1、STD-ETSI ETS 300 31iZ-L-ENGL 1997 3900855 02072b4 91T EUROPEAN T 1 ELECOMMUNICATION STANDARD ETS 300 342-1 June 1997 Second Edition Source: ETSI TC-RES Reference: RE/RES-09035-1 ICs: 33.020 Key words: DCS, EMC, GSM, radio, testing Radio Equipment and Systems (RES); ElectroMagnetic Compatibility (EMC
2、) for European digital cellular telecommunications system (GSM 900 MHz and DCS 1 800 MHz) Part 1 : Mobile and portable radio and ancillary equipment ETSI European Telecommunications Standards Institute ETSI Secretariat Postal address: F-O6921 Sophia Antipolis CEDEX - FRANCE Office address: 650 Route
3、 des Lucioles - Sophia Antipolis - Valbonne - FRANCE X.400: c=fr, a=atlas, p=etsi, c=secretariat - Internet: secretariat8 etsi.fr Tel.: +33 4 92 94 42 O0 - Fax: +33 4 93 65 47 16 Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the foreg
4、oing restriction extend to reproduction in all media. O European Telecommunications Standards Institute 1997. All rights reserved. STD-ETSI ETS 300 342-L-ENGL 1777 3400855 02072b5 85b = Page 2 ETC 300 342-1: June 1997 Whilst every care has been taken in the preparation and publication of this docume
5、nt, errors in content, typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to “ETSI Editing and Committee Support Dept.“ at the address shown on the title page. STD-ETSI ETS 300 392-L-ENGL 1777 M 3Li00855 02072bb 772 M Page 3 ETS 300 342-1 : June 1997 Co
6、ntents Foreword . ,._._. 5 Scope . 7 Normative references . ._._. 7 Definitions. symbols and abbreviations 8 Definitions ._ _ . 8 Symbols -. 9 3.3 Abbreviations . 9 3.1 3.2 General test conditions 10 4.1 Test conditions and configurations 10 4.2 Emission measurements . 10 4.3 Immunity tests 10 4.4 N
7、ormal test modulation . 1.1 4.5 Arrangements for test signals at the input of the transmitter . 12 4.6 Arrangements for test signals at the output of the transmitter . 12 4.7 Arrangements for test signals at the input of the receiver . 12 4.8 Arrangements for test signals at the output of the receiv
8、er . 13 4.9 Receiver and duplex transceiver exclusion band . -13 4.1 O Transmitter exclusion band . 31 4.1 1 Narrow band responses on receivers and duplex transceivers . 13 4.12 Idle Mode ._. . 14 Performance assessment . 14 5.1 General ._ 14 5.2 Equipment which can provide a communication link . 14
9、 5.3 Equipment which does not provide a communication link . 14 5.4 Conformance of ancillary equipment . 14 5.5 Equipment classification . 15 Performance criteria 15 6.1 Performance criteria for Continuous phenomena applied to Transmitters (CT) 15 6.2 Performance criteria for Transient phenomena app
10、lied to Transmitters (TT) . 15 6.3 Performance criteria for Continuous phenomena applied to Receivers (CR) 16 6.4 Performance criteria for Transient phenomena applied to Receivers (TR) . 16 Applicability overview tables . . 16 7.1 Emission 16 7.2 Immunity ._._._. 17 Test methods and limits for emiss
11、ion measurements . 17 8.1 Enclosure, ancillary equipment 17 8.1.1 Definition . 17 8.1.2 Test method . -17 8.1.3 Limits . 18 DC power input/output port 18 8.2.1 Definition . 18 8.2.2 Test method 18 8.2.3 Limits . 18 AC mains power input/output port 19 8.3.1 Definition . 19 8.3.2 Test method 19 8.3.3
12、Limits . 19 8.2 8.3 STD-ETSI ETS 300 3Li2-L-ENGL 1997 3400855 02072b7 b29 Page 4 ETS 300 342-1 : June 1997 9.2 9.3 9.4 9.5 9.6 9.7 9 Test methods and levels for immunity tests . 39 9.1 RF electromagnetic field (80 . 1 O00 MHz) . 19 9.1.1 Definition . 19 9.1.2 Test method and level 20 9.1.3 performan
13、ce criteria . 20 Electrostatic discharge . _. 20 9.2.1 Definition . 20 9.2.2 Test method and level 20 9.2.3 Performance criteria . 20 Fast transients common mode 21 9.3.1 Definition . 21 9.3.2 Test method and level 21 9.3.3 Performance criteria . 21 RF common mode, O, 15 MHz - 80 MHz (current clamp
14、injection) 21 9.4.1 Definition . 22 9.4.2 Test method and level 22 9.4.3 Performance criteria . 22 Transients and surges, vehicular environment . 22 9.5.1 Defini ti on . 23 9.5.2 Test method and level 23 9.5.3 Performance criteria . 24 Voltage dips and interruptions . 24 9.6.1 Definition . 24 9.6.2
15、Test method and level 24 9.6.3 Performance criteria . 24 Surges, common and differential mode 25 9.7.1 Definition . 25 9.7.2 Test method and level 25 9.7.3 Performance criteria . 25 Annex A (normative): Clauses and/or subclauses addressing essential requirements of EC Council Directives . 26 History
16、 27 STD-ETSI ETS 300 3q2-L-ENGL 1777 U 3400855 02072b8 5b5 Page 5 ETS 300 342-1 : June 1997 Fore word This European Telecommunication Standard (ETS) has been produced by the European Telecommunications Standards Institute (ETSI) in response to a mandate from the European Commission issued under Coun
17、cil Directive 83/189/EEC (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. This ETS is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities refer
