1、 ETSI EN 302 608 V2.1.1 (2017-11) Short Range Devices (SRD); Radio equipment for Eurobalise railway systems; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 302 608 V2.1.1 (2017-11) 2 Reference REN/ERM-TG28-520
2、Keywords harmonised standard, radio, railways, SRD, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Impo
3、rtant notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written
4、 authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document s
5、hould be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the
6、following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the
7、PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
8、 3GPPTM and LTE are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM and the GSM logo are trademarks registered and owned by the GSM Association. ETSI ETSI EN 302 608 V2.1.1 (2017-11) 3
9、Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Introduction 6g31 Scope 7g32 References 7g32.1 Normative references . 7g32.2 Informative references 8g33 Definitions, symbols and abbreviations . 8g33.1 Definitions 8g33.2 Symbols 9g33.3 Abbreviations . 9g34 Technical
10、Requirements Specifications . 9g34.1 Environmental Profile 9g34.2 Transmitter Conformance Requirements 10g34.2.1 OBE TX Field Strength and Transmitter Mask 10g34.2.1.1 Applicability 10g34.2.1.2 Limits 10g34.2.1.3 Conformance . 10g34.2.1.4 Maximum Allowable Measurement Uncertainty 10g34.2.2 OBE Unwan
11、ted Emission . 10g34.2.2.1 Applicability 10g34.2.2.2 Limits 10g34.2.2.3 Conformance . 11g34.2.2.4 Maximum Allowable Measurement Uncertainty 11g34.2.3 Eurobalise TX Field Strength and Transmitter Mask . 11g34.2.3.1 Applicability 11g34.2.3.2 Limits 11g34.2.3.3 Conformance . 12g34.2.3.4 Maximum Allowab
12、le Measurement Uncertainty 12g34.2.4 Eurobalise Unwanted Emission 12g34.2.4.1 Applicability 12g34.2.4.2 Limits 12g34.2.4.3 Conformance . 12g34.2.4.4 Maximum Allowable Measurement Uncertainty 12g34.3 Receiver Conformance Requirements 13g34.3.1 OBE Receiver Sensitivity . 13g34.3.1.1 Applicability 13g3
13、4.3.1.2 Limits 13g34.3.1.3 Conformance . 13g34.3.2 OBE Receiver Blocking 13g34.3.2.1 Applicability 13g34.3.2.2 Limits 13g34.3.2.3 Conformance . 13g35 Testing for Compliance with Technical Requirements 13g35.1 Environmental Conditions for Testing . 13g35.2 General Conditions for Testing 14g35.2.1 Tes
14、t Conditions. 14g35.2.2 Test Power Source 14g35.2.3 Nominal Test Conditions 14g35.2.3.1 Normal Temperature and Humidity 14g35.2.3.2 Normal Test Power Source, Mains Voltage 14g35.2.3.3 Normal Test Power Source, Other Power Sources 14g3ETSI ETSI EN 302 608 V2.1.1 (2017-11) 4 5.2.4 Requirements for Tes
15、t Modulation . 14g35.2.5 Choice of Equipment 15g35.2.6 Measuring Receiver 15g35.3 Interpretation of the Measurement Results . 15g36 Performance Test Suites . 16g36.1 Conformance Methods of Measurement for Transmitter . 16g36.1.1 OBE TX Field Strength and Transmitter Mask 16g36.1.2 OBE Unwanted Emiss
16、ion . 16g36.1.3 Eurobalise Tx Field Strength and Transmitter Mask 17g36.1.4 Eurobalise Unwanted Emission 17g36.2 Conformance Methods of Measurement for Receiver 18g36.2.1 OBE Receiver Sensitivity . 18g36.2.2 OBE Receiver Blocking 18g3Annex A (informative): Relationship between the present document a
17、nd the essential requirements of Directive 2014/53/EU . 19g3Annex B (informative): Change history . 20g3History 21g3ETSI ETSI EN 302 608 V2.1.1 (2017-11) 5 Intellectual Property Rights Essential patents IPRs essential or potentially essential to the present document may have been declared to ETSI. T
18、he information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available f
19、rom the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314
20、 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are i
21、ndicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Harmo
22、nised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.8 to provide one voluntary means of conforming to the e
23、ssential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.1. Once the present document is cited in the Official Journal of the European Union under that Dir
24、ective, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive and associated EFTA regulations. National transpositio
25、n dates Date of adoption of this EN: 27 November 2017 Date of latest announcement of this EN (doa): 28 February 2018 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 August 2018 Date of withdrawal of any conflicting National Standard (dow): 31 August 2019 Mod
26、al verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are
27、NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 302 608 V2.1.1 (2017-11) 6 Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment w
28、ithin the scope of the Directive 2014/53/EU i.1. The Eurobalise transmission system is defined by the specifications 1 and 2 of the UNISIG consortium. ETSI ETSI EN 302 608 V2.1.1 (2017-11) 7 1 Scope The present document specifies technical characteristics and methods of measurements for radio transm
