test load) 10g35 Performance assessment . 10g35.1 General . 10g35.2 Equipment which can pr
13、ovide a continuous communication link 10g35.3 Equipment which does not provide a continuous communication link 10g35.4 Ancillary equipment . 11g35.5 Equipment classification 11g36 Performance criteria . 11g36.0 General . 11g36.1 Performance criteria A for continuous phenomena applied to transmitters
14、 and receivers 11g36.2 Performance criteria B for transient phenomena applied to transmitters and receivers . 11g36.3 Performance criteria C applied to power supply failure . 11g36.4 Performance check . 11g36.4.0 General 11g36.4.1 Transmitter 11g36.4.2 Receiver 12g36.5 Performance criteria for equip
15、ment which does not provide a continuous communication link 12g36.6 Performance criteria for ancillary equipment tested on a stand-alone basis . 12g37 Applicability overview . 12g37.1 Emission . 12g37.1.1 General 12g37.1.2 Special conditions . 12g37.2 Immunity 12g37.2.1 General 12g37.2.2 Special con
16、ditions . 13g3ETSI ETSI EN 301 843-5 V2.2.1 (2017-11) 4 Annex A (informative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 14g3Annex B (informative): Examples of types of MF/HF marine radiotelephone equipment in the scope of the present document
17、 16g3B.1 Radiotelephone transmitters and receivers for the maritime mobile service operating in the MF/HF bands 16g3Annex C (informative): Change history . 17g3History 18g3ETSI ETSI EN 301 843-5 V2.2.1 (2017-11) 5 Intellectual Property Rights Essential patents IPRs essential or potentially essential
18、 to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified t
19、o ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the
20、 existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ET
21、SI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizat
22、ions associated with those trademarks. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final
23、 i.4 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.1. Once the present document is cited in
24、 the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Direct
25、ive, and associated EFTA regulations. The present document is part 5 of a multi-part deliverable. Full details of the entire series can be found in part 1 1. National transposition dates Date of adoption of this EN: 17 October 2017 Date of latest announcement of this EN (doa): 31 January 2018 Date o
26、f latest publication of new National Standard or endorsement of this EN (dop/e): 31 July 2018 Date of withdrawal of any conflicting National Standard (dow): 31 July 2019 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not
27、“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 301 843-5 V2.2.1 (2017-11) 6 1 Scope The pre
28、sent document together with ETSI EN 301 843-1 1, covers the assessment of MF/HF radiotelephone transmitters and receivers for the maritime mobile service, and ancillary equipment in respect of ElectroMagnetic Compatibility (EMC). Technical specifications related to the antenna port and emissions fro
29、m the enclosure port of marine radiotelephone transmitters and receivers are not included in the present document. Such technical specifications are found in the related product standards for the effective use of the radio spectrum. The present document specifies the applicable test conditions, perf
30、ormance assessment, and performance criteria for radiotelephone transmitters and receivers for the maritime mobile service and the associated ancillary equipment. Examples of types of MF/HF radiotelephone transmitters and receivers for the maritime mobile service covered by the present document are
31、given in annex A. In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present document and ETSI EN 301 843-1 1, the provisions of the present document take precedence. The electromagnetic environment used in the present document to develop the
32、technical specifications encompasses the electromagnetic environment on-board ships as identified in IEC EN 60945 i.3. NOTE: The relationship between the present document and essential requirements of article 3.1b of Directive 2014/53/EU i.1 is given in annex A. 2 References 2.1 Normative references
33、 References are specific, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicly available in the expected location might be found at https:/docbox.etsi.org/Reference/. NOTE: While any hyperli
34、nks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 ETSI EN 301 843-1 (V2.2.1) (11-2017): “ElectroMagnetic Compatibility (EMC) standard for m
35、arine radio equipment and services; Harmonised Standard for electromagnetic compatibility; Part 1: Common technical requirements“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific refer
36、ences, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The followin
37、g referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relati
38、ng to the making available on the market of radio equipment and repealing Directive 1999/5/EC. ETSI ETSI EN 301 843-5 V2.2.1 (2017-11) 7 i.2 ETSI EN 303 402 (V2.1.1): “Maritime mobile transmitters and receivers for use in the MF and HF bands; Harmonised Standard covering the essential requirements o
39、f articles 3.2 and 3.3(g) of Directive 2014/53/EU“. i.3 IEC EN 60945 (2002) + Corrigendum 1 (2008): “Maritime navigation and radiocommunication equipment and systems - General requirements - Methods of testing and required test results“. i.4 Commission Implementing Decision C(2015) 5376 final of 4.8
40、.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. 3 Definitions, symbols and abbrevi
41、ations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI EN 301 843-1 1 and the following apply: standard output power (audio): (of the receiver) is defined as: a) 1 mW for earphone reception; b) 500 mW for loudspeaker reception; c) 0 dBm (1 mW) into 6
42、00 for the audio line outputs. 3.2 Symbols For the purposes of the present document, the following symbols apply: emf electromotive force rms root mean square SINAD (Signal + Noise + Distortion) / (Noise + Distortion) 3.3 Abbreviations For the purposes of the present document, the abbreviations give
43、n in ETSI EN 301 843-1 1 and the following apply: AGC Automatic Gain Control DSC Digital Selective Calling EMC ElectroMagnetic Compatibility EUT Equipment Under Test F1B Frequency modulation NOTE: Single channel containing quantized or digital information with the use of a modulating sub-carrier, te
44、legraphy for automatic reception. HF High Frequency J3E Single Sideband NOTE: Suppressed carrier, single channel containing analogue information, telephony. MF Medium Frequency MF/HF Medium Frequency/High Frequency PEP Peak Envelope Power RF Radio Frequency ETSI ETSI EN 301 843-5 V2.2.1 (2017-11) 8
45、4 General and operational requirements 4.1 Environmental profile The provisions of ETSI EN 301 843-1 1, clause 4.1 shall apply with the following modifications. For emission and immunity tests the normal test modulation, test arrangements, etc., as specified in the present document, clauses 4.1 to 4
46、.5, shall apply. The test shall be carried out at a point within the specified normal operating environmental range of temperature and humidity with the equipment connected to the normal power supply voltage. 4.2 Arrangements for test signals 4.2.0 General The provisions of ETSI EN 301 843-1 1, clau
47、se 4.2 shall apply. 4.2.1 Arrangements for test signals at the input of the transmitter The provisions of ETSI EN 301 843-1 1, clause 4.2.1 shall apply. 4.2.2 Arrangements for test signals at the output of the transmitter The provisions of ETSI EN 301 843-1 1, clause 4.2.2 shall apply. 4.2.3 Arrange
48、ments for test signals at the input of the receiver The provisions of ETSI EN 301 843-1 1, clause 4.2.3 shall apply with the following modifications. The wanted RF input signal, coupled to the receiver, shall be modulated with normal test modulation as specified for that type of equipment (see claus
49、e 4.5). The level of the wanted signal shall be as follows: MF (1 605 kHz to 4 000 kHz) J3E Mode: +56 dBuV F1B Mode: +45 dBuV. HF (4 MHz to 27,5 MHz) J3E Mode: +51 dBuV F1B Mode: +40 dBuV. Measurements shall only be made in F1B mode where the EUT does not have J3E mode. 4.2.4 Arrangements for test signals at the output of the receiver The provisions of ETSI EN 301 843-1 1, clause 4.2.4 shall apply as appropriate. 4.2.5 Arrangements for testing transmitter and receiver together (as a system) The provisions of ETSI EN 301 843-1 1
