1、 ETSI EN 302 454-2 V1.2.1 (2015-10) Meteorological Aids (Met Aids); Radiosondes to be used in the 1 668,4 MHz to 1 690 MHz frequency range; Part 2: Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 302 454-2 V
2、1.2.1 (2015-10) 2 Reference REN/ERM-JTFEA-24 Keywords radio, regulation, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grass
3、e (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified with
4、out the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of t
5、he present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to
6、one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The cont
7、ent of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2015. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade M
8、arks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 302 454-2 V1.2.1 (2015-10)
9、3 Contents Intellectual Property Rights 4g3Foreword . 4g3Modal verbs terminology 4g3Executive summary 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions, symbols and abbreviations . 6g33.1 Definitions 6g33.2 Symbols 6g33.3 Abbreviations . 7g34 Tec
10、hnical requirements specifications . 7g34.1 Environmental profile . 7g34.2 Conformance requirements 7g34.2.1 Transmitter requirements 7g34.2.1.1 Frequency error . 7g34.2.1.2 Carrier power (conducted) 7g34.2.1.3 Effective radiated power . 7g34.2.1.4 Modulation bandwidth 7g34.2.1.5 Spurious emissions
11、7g34.2.1.6 Frequency stability under low-voltage conditions 7g35 Testing for compliance with technical requirements 8g35.1 Environmental conditions for testing . 8g35.1.1 Normal and extreme test-conditions . 8g35.1.2 Test power source . 8g35.2 Interpretation of the measurement results 8g35.3 Radio t
12、est suites 8g35.3.1 Transmitter test specifications 8g35.3.1.1 Frequency error . 8g35.3.1.2 Carrier power (conducted) 8g35.3.1.3 Effective radiated power . 9g35.3.1.4 Modulation bandwidth 9g35.3.1.5 Spurious emissions 9g35.3.1.6 Frequency stability under low-voltage conditions 9g3Annex A (normative)
13、: Relationship between the present document and the essential requirements of Directive 2014/53/EU . 10g3History 11g3ETSI ETSI EN 302 454-2 V1.2.1 (2015-10) 4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
14、pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Se
15、cretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates
16、on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared in repl
17、y to the Commissions standardisation request Commission Implementing Decision C(2015) 5376 final of 04.08.2015 to provide a means of conforming to the essential requirements of Directive 2014/53/EU on “the harmonisation of the laws of the Member States relating to the making available on the market
18、of radio equipment“ - also known as the Radio Equipment Directive i.1. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of th
19、e present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 2 of a multi-part deliverable covering digitally modulated Radiosonde transmitters in the Meteorological Aids frequency band
20、from 1 668,4 MHz to 1 690 MHz, as identified below: Part 1: “Technical characteristics and test methods“; Part 2: “Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU“. National transposition dates Date of adoption of this EN: 22 October 2015 Date of la
21、test announcement of this EN (doa): 31 January 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 July 2016 Date of withdrawal of any conflicting National Standard (dow): 31 July 2017 Modal verbs terminology In the present document “shall“, “shall not“, “s
22、hould“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation.
23、 ETSI ETSI EN 302 454-2 V1.2.1 (2015-10) 5 Executive summary The present document contains Conformance requirements for Meteorological Aids (Radiosondes) to be used in the 1 668,4 to 1 690 MHz frequency range. These requirements are defined for frequency error, carrier power, effective radiated powe
24、r, modulation bandwidth, spurious emissions and frequency stability under low voltage conditions. ETSI ETSI EN 302 454-2 V1.2.1 (2015-10) 6 1 Scope The present document applies to Radiosondes in the Meteorological Aids service to be used in the 1 668,4 MHz to 1 690 MHz frequency range. The present d
25、ocument contains requirements to demonstrate that “. Radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference“ i.1. 2 References 2.1 Normative references References are either specific (identified by
26、 date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be public
27、ly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of t
28、he present document. 1 ETSI EN 302 454-1 (V1.2.1) (10-2015): “Meteorological Aids (Met Aids); Radiosondes to be used in the 1 668,4 MHz to 1 690 MHz frequency range; Part 1: Technical characteristics and test methods“. 2.2 Informative references References are either specific (identified by date of
29、publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid
30、at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Directive 2014/53/EU of the European Parliament and of t
31、he Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.2 ETSI TR 100 028-2 (V1.4.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the
32、 measurement of mobile radio equipment characteristics; Part 2“. i.3 ETSI TR 100 028 (all parts) (V1.4.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics“. 3 Definitions, symbols and abbreviations 3.1 Defini