29、itters and receivers used in the Eurobalise transmission system. The system is used in railway environment for the communication between tracks and trains. It applies to the following equipment units: a) the On-Board Equipment (OBE) Tele-powering the Eurobalise; and b) the Eurobalise that is always
30、installed in between the rails. The OBE comprises a transmitter (normally un-modulated) and a receiver fitted with an integral or dedicated antenna. The Eurobalise FSK-modulated transmitter is Tele-powered by the OBE and has an integral antenna. The Eurobalise transmission system operates in frequen
31、cy bands listed in table 1 in accordance with the EC Decision 2013/752/EU i.5 and ERC Recommendation 70-03 i.2, annex 4. These radio equipment types are capable of operating at the following frequencies as given in table 1. Table 1: Radio communications frequencies Radio communications frequencies N
32、ote OBE receive frequency band 2,5 MHz to 6 MHz (4,234 MHz centre frequency) Eurobalise transmit frequency band 4,234 MHz 1 MHz NOTE: EC decision for SRDs i.5 and ERC Recommendation 70-03 i.2 are providing the usage conditions for Eurobalise transmissions in frequency range 984 - 7 484 kHz (4,234 MH
33、z centre frequency). The 27 MHz band is only used in the OBE for telepowering the Eurobalise, which is not in the scope of the present document. The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU i.1 under the conditions identified in annex A. 2 References
34、2.1 Normative references References are specific, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicly available in the expected location might be found at https:/docbox.etsi.org/Reference/.
35、 NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 UNISIG SUBSET-036-3.1.0: “FFFIS for Eurobalise“, December 2015. N
36、OTE: Available at http:/www.era.europa.eu/Document-Register/Documents/SUBSET-036%20v310.pdf. 2 UNISIG SUBSET-085-3.0.0: “Test Specification for Eurobalise FFFIS“, February 2012. NOTE: Available at http:/www.era.europa.eu/Document-Register/Documents/Set-2-Index043-SUBSET-085%20v300.pdf. ETSI ETSI EN
37、302 608 V2.1.1 (2017-11) 8 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced
38、 document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the
39、 user with regard to a particular subject area. i.1 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.2 CEPT/
40、ERC/Recommendation 70-03: “Relating to the use of Short Range Devices (SRD)“. i.3 ETSI TR 100 028 (V1.4.1) (12-2001) (all parts): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics“. i.4 ETSI TR 102 273 (V1.2.1)
41、 (all parts): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and evaluation of the corresponding measurement uncertainties“. i.5 EC Decision 2013/752/EU: “Commission Implementing DECISION of 11 December 2013 amending
42、Decision 2006/771/EC on harmonisation of the radio spectrum for use by short-range devices and repealing Decision 2005/928/EC“. i.6 ETSI EN 300 330 (V2.1.1): “Short Range Devices (SRD); Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in the frequency range 9 kHz to
43、30 MHz; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU“. i.7 CENELEC EN 50121-2:2015: “Railway applications - Electromagnetic compatibility - Part 2: Emission of the whole railway system to the outside world“. Applies in conjunction with EN 50121-1
44、 (09-2000). i.8 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the
45、European Parliament and of the Council. i.9 UNISIG SUBSET-116-1.1.0: “Eurobalise On-board Equipment, Susceptibility Test Specification“, June 2016. NOTE: Available at http:/www.era.europa.eu/Document-Register/Pages/Set-3-Eurobalise-On-board-equipment-susceptibility-test-specification.aspx. 3 Definit
46、ions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: dedicated antenna: removable antenna supplied and tested with the radio equipment, designed as an indispensable part of the equipment duty cycle: defined as the ratio,
47、 expressed as a percentage, of the maximum transmitter “on“ time monitored over one hour, relative to a one hour period ETSI ETSI EN 302 608 V2.1.1 (2017-11) 9 Eurobalise: wayside transmission unit that uses the magnetic transponder technology NOTE: Its main function is to transmit and/or receive si
48、gnals through the air gap. The Eurobalise is a single device mounted on the track, which communicates with a train passing over it. integral antenna: permanent fixed antenna, which may be built-in, designed as an indispensable part of the equipment intersystem interference: interference from sources
49、 not under the control of the operator or manufacturer of the equipment intrasystem interference: interference from source that are part of the system and are under the control of the manufacturer or the operator of the equipment magnetic transponder technology: method that uses magnetic coupling in the air gap between a transmitter and a receiver for conveying data and energy NOTE: In the Eurobalise transmission system context, it considers systems using the 27,095 MHz for Tele-powering and 4,234 MHz for Up-link transmission. O