18、encing the Council Directive on the approximation of the laws of the Member States relating to electromagnetic compatibility (“the EMC Directive“) (89/336/EEC as amended). Technical specifications relevant to the EMC Directive are given in annex A. This ETS consists of 3 parts as follows: Part 1 : “
19、Mobile and portable radio and ancillary equlpment“; Part 2: “Base station radio and ancillary equipment (Phase 1)“ (RE/RES-09035-2); Part 3: “Base station radio and ancillary equipment (Phase 2)“ (DE/RES-09035-3). Transposition dates Date of adoption: Date of latest announcement of this ETS (doa): 6
20、 June 1997 30 September 1997 Date of latest publication of new National Standard or endorsement of this ETS (dop/e): 31 March 1998 I Date of withdrawal of any conflicting National Standard (dow): 31 March 1998 I STD-ETSI ETS 300 3q2-1-ENGL 1997 3400855 0207269 LiTL Page 7 ETS 300 342-1: June 1997 1
21、Scope This second edition European Telecommunication Standard (ETC) covers the assessment of radio communication and ancillary equipment in respect of ElectroMagnetic Compatibility (EMC). Technical specifications related to the antenna port and emissions from the enclosure port of radio equipment ar
22、e found in the related product standards for the effective use of the radio spectrum. This ETS specifies the applicable EMC tests, the methods of measurement, the frequency range, the limits and the minimum performance criteria for Phase 1 and Phase 2 GSM 900MHz and DCS 1 800 MHz digital public cell
23、ular mobile and portable radio equipment, transmitting and receiving speech and/or data, and the associated ancillary equipment. Base station equipment operating within network infrastructure is outside the scope of this ETS. However, this ETS does cover mobile and portable equipment that is intende
24、d to be operated in a fixed location while connected to the AC mains. The environment classification used in this ETS refers to the environment classification used in the Generic Standards EN 50081-1 l, EN 50082-1 2, except the vehicular environment class which refers to IS0 7637 Part 1 3 and Part 2
25、 4. For the purposes of this ETS, Mobile Stations (MS) are considered to be radio communications equipment. The EMC requirements have been selected to ensure an adequate level of compatibility for apparatus in residential, commercial, light industrial and vehicular environments. The levels however,
26、do not cover extreme cases which may occur in any location but with low probability of occurrence. This ETS may not cover those cases where a potential source of interference which is producing individually repeated transient phenomena, or a continuous phenomena, is permanently present, e.g. a radar
27、 or broadcast site in the near vicinity. In such a case it may be necessary to use special protection applied to either the source of interference or the interfered part or both. Compliance of radio equipment to the requirements of this ETS does not signify compliance to any requirement related to t
28、he use of the equipment (i.e. licensing requirements). Compliance to this ETS does not signify compliance to any safety requirement. However, it is the responsibility of the assessor of the equipment that any observation regarding the equipment becoming dangerous or unsafe as a result of the applica
29、tion of the tests of this ETS, should be recorded in the test report. 2 Normative references This ETS incorporates, by dated or undated reference, provisions from other publications. These normative and informative references are cited at the appropriate places in the text and the publications liste
30、d hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this ETC only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies. 31 41 EN 50081-1 (1 992): “Electromagnetic
31、 compatibility - Generic emission standard. Part 1: Residential, commercial and light industry“. EN 50082-1 (1 992): “Electromagnetic compatibility - Generic immunity standard. Part 1: Residential, commercial and light industry“. IS0 7637-1 (1990): “Road vehicles - Electrical disturbance by conducti
32、on and coupling - Part 1: Passenger cars and light commercial vehicles with nominal 12 V supply voltage - Electrical transient conduction along supply lines only“. IS0 7637-2 (1990): “Road vehicles - Electrical disturbance by conduction and coupling - Part 2: Commercial vehicles with nominal 24 V su
33、pply voltage - Electrical transient conduction along supply lines only“. Previous page is blank STD=ETSI ETS 300 342-L-ENGL 1777 3400855 O207270 LL3 = Page 8 ETS 300 342-1: June 1997 51 71 91 i 31 i 41 i 51 I-ETS 300 034-1 (1993-1 O): “European digital cellular telecommunications system (Phase 1); R
34、adio sub-system link control (GSM 05.08)“. LETS 300 034-2 (1993-9): “European digital cellular telecommunications system (Phase 1); Radio sub-system link control Part 2: DCS extension (GSM 05.08- DCS)“. ETS 300 578 Edition 6 (1 996-8): “Digital cellular telecommunications system (Phase 2); Radio sub