33、tions For the purposes of the present document, the terms and definitions given in the Radio Equipment Directive i.1 and ETSI EN 302 454-1 1 apply. 3.2 Symbols For the purposes of the present document, the symbols given in ETSI EN 302 454-1 1 apply. ETSI ETSI EN 302 454-2 V1.2.1 (2015-10) 7 3.3 Abbr
34、eviations For the purposes of the present document, the abbreviations given in ETSI EN 302 454-1 1 apply. 4 Technical requirements specifications 4.1 Environmental profile The technical requirements of the present document apply under the environmental profile for operation of the equipment, which s
35、hall be declared by the supplier. The equipment shall comply with all the technical requirements of the present document at all times when operating within the boundary limits of the declared operational environmental profile. 4.2 Conformance requirements 4.2.1 Transmitter requirements 4.2.1.1 Frequ
36、ency error The frequency error, as defined in ETSI EN 302 454-1 1, clause 7.2.1, shall not exceed the limits given in ETSI EN 302 454-1 1, clause 7.2.3. In order to assess compliance the test procedure in clause 5.3.1.1 shall be done. 4.2.1.2 Carrier power (conducted) The carrier power (conducted),
37、as defined in ETSI EN 302 454-1 1, clause 7.3.1, shall not exceed the limits in ETSI EN 302 454-1 1, clause 7.3.3. NOTE: This requirement applies to transmitters, which may be used without an integral or dedicated antenna. In order to assess compliance the test procedure in clause 5.3.1.2 shall be d
38、one. 4.2.1.3 Effective radiated power The effective radiated power, as defined in ETSI EN 302 454-1 1, clause 7.4.1, shall not exceed the limits given in ETSI EN 302 454-1 1, clause 7.4.3. NOTE: This requirement applies to transmitters with an integral or dedicated antenna. In order to assess compli
39、ance the test procedure in clause 5.3.1.3 shall be done. 4.2.1.4 Modulation bandwidth The modulation bandwidth, as defined in ETSI EN 302 454-1 1, clause 7.5.1, shall not exceed the limits in ETSI EN 302 454-1 1, clause 7.5.3. In order to assess compliance the test procedure in clause 5.3.1.4 shall
40、be done. 4.2.1.5 Spurious emissions The spurious emissions, as defined in ETSI EN 302 454-1 1, clause 7.6.1, shall not exceed the limits given in ETSI EN 302 454-1 1, clause 7.6.3. In order to assess compliance the test procedure in clause 5.3.1.5 shall be done. 4.2.1.6 Frequency stability under low
41、-voltage conditions The frequency stability under low-voltage conditions, as defined in ETSI EN 302 454-1 1, clause 7.7.1, shall comply conditions given in ETSI EN 302 454-1 1, clause 7.7.3. In order to assess compliance the test procedure in clause 5.3.1.6 shall be done. ETSI ETSI EN 302 454-2 V1.2
42、.1 (2015-10) 8 5 Testing for compliance with technical requirements 5.1 Environmental conditions for testing 5.1.1 Normal and extreme test-conditions Tests shall be made under normal test conditions, and also, where stated, under extreme test conditions. The test procedures shall be as specified in
43、ETSI EN 302 454-1 1, clauses 5.3 to 5.4. 5.1.2 Test power source The test power source shall meet the requirements of ETSI EN 302 454-1 1, clause 5.2. 5.2 Interpretation of the measurement results The interpretation of the results recorded in a test report for the measurements described in the prese
44、nt document shall be as follows: the measured value related to the corresponding limit will be used to decide whether an equipment meets the requirements of the present document; the value of the measurement uncertainty for the measurement of each parameter shall be included in the test report; the
45、recorded value of the measurement uncertainty shall be, for each measurement, equal to or lower than the figures in table 1. For the test methods, according to the present document, the measurement uncertainty figures shall be calculated and shall correspond to an expansion factor (coverage factor)
46、k = 1,96 or k = 2 (which provide confidence levels of respectively 95 % and 95,45 % in the case where the distributions characterizing the actual measurement uncertainties are normal (Gaussian). Principles for the calculation of measurement uncertainty are contained in ETSI TR 100 028 i.3, in partic
47、ular in annex D of the ETSI TR 100 028-2 i.2. Table 1 is based on such expansion factors. Table 1: Measurement uncertainty: maximum values Parameter Uncertainty RF frequency 1 10-7RF power, conducted 2,5 dB Radiated emission of transmitter, valid up to 12,75 GHz 6 dB Conducted emission of transmitte
48、r, valid up to 12,75 GHz 4 dB Temperature 1 C Relative Humidity 10 %RH Voltage (DC) 1 % 5.3 Radio test suites 5.3.1 Transmitter test specifications 5.3.1.1 Frequency error The test procedure is specified in ETSI EN 302 454-1 1, clause 7.2. 5.3.1.2 Carrier power (conducted) The test procedure is spec
49、ified in ETSI EN 302 454-1 1, clause 7.3. ETSI ETSI EN 302 454-2 V1.2.1 (2015-10) 9 5.3.1.3 Effective radiated power The test procedure is specified in ETSI EN 302 454-1 1, clause 7.4. 5.3.1.4 Modulation bandwidth The test procedure is specified in ETSI EN 302 454-1 1, clause 7.5. 5.3.1.5 Spurious emissions The test procedure is specified in ETSI EN 302 454-1 1, clause 7.6. 5.3.1.6 Frequency stability under low-voltage conditions The test procedure is specified in ETSI EN 302 454-1 1, clause 7.7