35、system link control (GSM 05.08)“. EN 55022 (1994): “Limits and methods of measurement of radio disturbance characteristics of information technology equipment“. CISPR 16-1 (1993): “Specification for radio disturbance and immunity measuring apparatus and methods - Part 1: Radio disturbance and immuni
36、ty measuring apparatus“. EN 61000-4-3: “Electromagnetic Compatibility (EMC) - Part 4: Testing and measurements techniques - Section 3: Radiated, radio-frequency, electromagnetic field immunity test“. EN 61000-4-2: “Electromagnetic Compatibility (EMC) - Part 4: Testing and measurements techniques - S
37、ection 2: Electrostatic discharge immunity test. Basic EMC publication“. EN 61 000-4-4: “Electromagnetic Compatibility (EMC); Part 4: Testing and measurements techniques - Section 4: Electrical fast transienthurst immunity test. Basic EMC publication“. EN 61000-4-6: “Electromagnetic Compatibility (E
38、MC) - Part 4: Testing and measurements techniques - Section 6: Immunity to conducted disturbances induced by radio-frequency fields“. EN 61000-4-1 1: “Electromagnetic Compatibility (EMC); Part 4: Testing and measurements techniques - Section 1 1 : Voltage dips, short interruptions and voltage variat
39、ions immunity tests“. EN 61 000-4-5: “Electromagnetic Compatibility (EMC) - Part 4: Testing and measurements techniques - Section 5: Surge immunity test“. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of this ETS, the following definitions apply: ancillary equipment: Equi
40、pment (apparatus), used in connection with a receiver, transmitter or transceiver, is considered as an ancillary equipment (apparatus) if: - the equipment is intended for use in conjunction with a receiver, transmitter or transceiver to provide additional operational and/or control features to the r
41、adio equipment (e.g. to extend control to another position or location); and - the equipment cannot be used on a stand alone basis to provide user functions independently of a receiver, transmitter or transceiver; and - the receiver, transmitter or transceiver to which it is connected, is capable of
42、 providing some intended operation such as transmitting and/or receiving without the ancillary equipment (i.e. it is not a sub-unit of the main equipment essential to the main equipment basic functions). base station equipment: Mobile or portable equipment that is also intended to operate in a fixed
43、 location and powered from the AC mains. STD-ETSI ETS 300 3Y2-L-ENGL 1777 3q00855 0207273 05T = Page 9 ETS 300 342-1 : June 1997 idle mode: A mode of operation of a receiver or a transceiver, where the Equipment Under Test (EUT) is powered, available for service and available to respond to a request
44、 to set up a call. integral antenna equipment: Equipment fitted with an antenna designed to be connected to the equipment without the use of an external connector and considered to be part of the equipment. An integral antenna may be fitted internally or externally to the equipment. port: A particul
45、ar interface of the specified equipment (apparatus) with the electromagnetic environment. radio communications equipment: An apparatus which includes one or more transmitters and/or receivers and/or parts thereof. This type of equipment (apparatus) can be used in a fixed, mobile or a portable applic
46、ation. RXQUAL: A measure of the received signal quality, which is generated by the mobile or portable equipment, for use as a criterion in the Radio Frequency (RF) power control and handover processes. For more information see: - LETS 300 034-1 5 subclause 8.2 for Phase 1 GSM 900 equipment; - I-ETS
47、300 034-2 6 subclause 8.2 for Phase 1 DCS 1800 equipment; or - ETS 300 578 Edition 6 7 subclause 8.2 for Phase 2 GSM 900 or Phase 2 DCS 1800 equipment. standby mode: Mode of operation of a transmitter, where the EUT is powered, and available for transmission on demand. 3.2 Symbols For the purposes o
48、f this ETS, the following symbols apply: AC Alternating Current DC Direct Current BPF BandPass Filter BW Bandwidth CF Centre Frequency emf electromotive force rms root mean square RXQUAL RX Quality 3.3 Abbreviations For the purposes of this ETS, the following abbreviations apply: ARFCN BCCH BS CCCH
49、CR CT DTX EMC ERP EUT LISN M RP MS RF SPL TR TT Absolute Radio Frequency Channel Number Broadcast Control Channel Base Station Common Control CHannel Continuous phenomena applied to Receivers (subclause 6.3) Continuous phenomena applied to Transmitters (subclause 6.1) Discontinuous Transmission ElectroMagnetic Compatibility Ear Reference Point Equipment Under Test Line Impedance Stabilizing Network Mouth Reference Point Mobile Station Radio Frequency Sound Pressure Level Transient phenomena applied to Receivers (subclause 6.4) Transient phenomena applied to Transmit
